| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | NO. 1 COOLING UNIT BRACKET | 88536 | - | - | - |
| 2 | NO. 2 COOLING UNIT BRACKET | 88536A | - | - | - |
| 3 | AIR CONDITIONER UNIT ASSEMBLY | - | - | - | - |
| 4 | COOLER UNIT DRAIN HOSE GROMMET | 88539G | ( ) |
- | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 5 | INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY | - | ( ) |
- | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| *A | w/ PTC Heater | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| *A | w/ Telematics Transceiver | *B | w/ Door Control Battery |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *A | w/ Headup Display | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 37 | FRONT SEAT ASSEMBLY LH | - | - | - | - |
| 38 | FRONT SEAT ASSEMBLY RH | - | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Compressor oil ND-OIL 8 or equivalent | - | - |
| *1 | ENGINE SIDE COVER SUB-ASSEMBLY LH | *2 | ENGINE SIDE COVER SUB-ASSEMBLY RH |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
88536 1.INSTALL NO. 1 COOLING UNIT BRACKET
88536A 2.INSTALL NO. 2 COOLING UNIT BRACKET
3.INSTALL AIR CONDITIONER UNIT ASSEMBLY
88539G 4.INSTALL COOLER UNIT DRAIN HOSE GROMMET
| *a | Driver Side | *b | Passenger Side |
| *c | Lip | - | - |
Press the entire upper surface of the new cooler unit drain hose grommet, and fit the entire circumference of the lip to the hole.
If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.
Make sure that the entire lip of the cooler unit drain hose grommet is securely engaged to the vehicle body.
5.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY
|
|
| *a | Guide | *b | Clamp |
|
Install to Guide by Inserting to the End | - | - |
Connect the connector and attach the clamp.
Install the instrument panel reinforcement assembly with air conditioning unit assembly to the guide as shown in the illustration.
Be careful not to damage the internal components of the instrument panel reinforcement assembly and air conditioning unit assembly on the glass etc. Only perform installation after first taking the appropriate actions.
Make sure that both parts are securely installed to the guide.
| *a | Bolt (A) | *b | Bolt (B) |
| *c | Bolt (C) | *d | Bolt (D) |
| *e | Nut | - | - |
Temporarily install the 4 bolts (A) and bolt (B).
Temporarily install the 2 bolts (C) and bolt (D).
Temporarily install the nut.
Tighten the 4 bolts (A) and bolt (B).
Tighten the 2 bolts (C) and bolt (D).
Tighten the nut.
82141 6.CONNECT INSTRUMENT PANEL WIRE
55306A 7.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
| *a | Clamp | *b | Guide |
Temporarily install the No. 1 instrument panel brace sub-assembly with the 2 nuts and bolt.
Temporarily install the screw.
Tighten the 2 nuts and bolt.
Tighten the screw.
Attach the guide and connect the ground wire with the bolt.
Attach the clamp.
55307C 8.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
| *a | Clamp | *b | Guide |
Temporarily install the No. 2 instrument panel brace sub-assembly with the nut and bolt.
Check for the No. 2 instrument panel brace sub-assembly and air conditioner harness assembly do not interfere.
Temporarily install the screw.
Tighten the 2 nuts and bolt.
Tighten the screw.
Attach the guide and connect the ground wire with the bolt.
Attach the clamp.
82213E 9.INSTALL HEATER BLOWER WIRE (w/ PTC Heater)
87201 10.INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY
8598A 11.INSTALL DOOR CONTROL BATTERY (w/ Door Control Battery)
85940 12.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY
87212F 15.INSTALL REAR NO. 2 AIR DUCT
87212 16.INSTALL REAR NO. 1 AIR DUCT
87212H 17.INSTALL REAR NO. 4 AIR DUCT
| *a | Protrusion | *b | Cutout |
Insert the rear No. 4 air duct to the No. 2 air duct and attach the clip.
Align the cutout of the drain hose with the protrusion of the heater case and connect the drain hose.
