Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2021.04–2021.07
RM38G0E _51 Engine / Hybrid System _101047 STOP AND START _0469044 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Starter Signal Circuit  


DESCRIPTION

By using the starter delay circuit, the engine stop and start ECU can activate the ST NO. 2 relay (for starter motor operation) after activating the ST NO. 1 relay (for starter pinion operation) to operate the starter assembly.

WIRING DIAGRAM

A488187E01
0.135,8.052 0.448,8.25 0.313,0.198 10 false A 4.896,0.427 5.229,0.604 0.333,0.177 10 false 12 4.917,2.031 5.25,2.208 0.333,0.177 10 false 21 1.052,2.042 1.385,2.219 0.333,0.177 10 false 42 4.917,2.469 5.25,2.646 0.333,0.177 10 false 36 4.927,2.823 5.26,3 0.333,0.177 10 false 41 5.792,4.198 6.125,4.375 0.333,0.177 10 false 18 5.823,2.031 6.156,2.208 0.333,0.177 10 false 21 5.802,0.448 6.135,0.625 0.333,0.177 10 false 19 5.792,0.625 6.125,0.802 0.333,0.177 10 false I57 2.229,3.302 5.146,3.521 2.917,0.219 10 false Power Distribution Box Assembly 2.969,1.323 3.438,1.531 0.469,0.208 10 false ACC 3.865,0.771 4.583,0.979 0.719,0.208 10 false ECU-ACC 3.771,2.396 4.854,2.708 1.083,0.313 10 false ECU-IGR NO. 5 2.844,2.969 3.604,3.177 0.76,0.208 10 false IGR NO. 1 4.885,0.625 5.219,0.802 0.333,0.177 10 false 5C 4.896,2.229 5.229,2.406 0.333,0.177 10 false 5B 1.063,2.219 1.396,2.396 0.333,0.177 10 false 5B 4.896,2.646 5.229,2.823 0.333,0.177 10 false 5B 1.063,2.625 1.396,2.802 0.333,0.177 10 false 5B 4.896,2.979 5.229,3.156 0.333,0.177 10 false 5C 6.135,2.219 6.469,2.396 0.333,0.177 10 false IGR 6.146,4.385 6.479,4.563 0.333,0.177 10 false IGP 5.979,7.896 7.021,8.438 1.042,0.542 10 false Engine Stop and Start ECU 1.073,2.448 1.406,2.625 0.333,0.177 10 false 39 6.115,0.615 6.583,0.823 0.469,0.208 10 false ACC 4.563,4.552 5.677,4.792 1.115,0.24 10 false ECU-IGP NO. 3 3.323,5.146 4.083,5.354 0.76,0.208 10 false IGP NO. 1 4.49,8.115 4.823,8.292 0.333,0.177 10 false B 5.792,2.229 6.125,2.406 0.333,0.177 10 false I57 5.802,4.385 6.135,4.563 0.333,0.177 10 false I57 1.052,3.01 1.385,3.188 0.333,0.177 10 false 5B 1.052,2.833 1.365,3.031 0.313,0.198 10 false 11 1.438,2.385 2.198,2.594 0.76,0.208 10 false SMART 4.813,8.125 5.146,8.302 0.333,0.177 10 false C 3.99,4.292 4.146,4.49 0.156,0.198 10 false 5 3.073,4.302 3.229,4.5 0.156,0.198 10 false 3 3.99,4.719 4.146,4.917 0.156,0.198 10 false 2 3.073,4.719 3.229,4.917 0.156,0.198 10 false 1 2.26,7.813 3.823,8.198 1.563,0.385 10 false Certification ECU (Smart Key ECU Assembly) 2.385,6.115 3,6.313 0.615,0.198 10 false IGPD 2.375,6.49 2.99,6.688 0.615,0.198 10 false IGRD 2.385,6.854 3,7.052 0.615,0.198 10 false ACCD 2.385,7.24 2.698,7.438 0.313,0.198 10 false +B 3.365,6.417 3.823,6.615 0.458,0.198 10 false STA 3.281,7.021 3.896,7.219 0.615,0.198 10 false STAR 2.031,6.125 2.49,6.323 0.458,0.198 10 false I40 2.125,5.927 2.438,6.125 0.313,0.198 10 false 24 2.031,6.5 2.49,6.698 0.458,0.198 10 false I40 3.771,6.417 4.229,6.615 0.458,0.198 10 false I40 3.771,7.031 4.229,7.229 0.458,0.198 10 false I40 2.094,6.323 2.406,6.521 0.313,0.198 10 false 11 3.792,6.792 4.104,6.99 0.313,0.198 10 false 10 3.781,6.219 3.938,6.417 0.156,0.198 10 false 3 2.042,6.875 2.5,7.073 0.458,0.198 10 false I39 2.094,6.688 2.406,6.885 0.313,0.198 10 false 21 2.042,7.25 2.5,7.448 0.458,0.198 10 false I39 2.135,7.073 2.292,7.271 0.156,0.198 10 false 6 1.063,1.583 1.396,1.76 0.333,0.177 10 false 5K 1.073,0.656 1.406,0.833 0.333,0.177 10 false 5H 0.354,0.771 0.938,1.115 0.583,0.344 10 false PDB-ALT NO. 2 0.229,1.229 0.563,1.406 0.333,0.177 10 false ALT 0.396,1.719 1.354,1.896 0.958,0.177 10 false PDB-B 1.094,1.385 1.427,1.563 0.333,0.177 10 false 1 1.104,0.469 1.438,0.646 0.333,0.177 10 false 1

