| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | NO. 1 TURBOCHARGER SUB-ASSEMBLY | 17201A | - | - | - |
| 2 | NO. 5 ENGINE COVER | 12615A | - | - | - |
| 3 | NO. 2 TURBOCHARGER SUB-ASSEMBLY | 17208 | - | - | - |
| 4 | NO. 4 ENGINE COVER | 12614A | - | - | - |
| 5 | NO. 1 TURBO INSULATOR STAY | 17273 | - | - | - |
| 6 | NO. 1 WATER BY-PASS PIPE | 16268 | - | - | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 35 | SPARK PLUG | 19100P | ( ) |
- | - |
| 36 | CYLINDER HEAD COVER SUB-ASSEMBLY RH | 11201M | ( ) |
- | - |
| 37 | SPARK PLUG TUBE GASKET RH | 11193B | ( ) |
- | - |
| *1 | CAMSHAFT POSITION SENSOR (for Intake Side of Bank 1) | *2 | CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 1) |
| *3 | NO. 1 INTERCOOLER AIR GUIDE | *4 | OIL FILLER CAP ASSEMBLY |
| ● | Non-reusable part | ★ | Precoated part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 38 | SPARK PLUG | 19100P | ( ) |
- | - |
| 39 | CYLINDER HEAD COVER SUB-ASSEMBLY LH | 11202 | ( ) |
- | - |
| 40 | SPARK PLUG TUBE GASKET LH | 11193A | ( ) |
- | - |
| *1 | CAMSHAFT POSITION SENSOR (for Intake Side of Bank 2) | *2 | CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 2) |
| ● | Non-reusable part | ★ | Precoated part |
| ● | Non-reusable part | ★ | Precoated part |
| *1 | TIMING CHAIN COVER PLATE | - | - |
| ● | Non-reusable part | ★ | Precoated part |
|
Do not apply lubricants to the threads | - | - |
| *1 | NO. 1 IDLE GEAR SHAFT | *2 | NO. 2 IDLE GEAR SHAFT |
| *3 | OIL PUMP DRIVE SHAFT SPROCKET | *4 | CRANKSHAFT TIMING GEAR KEY |
| *5 | OIL PUMP DRIVE SPROCKET | *6 | CHAIN TENSIONER PLATE |
| *7 | CHAIN DAMPER SPRING | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 69 | TIMING CHAIN COVER ASSEMBLY | 11310 | - | - | - |
| 70 | NO. 6 ENGINE COVER | 12616 | - | - | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | ★ | Precoated part |
| *1 | NO. 2 CHAIN SUB-ASSEMBLY | *2 | FUEL PUMP LIFTER HOUSING RH |
| *3 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY) | *4 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY) |
| ● | Non-reusable part | - | - |
| *1 | NO. 2 CHAIN SUB-ASSEMBLY | *2 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY) |
| *3 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY) | - | - |
| ● | Non-reusable part | - | - |
| *1 | PLATE WASHER | *2 | CYLINDER HEAD SET BOLT |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 108 | RING PIN | - | ( ) |
- | - |
| *1 | CAMSHAFT HOUSING SUB-ASSEMBLY RH | *2 | CAMSHAFT HOUSING SUB-ASSEMBLY LH |
| ● | Non-reusable part | - | - |
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
17201A 1.REMOVE NO. 1 TURBOCHARGER SUB-ASSEMBLY
12615A 2.REMOVE NO. 5 ENGINE COVER
17208 3.REMOVE NO. 2 TURBOCHARGER SUB-ASSEMBLY
12614A 4.REMOVE NO. 4 ENGINE COVER
17273 5.REMOVE NO. 1 TURBO INSULATOR STAY
16268 6.REMOVE NO. 1 WATER BY-PASS PIPE
23891 9.REMOVE FUEL DELIVERY SPACER
23291 10.REMOVE INJECTOR VIBRATION INSULATOR
17111 11.REMOVE INTAKE MANIFOLD
82125N 15.REMOVE NO. 5 ENGINE WIRE
23695A 16.REMOVE NOZZLE HOLDER CLAMP
23250B 19.REMOVE FUEL INJECTOR O-RING
23256 20.REMOVE NO. 1 FUEL INJECTOR BACK-UP RING
21.REMOVE C-RING
23291A 22.REMOVE INJECTOR VIBRATION INSULATOR
82126A 26.REMOVE NO. 6 ENGINE WIRE
23695A 27.REMOVE NOZZLE HOLDER CLAMP
23250B 30.REMOVE FUEL INJECTOR O-RING
23256 31.REMOVE NO. 1 FUEL INJECTOR BACK-UP RING
32.REMOVE C-RING
23291A 33.REMOVE INJECTOR VIBRATION INSULATOR
11193B 37.REMOVE SPARK PLUG TUBE GASKET RH
Remove the 3 spark plug tube gaskets.
Be careful not to damage the spark plug tube gaskets when removing it as the removed spark plug tube gaskets need to be used when installing a new one.
11193A 40.REMOVE SPARK PLUG TUBE GASKET LH
Remove the 3 spark plug tube gaskets.
Be careful not to damage the spark plug tube gaskets when removing it as the removed spark plug tube gaskets need to be used when installing a new one.
