| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | COMPRESSOR WITH MAGNET CLUTCH | - | - | - | - |
| 2 | GENERATOR ASSEMBLY | 27060 | - | - | - |
| 3 | WATER OUTLET PIPE WITH WATER BY-PASS JOINT | - | - | - | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | ★ | Precoated part |
|
Do not apply lubricants to the threads | - | - |
| *1 | NO. 1 IDLE GEAR SHAFT | *2 | NO. 2 IDLE GEAR SHAFT |
| *3 | OIL PUMP DRIVE SHAFT SPROCKET | *4 | CRANKSHAFT TIMING GEAR KEY |
| *5 | OIL PUMP DRIVE SPROCKET | *6 | CHAIN TENSIONER PLATE |
| *7 | CHAIN DAMPER SPRING | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 33 | TIMING CHAIN COVER ASSEMBLY | 11310 | - | - | - |
| 34 | NO. 6 ENGINE COVER | 12616 | - | - | - |
| ● | Non-reusable part | - | - |
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1.REMOVE COMPRESSOR WITH MAGNET CLUTCH
27060 2.REMOVE GENERATOR ASSEMBLY
for DENSO Made:
Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>GENERATOR (for DENSO Made)>REMOVAL
for VALEO Made:
Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>GENERATOR (for VALEO Made)>REMOVAL
3.REMOVE WATER OUTLET PIPE WITH WATER BY-PASS JOINT
4.REMOVE OIL COOLER ASSEMBLY WITH OIL FILTER SUB-ASSEMBLY
16620D 5.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
12502 6.REMOVE CHAIN COVER AND COMPRESSOR BRACKET SUB-ASSEMBLY
16601 7.REMOVE V-RIBBED BELT TENSIONER SUB-ASSEMBLY
12501 8.REMOVE GENERATOR BRACKET SUB-ASSEMBLY
9.DISCONNECT WATER BY-PASS PIPE
Remove the 2 bolts and disconnect the water by-pass pipe.
Leave the water by-pass pipe on the engine side.
1629A 10.REMOVE NO. 14 WATER BY-PASS HOSE
16031 11.REMOVE WATER INLET SUB-ASSEMBLY WITH THERMOSTAT
16260 12.REMOVE WATER BY-PASS HOSE ASSEMBLY
Slide the clip and disconnect the water by-pass hose assembly from the timing chain cover assembly.
Using an 8 mm socket wrench, remove the 2 bolts and water by-pass hose assembly.
15370B 13.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY RH (for Intake Side of Bank 1)
15370B 15.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY RH (for Exhaust Side of Bank 1)
15370D 16.REMOVE CAM TIMING OIL CONTROL SOLENOID RH O-RING (for Exhaust Side of Bank 1)
15370C 17.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY LH (for Intake Side of Bank 2)
15370C 19.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY LH (for Exhaust Side of Bank 2)
15370E 20.REMOVE CAM TIMING OIL CONTROL SOLENOID LH O-RING (for Exhaust Side of Bank 2)
11302 24.REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY
| *a | Protective Tape | - | - |
Remove the 27 bolts shown in the illustration.
Remove the timing chain or belt cover sub-assembly by prying between the timing chain or belt cover sub-assembly and timing chain cover assembly with a screwdriver.
Be careful not to damage the contact surfaces of the timing chain or belt cover sub-assembly and timing chain cover assembly.
Tape the screwdriver tip before use.
Remove the 2 water pump gaskets from the timing chain cover assembly.
13507C 25.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY
| *1 | Chain Tensioner Plate | *2 | Chain Damper Spring |
|
Push |
|
Remove in this Direction |
Using the hexagonal portion of the camshaft, secure the camshaft.
Loosen the oil pump drive shaft gear nut.
While pushing the chain damper spring, remove the chain tensioner plate and chain damper spring as shown in the illustration.
Remove the oil pump drive shaft gear nut.
Remove the oil pump drive sprocket, oil pump drive shaft sprocket and oil pump drive chain sub-assembly.
13559 27.REMOVE CHAIN TENSIONER SLIPPER
13561 30.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13562 31.REMOVE NO. 2 CHAIN VIBRATION DAMPER
13521 32.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET
11310 33.REMOVE TIMING CHAIN COVER ASSEMBLY
12616 34.REMOVE NO. 6 ENGINE COVER