A488188E01
6.25,0.719 6.708,0.917 0.458,0.198 10 false CLL 6.281,1.188 6.74,1.385 0.458,0.198 10 false STA 6.26,1.594 6.875,1.792 0.615,0.198 10 false BNT1 6.281,2.667 6.594,2.865 0.313,0.198 10 false +B 1.677,2.094 3.021,2.49 1.344,0.396 10 false Park/Neutral Position Switch Assembly 0.167,0.104 0.323,0.302 0.156,0.198 10 false A 5.052,2.823 6.427,3.021 1.375,0.198 10 false EFI NO. 1 4.083,1.927 5.969,2.281 1.885,0.354 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 4,3.333 6.146,3.531 2.146,0.198 10 false EFI MAIN NO. 1 4.052,2.563 4.208,2.76 0.156,0.198 10 false 3 4.792,2.573 4.948,2.771 0.156,0.198 10 false 5 4.052,2.896 4.208,3.094 0.156,0.198 10 false 1 4.813,2.896 4.969,3.094 0.156,0.198 10 false 2 0.906,3.198 3.052,3.396 2.146,0.198 10 false EFI MAIN NO. 1 0.885,0.156 1.042,0.354 0.156,0.198 10 false B 3.427,0.208 3.583,0.406 0.156,0.198 10 false C 0.885,2.406 1.042,2.604 0.156,0.198 10 false D 5.448,3.323 5.604,3.521 0.156,0.198 10 false E 6.26,3.615 6.875,3.813 0.615,0.198 10 false BIN1 6.26,4.104 6.875,4.302 0.615,0.198 10 false BIN2 2.375,3.802 3.75,4 1.375,0.198 10 false BBC NO. 1 1.51,4.302 2.885,4.5 1.375,0.198 10 false BBC NO. 2 4.146,8.135 5.375,8.333 1.229,0.198 10 false ST NO. 2 1.865,5.542 3.094,5.74 1.229,0.198 10 false ST NO. 1 2.5,4.75 2.656,4.948 0.156,0.198 10 false 3 1.76,4.76 1.917,4.958 0.156,0.198 10 false 5 0.802,5.031 2.031,5.229 1.229,0.198 10 false ST NO. 1 2.5,5.083 2.656,5.281 0.156,0.198 10 false 2 1.75,5.063 1.906,5.26 0.156,0.198 10 false 1 3.927,6.094 5.156,6.292 1.229,0.198 10 false ST NO. 2 0.615,6.25 2.604,6.448 1.99,0.198 10 false SUB R/B NO. 1 6.25,7.792 6.865,7.99 0.615,0.198 10 false STA2 6.25,5.302 6.865,5.5 0.615,0.198 10 false GND2 6.25,6.146 6.865,6.344 0.615,0.198 10 false GND1 6.25,6.969 6.865,7.167 0.615,0.198 10 false DGND 0.417,8.073 1.49,8.271 1.073,0.198 10 false Battery 1.458,8.396 3.906,8.594 2.448,0.198 10 false Starter Assembly 1.521,7.073 1.677,7.271 0.156,0.198 10 false B 2.25,7.479 2.708,7.677 0.458,0.198 10 false SL2 2.302,6.688 2.615,6.885 0.313,0.198 10 false ST 5.104,8.271 5.26,8.469 0.156,0.198 10 false F 6.083,8.219 7.156,8.656 1.073,0.438 10 false Engine Stop and Start ECU 5.865,0.729 6.323,0.927 0.458,0.198 10 false B38 5.875,1.177 6.333,1.375 0.458,0.198 10 false B38 5.885,1.615 6.344,1.813 0.458,0.198 10 false B38 5.885,2.688 6.344,2.885 0.458,0.198 10 false B38 5.875,3.635 6.333,3.833 0.458,0.198 10 false B37 5.875,4.125 6.333,4.323 0.458,0.198 10 false B37 5.875,5.313 6.333,5.51 0.458,0.198 10 false B37 5.969,0.531 6.281,0.729 0.313,0.198 10 false 17 5.979,0.99 6.292,1.188 0.313,0.198 10 false 21 6.021,1.427 6.177,1.625 0.156,0.198 10 false 7 4.063,1.792 4.521,1.99 0.458,0.198 10 false B36 6.042,2.458 6.198,2.656 0.156,0.198 10 false 1 6,3.427 6.156,3.625 0.156,0.198 10 false 3 6,3.906 6.156,4.104 0.156,0.198 10 false 1 6.031,5.104 6.188,5.302 0.156,0.198 10 false 2 5.865,6.177 6.323,6.375 0.458,0.198 10 false B37 5.865,6.979 6.323,7.177 0.458,0.198 10 false B38 5.865,7.813 6.323,8.01 0.458,0.198 10 false B38 6.01,5.969 6.167,6.167 0.156,0.198 10 false 8 6.021,6.792 6.177,6.99 0.156,0.198 10 false 6 6,7.625 6.313,7.823 0.313,0.198 10 false 23 2.635,1.052 2.792,1.25 0.156,0.198 10 false 5 1.719,1.323 1.875,1.521 0.156,0.198 10 false 4 1.646,1.938 2.104,2.135 0.458,0.198 10 false C34 2.542,3.167 3.917,3.365 1.375,0.198 10 false EFI NO. 2 5.01,1.51 5.167,1.708 0.156,0.198 10 false + 4.604,1.51 4.76,1.708 0.156,0.198 10 false E 4.427,1.479 4.583,1.677 0.156,0.198 10 false 1 5.188,1.5 5.344,1.698 0.156,0.198 10 false 2 2.573,6.698 3.031,6.896 0.458,0.198 10 false C52 1.177,7.083 1.635,7.281 0.458,0.198 10 false C56 2.573,7.49 3.031,7.688 0.458,0.198 10 false C52 2.656,6.521 2.813,6.719 0.156,0.198 10 false 2 2.656,7.292 2.813,7.49 0.156,0.198 10 false 1 1.26,6.896 1.417,7.094 0.156,0.198 10 false 1 4.01,7.385 4.167,7.583 0.156,0.198 10 false 3 4.74,7.396 4.896,7.594 0.156,0.198 10 false 5 4,7.708 4.156,7.906 0.156,0.198 10 false 1 4.76,7.719 4.917,7.917 0.156,0.198 10 false 2