16031 41.REMOVE WATER INLET SUB-ASSEMBLY WITH THERMOSTAT
15601 45.REMOVE OIL FILTER SUB-ASSEMBLY
15710 46.REMOVE OIL COOLER ASSEMBLY
15785 47.REMOVE OIL COOLER GASKET
15710B 48.REMOVE OIL COOLER O-RING
15370B 49.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY RH (for Intake Side of Bank 1)
15370B 51.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY RH (for Exhaust Side of Bank 1)
15370D 52.REMOVE CAM TIMING OIL CONTROL SOLENOID RH O-RING (for Exhaust Side of Bank 1)
15370C 53.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY LH (for Intake Side of Bank 2)
15370C 55.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY LH (for Exhaust Side of Bank 2)
15370E 56.REMOVE CAM TIMING OIL CONTROL SOLENOID LH O-RING (for Exhaust Side of Bank 2)
58. SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *1 | Crankshaft Pulley Set Key | - | - |
| *a | Block Bore Center Mark RH | *b | 30° |
Temporarily install the crankshaft pulley set bolt.
Set the crankshaft pulley set key to the block bore center mark RH (TDC/compression).
| *a | Timing Mark (Camshaft Timing Intake Gear Assembly Side) | *b | Timing Mark (Camshaft Timing Exhaust Gear Assembly Side) |
for Bank 1:
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°) and align the timing marks as described above.
Check each timing mark from a viewpoint directly inline with the center of the camshaft and the timing mark on each camshaft timing gear.
If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.
| *a | Timing Mark (Camshaft Timing Intake Gear Assembly Side) | *b | Timing Mark (Camshaft Timing Exhaust Gear Assembly Side) |
for Bank 2:
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°) and align the timing marks as described above.
Check each timing mark from a viewpoint directly inline with the center of the camshaft and the timing mark on each camshaft timing gear.
If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.
13540 62.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
| *a | Plunger | *b | Stopper Plate |
| *c | Pin | - | - |
Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.
Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm (0.0500 in.) diameter into the stopper plate's hole.
Remove the 2 bolts and No. 1 chain tensioner assembly.
13559 63.REMOVE CHAIN TENSIONER SLIPPER
13506A 64.REMOVE NO. 1 CHAIN SUB-ASSEMBLY
| *A | for Bank 1 | - | - |
| *1 | Crankshaft Pulley Set Key | - | - |
| *a | 10° | *b | Timing Mark |
Turn the crankshaft counterclockwise 10° to loosen the chain sub-assembly of the crankshaft timing sprocket.
Remove the crankshaft pulley set bolt.
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.
Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 70°) and set it as shown in the illustration. Be sure to loosen the chain between the banks.
Remove the No. 1 chain sub-assembly.
13530 65.REMOVE IDLE SPROCKET ASSEMBLY
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.
13561 66.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13562 67.REMOVE NO. 2 CHAIN VIBRATION DAMPER
13521 68.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET
11310 69.REMOVE TIMING CHAIN COVER ASSEMBLY
Remove the 27 bolts shown in the illustration.
Timing Chain Cover Assembly Side:
Remove the 2 oil pump gaskets and 2 water pump gaskets from the timing chain cover assembly.
Cylinder Block Sub-assembly Side:
Remove the 3 oil pump gaskets from the cylinder block sub-assembly.
12616 70.REMOVE NO. 6 ENGINE COVER
12144 71.REMOVE OIL PAN COVER SILENCER
12101A 72.REMOVE OIL PAN DRAIN PLUG
12102A 73.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
| *A | Type A | *B | Type B |
| *a | Oil Pan Seal Cutter | - | - |
|
Bolt |
|
Nut |
Remove the 9 bolts and 2 nuts.
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
Be careful not to damage the contact surfaces of the oil pans.
12101R 75.REMOVE NO. 1 OIL PAN SUB-ASSEMBLY
Remove the 12 bolts.
Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.
Remove the No. 1 oil pan sub-assembly by prying between the No. 1 oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.
Be careful not to damage the contact surfaces of the cylinder block sub-assembly and No. 1 oil pan sub-assembly.
Tape the screwdriver tip before use.
15104 76.REMOVE OIL STRAINER SUB-ASSEMBLY
12121 77.REMOVE NO. 1 OIL PAN BAFFLE PLATE
11381 78.REMOVE REAR ENGINE OIL SEAL RETAINER
Remove the small head 6 bolts and 4 bolts.
Using a screwdriver, pry out the rear engine oil seal retainer.
Be careful not to damage the rear engine oil seal retainer.
Tape the screwdriver tip before use.
Remove the gasket from the rear engine oil seal retainer.
11381A 79.REMOVE REAR ENGINE OIL SEAL
| *a | Wooden Block | *b | Protective Tape |
Place the rear engine oil seal retainer on wooden blocks.
Be careful not to damage the rear engine oil seal retainer.
Using a screwdriver and a hammer, tap out the rear engine oil seal.
Tape the screwdriver tip before use.
13550 81.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
13501B 82.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY RH
13502C 84.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY RH
13801L 87.REMOVE VALVE ROCKER ARM SUB-ASSEMBLY RH
13750 88.REMOVE VALVE LASH ADJUSTER ASSEMBLY (for Bank 1)
13716 89.REMOVE VALVE STEM CAP (for Bank 1)
13560A 91.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
13054A 92.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY LH
13053B 94.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY LH
13802B 97.REMOVE VALVE ROCKER ARM SUB-ASSEMBLY LH
13750 98.REMOVE VALVE LASH ADJUSTER ASSEMBLY (for Bank 2)
13716 99.REMOVE VALVE STEM CAP (for Bank 2)
11115B 101.REMOVE CYLINDER HEAD GASKET RH
11116H 103.REMOVE CYLINDER HEAD GASKET LH
82219C 104.REMOVE SENSOR WIRE
12211 107.REMOVE NO. 1 PCV CASE (NO. 1 VENTILATION CASE)
11151 108.REMOVE RING PIN
|
|
| *A | for Bank 1 | *B | for Bank 2 |