Connect the drain hose to the cooler unit drain hose grommet.
87212K 18.INSTALL REAR NO. 6 AIR DUCT
87212G 19.INSTALL REAR NO. 3 AIR DUCT
| *a | Protrusion | *b | Cutout |
Insert the rear No. 3 air duct to the No. 1 air duct and attach the clip.
Align the cutout of the drain hose with the protrusion of the heater case and connect the drain hose.
Connect the drain hose to the cooler unit drain hose grommet.
87212J 20.INSTALL REAR NO. 5 AIR DUCT
88576C 21.INSTALL NO. 1 COOLER AIR DUCT
22.INSTALL TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (w/ Telematics Transceiver)
55084E 23.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY
58510D 24.INSTALL FRONT FLOOR CARPET ASSEMBLY
88650N 25.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
67918D 27.INSTALL REAR DOOR SCUFF PLATE LH
62413A 28.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure described for the LH side.
67917C 29.INSTALL REAR DOOR SCUFF PLATE RH
73220 30.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73210 31.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
Use the same procedure described for the LH side.
73233 32.INSTALL OUTER LAP BELT ANCHOR COVER
45250 33.INSTALL STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
for Power Tilt and Power Telescopic Steering Column:
83108 34.INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)
55990B 35.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY
36.INSTALL INSTRUMENT PANEL SAFETY PAD
37.INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION
38.INSTALL FRONT SEAT ASSEMBLY RH
Use the same procedure described for the LH side.
39.INSTALL HOLE PLUG
88897K 40.INSTALL COOLER PIPE GROMMET
88710K 41.CONNECT NO. 3 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
|
Rotate in this Direction | - | - |
Sufficiently apply compressor oil to a new O-rings and the fitting surface of the No. 3 air conditioning tube and accessory assembly.
ND-OIL 8 or equivalent
Install the 2 O-rings to the No. 3 air conditioning tube and accessory assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the No. 3 air conditioning tube and accessory assembly and rotate the 1-point tightening plate as shown in the illustration.
Do not apply excessive force to the No. 3 air conditioning tube and accessory assembly.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
Install the bolt.
87128 42.INSTALL HEATER GROMMET
87245A 43.CONNECT INLET HEATER WATER HOSE A
| *1 | Inlet Heater Water Hose A | *2 | Hose Clip |
| *a | View A | *b | Marking |
| *c | Hose Clip Installation Angle (120° From Above the Vehicle) | *d | Hose Clip Installation Range (1 to 5 mm (0.0394 to 0.196 in.)) |
| *e | Stopper | - | - |
Connect the inlet heater water hose A with its marking facing upward and install the hose clip within the range shown in the illustration.
Do not apply excessive force to the inlet heater water hose A.
87246A 44.CONNECT OUTLET HEATER WATER HOSE A
| *1 | Outlet Heater Water Hose A | *2 | Hose Clip |
| *a | View A | *b | Marking |
| *c | Hose Clip Installation Angle (120° From Above the Vehicle) | *d | Hose Clip Installation Range (1 to 5 mm (0.0394 to 0.196 in.)) |
| *e | Stopper | - | - |
Connect the outlet heater water hose A with its marking facing upward and install the hose clip within the range shown in the illustration.
Do not apply excessive force to the outlet heater water hose A.
55223A 45.CONNECT OUTER DASH PANEL INSULATOR
46.INSTALL WIRING HARNESS CLAMP BRACKET
51470C 47.CONNECT REAR ENGINE SIDE UNDER COVER ASSEMBLY LH
87237 48.INSTALL HEATER PIPING COVER
49.INSTALL FRONT WIPER MOTOR AND LINK
50.ADD ENGINE COOLANT
51.INSPECT FOR COOLANT LEAK
52. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
53.WARM UP ENGINE
54.INSPECT FOR REFRIGERANT LEAK
51410 55.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
53292A 56.INSTALL UPPER RADIATOR SUPPORT SEAL
11209 57.INSTALL V-BANK COVER SUB-ASSEMBLY