A488189E01
5.406,5.125 7.156,5.406 1.75,0.281 10 false Engine Stop and Start ECU 6.021,3.49 6.635,3.688 0.615,0.198 10 false CANH 6.021,3.99 6.635,4.188 0.615,0.198 10 false CANL 1.927,2.844 2.385,3.042 0.458,0.198 10 false STA 1.813,2.375 2.427,2.573 0.615,0.198 10 false MREL 1.823,1.938 2.281,2.135 0.458,0.198 10 false NSW 1.802,3.5 2.417,3.698 0.615,0.198 10 false CANH 1.844,4 2.458,4.198 0.615,0.198 10 false CANL 1.563,4.75 2.021,4.948 0.458,0.198 10 false ECM 3.448,1 3.604,1.198 0.156,0.198 10 false D 4.031,1.01 4.188,1.208 0.156,0.198 10 false E 4.615,1.01 4.771,1.208 0.156,0.198 10 false F 2.313,1.958 2.771,2.156 0.458,0.198 10 false C37 2.344,2.385 2.656,2.583 0.313,0.198 10 false B1 2.344,2.854 2.656,3.052 0.313,0.198 10 false B1 2.365,1.76 2.521,1.958 0.156,0.198 10 false 7 2.365,2.188 2.521,2.385 0.156,0.198 10 false 3 2.333,2.646 2.646,2.844 0.313,0.198 10 false 34 2.333,3.5 2.646,3.698 0.313,0.198 10 false B1 2.333,4.01 2.646,4.208 0.313,0.198 10 false B1 2.344,3.313 2.656,3.51 0.313,0.198 10 false 18 2.344,3.813 2.656,4.01 0.313,0.198 10 false 17 5.656,3.51 6.115,3.708 0.458,0.198 10 false I57 5.656,4.01 6.115,4.208 0.458,0.198 10 false I57 5.74,3.302 6.052,3.5 0.313,0.198 10 false 13 5.74,3.813 6.052,4.01 0.313,0.198 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations, total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CRANKING
a.

Turn the ignition switch START and check that the engine cranks.


Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

2.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))

B

15.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))
2.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))
a.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter(Hood Close).

Powertrain > Stop and Start > Active Test
Tester Display
Starter(Hood Close)
50004 392 42017

b.

Check whether the engine cranks while the Active Test "Starter" is being performed.

HINT:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Proceed to
OK
NG



OK

3.CHECK VEHICLE CONTROL HISTORY (SFI SYSTEM)

NG

14.CHECK HARNESS AND CONNECTOR (STA SIGNAL)
3.CHECK VEHICLE CONTROL HISTORY (SFI SYSTEM)
a.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

b.

Check the vehicle control history (RoB).

Result:
Result Proceed to
SFI system Vehicle Control History (RoB) is not output A
Engine Difficult to Start is output B
Result other than Engine Difficult to Start is output C


HINT:
·

If the value of "Cranking Time" is approximately 1.5 seconds, the stop and start control system or starter system may be malfunctioning.

·

If the value of "Cranking Time" is small (approximately 0.5 seconds or less: the minimum value varies depending on the model), the SFI system may be malfunctioning.

·

The Data List item "Cranking Time" indicates the length of time starter operation is requested by the engine stop and start ECU. If the engine speed exceeds the specified value, the engine stop and start ECU cancels its start request.





A

5.CHECK VEHICLE CONTROL HISTORY

B

4.CHECK VEHICLE CONTROL HISTORY (SFI SYSTEM)

C

4.CHECK VEHICLE CONTROL HISTORY (SFI SYSTEM)
a.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

b.

Select Engine Difficult to Start from the Vehicle Control History to display the data from the time of control.


c.

Check the output data.

HINT:
·

Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.

·

As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.




Result:
Result Proceed to
Engine speed does not rise to approximately 300 rpm (Starter does not rotate) A
Engine speed rises to approximately 300 rpm (Starter rotates) B



A

5.CHECK VEHICLE CONTROL HISTORY

B

5.CHECK VEHICLE CONTROL HISTORY
a.

Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).

Powertrain > Stop and Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 392 55

b.

Select a vehicle control history item to display the data from the time of control.


c.

Check the output data.

Result:
Tester Display Result Proceed to
Engine Stall History during Stop&Start (Collision or Battery Voltage Low) Yes A
Engine Stall History during Engine Starting (Collision) Yes
Engine Start Fail Yes B
Vehicle control history item is not output or No is displayed for the results of all of the freeze frame data above




A

6.CHECK VEHICLE CONDITION (COLLISION HISTORY)

B

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1, ST NO. 2 RELAY)
6.CHECK VEHICLE CONDITION (COLLISION HISTORY)
a.

Check if the vehicle was in a collision when the engine stalled.

Result:
Result Proceed to
Vehicle was in collision when engine stalled A
Vehicle was not in collision when engine stalled B


HINT:

When "Engine Stall History during Stop&Start (Collision or Battery Voltage Low)" or "Engine Stall History during Engine Starting (Collision)" is stored:

This may have been stored because the vehicle was in a collision or a collision detection signal was input while stop and start control was operating.




A

END (ENGINE STALLED BECAUSE COLLISION DETECTION SIGNAL WAS RECEIVED)

B

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1, ST NO. 2 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Disconnect the park/neutral position switch assembly connector.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B38)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B38-21 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
B38-23 (STA2) - ST NO. 2 relay terminal 2 Always Below 1 Ω
B38-21 (STA) - Body ground Always 10 kΩ or higher
ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher
B38-23 (STA2) - Body ground Always 10 kΩ or higher
ST NO. 2 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω
ST NO. 2 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BATTERY)
a.

Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly


b.
A488379C01
0.125,0.073 0.438,0.271 0.313,0.198 10 false *1 2.323,2.365 2.635,2.563 0.313,0.198 10 false *a 2.292,1.323 2.604,1.521 0.313,0.198 10 false *b
*1 NO. 2 Engine Room Relay Block and Junction Block Assembly
*a ST NO. 1 Relay Terminal
*b ST NO. 2 Relay Terminal


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 5 - Body ground Always 9.5 to 14 V
ST NO. 2 relay terminal 5 - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)
a.
A483989C01
0.448,0.208 0.76,0.406 0.313,0.198 10 false *1 2.875,0.552 3.188,0.75 0.313,0.198 10 false *a
*1 Starter Assembly
*a C56-1 (B)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C56)Location & Routing

Click Connector(C56)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

C56-1 (B) - Body ground Always 9.5 to 14 V


NOTICE:

Before performing this step, check that the starter assembly connector C56 is not disconnected or loose.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C52)Location & Routing

Click Connector(C52)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

ST NO. 1 relay terminal 3 - C52-2 (ST) Always Below 1 Ω
ST NO. 2 relay terminal 3 - C52-1 (SL2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)


Result:
Proceed to
OK
NG



OK

13.INSPECT STARTER ASSEMBLY

NG

REPLACE RELAY (ST NO. 1, ST NO. 2 RELAY)

13.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



NG

14.CHECK HARNESS AND CONNECTOR (STA SIGNAL)
a.

Disconnect the engine stop and start ECU connectors.

A456121C61
3.26,0.094 3.646,0.365 0.385,0.271 3.698,0.823 3.969,1.51 true 3.354,0.927 3.188,1.49 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 3.344,0.156 3.958,0.354 0.615,0.198 10 false B38 3.021,1.542 3.635,1.74 0.615,0.198 10 false STA 3.854,1.542 4.469,1.74 0.615,0.198 10 false DGND
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



b.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B38)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B38-21 (STA) - B38-6 (DGND) Cranking commanded via Active Test item Starter(Hood Close) 6 to 14 V


HINT:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND AND START ECU - ST NO. 1 RELAY)

NG

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



15.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter(Hood Close).

Powertrain > Stop and Start > Active Test
Tester Display
Starter(Hood Close)
50004 392 42017

e.

Check whether the engine cranks while the Active Test "Starter" is being performed.

NOTICE:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

16.READ VALUE USING GTS (NEUTRAL SWITCH)

B

21.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)
16.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 392 202

b.

In accordance with the display on the GTS, read the Data List.

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in P or N ON
Shift lever not in P or N OFF



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU, PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

19.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU, PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the engine stop and start ECU connector.



Result:
Proceed to
OK
NG



OK

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.

Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B38)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B38-17 (CLL) - Body ground Engine started using ignition switch (ignition switch turned to START) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

19.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay from the NO. 2 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I40)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I40-10 (STAR) - ST NO. 1 relay terminal 2 Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)
a.

Connect an oscilloscope to the STA, STA2 and DGND terminals of the engine stop and start ECU connector.

A471731C09
3.188,0.615 3.708,0.844 0.521,0.229 4.167,0.583 4,0.583 4,0.583 3.75,1.208 true 3.427,1.344 3.354,2.208 true 3.271,1.323 2.313,2.281 false 3.313,0.646 3.771,0.844 0.458,0.198 10 false B38 4.219,0.51 4.833,0.708 0.615,0.198 10 false DGND 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 3.229,2.26 3.688,2.458 0.458,0.198 10 false STA 2.135,2.344 2.594,2.542 0.458,0.198 10 false STA2
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.
A285702E12
0.042,0.677 0.5,0.875 0.458,0.198 10 false STA 0.042,1.281 0.5,1.479 0.458,0.198 10 false STA2 1.156,1.781 3.146,1.979 1.99,0.198 10 false 0.03 to 0.06 seconds 0.031,0.854 1.865,1.052 1.833,0.198 10 false (ST NO. 1 Relay) 0.031,1.448 1.865,1.646 1.833,0.198 10 false (ST NO. 2 Relay)

Check the waveform immediately after turning the ignition switch to START.

Item Condition
Tester Connection B38-21 (STA) - B38-6 (DGND)
B38-23 (STA2) - B38-6 (DGND)
Condition Engine started by ignition switch operation

Result:
Result Proceed to
Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: between 0.03 and 0.06 seconds A
Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: not between 0.03 and 0.06 seconds B
ST NO. 1 relay turns on and ST NO. 2 relay does not turn on C
ST NO. 1 relay and ST NO. 2 relay do not turn on D


NOTICE:

After replacing the engine stop and start ECU, make sure that the drive plate and ring gear sub-assembly and starter pinion gear are not excessively worn. A malfunction in the delay circuit may cause the drive plate and ring gear sub-assembly or starter pinion gear to be worn or damaged.




A

22.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)

B

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



C

30.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)

D

32.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - ENGINE STOP AND START ECU)
22.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)


Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BATTERY)

NG

REPLACE RELAY (ST NO. 1, ST NO. 2 RELAY)

23.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BATTERY)
a.
A488379C01
0.125,0.073 0.438,0.271 0.313,0.198 10 false *1 2.323,2.365 2.635,2.563 0.313,0.198 10 false *a 2.292,1.323 2.604,1.521 0.313,0.198 10 false *b
*1 NO. 2 Engine Room Relay Block and Junction Block Assembly
*a ST NO. 1 Relay Terminal
*b ST NO. 2 Relay Terminal


Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 5 - Body ground Always 9.5 to 14 V
ST NO. 2 relay terminal 5 - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

24.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C52)Location & Routing

Click Connector(C52)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

ST NO. 1 relay terminal 3 - C52-2 (ST) Always Below 1 Ω
ST NO. 2 relay terminal 3 - C52-1 (SL2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relays from the NO. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)
a.

Remove the ST NO. 2 relay from the NO. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 2 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Remove the ST NO. 1 relay from the NO. 2 engine room relay block and junction block assembly.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B38)Location & Routing

B38-21 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
B38-21 (STA) - Body ground Always 10 kΩ or higher
ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 2 RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the engine stop and start ECU connector.


c.

Remove the ST NO. 2 relay from the NO. 2 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B38)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B38-23 (STA2) - ST NO. 2 relay terminal 2 Always Below 1 Ω
B38-23 (STA2) - Body ground Always 10 kΩ or higher
ST NO. 2 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

29.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B37)Location & Routing

Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B37-1 (BIN2) - Body ground Always 9.5 to 14 V
B37-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B38,I57)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

B38-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
I57-21 (IGR) - Body ground Ignition switch ON 9.5 to 14 V
I57-18 (IGP) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

31.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B37,B38)Location & Routing

Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B37-2 (GND2) - Body ground Always Below 1 Ω
B37-8 (GND1) - Body ground Always Below 1 Ω
B38-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - ENGINE STOP AND START ECU)
a.

Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the park/neutral position switch assembly connector.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B38)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B38-21 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
B38-23 (STA2) - ST NO. 2 relay terminal 2 Always Below 1 Ω
B38-21 (STA) - Body ground Always 10 kΩ or higher
B38-23 (STA2) - Body ground Always 10 kΩ or higher
ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher
ST NO. 2 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



NG

REPAIR OR REPLACE HARNESS OR CONNECTOR