| *A | w/ Telematics Transceiver | - | - |
| *1 | WIRING HARNESS PROTECTOR | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ★ | Precoated part | - | - |
| *A | w/o Audio | *B | w/ Audio |
| *C | for Radio Receiver Type | *D | for Radio and Display Type |
| *E | w/ Multi-display | *F | w/o Multi-display |
| *G | for 7 Inch Display | *H | for 9 Inch Display |
| *I | except 2 Speakers | *J | for Side |
| *K | for Center | *L | for 10 Speakers |
| *M | except 10 Speakers | *N | for 14 Speakers |
| *O | w/ Headup Display | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 17 | AIR CONDITIONING PANEL ASSEMBLY | - | - | - | - |
| 18 | NO. 1 DEFROSTER NOZZLE GARNISH | 55981 | - | - | - |
| 19 | INSTRUMENT CLUSTER FINISH PANEL COVER | 55423B | - | - | - |
| 20 | NO. 1 SPEAKER OPENING COVER ASSEMBLY | 55510F | - | - | - |
| 21 | NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY | 55409F | - | - | - |
| 22 | NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY | 55408F | - | - | - |
| 23 | FRONT PILLAR GARNISH ASSEMBLY LH | 62212B | - | - | - |
| 24 | FRONT PILLAR GARNISH ASSEMBLY RH | 62211U | - | - | - |
| 25 | FRONT ASSIST GRIP ASSEMBLY | 74620G | - | - | - |
| 26 | ASSIST GRIP PLUG | 74617A | - | - | - |
| *A | w/o Multi-display | *B | w/ Multi-display |
| *C | for Type A | *D | for Type B |
| *E | w/ Curtain Shield Airbag | - | - |
| ● | Non-reusable part | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
1.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
When installing a new instrument panel safety pad assembly:
Immediately before installing the instrument panel safety pad sub-assembly, twist and cut off the portion as shown in the illustration.
|
Install in this Direction | - | - |
Install the instrument panel safety pad assembly as shown in the illustration.
Do not damage the instrument panel safety pad assembly or vehicle interior.
Make sure that the wire harness does not get caught on anything as it may become damaged.
|
Install in this Direction | - | - |
Attach the guide as shown in the illustration.
Do not damage the instrument panel safety pad assembly or vehicle interior.
Make sure that the wire harness does not get caught on anything as it may become damaged.
Install the 2 clips.
Install the 2 bolts <D>.
Install the nut <E>.
Install the 8 bolts <C>.
| *A | w/ Telematics Transceiver | - | - |
|
Connector |
|
Airbag Connector |
Attach the guide.
Attach the clamp.
Connect the airbag connector.
Refer to How to Connect or Disconnect Airbag Connector:
Connect each connector.
w/ Telematics Transceiver:
Attach the claw to connect the wire harness.
Attach the clamp.
Connect the connector.
58123A 2.INSTALL SHIFT AND SELECT LEVER SUPPORT (w/ Telematics Transceiver)
Clean the bolt hole in the vehicle body.
When reusing the bolt.
1. Clean the threads of the bolt.
2. Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
Install the shift and select lever support with the 4 bolts.
Attach the clamp and connector.
3.INSTALL FLOOR SHIFT LEVER ASSEMBLY (w/ Telematics Transceiver)
84650 4.INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY
45286B 5.INSTALL UPPER STEERING COLUMN COVER
45024 6.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY
45100 7.INSTALL STEERING WHEEL ASSEMBLY
55414A 10.INSTALL INSTRUMENT CLUSTER FINISH PANEL END (w/ Headup Display)
55406B 11.INSTALL CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-display)
55522B 12.INSTALL RADIO TUNER OPENING COVER (w/o Audio)
55422C 13.INSTALL CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL (w/o Audio)
14.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Audio, for Radio Receive Type)
15.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Audio, for Radio and Display Type)
86110B 16.INSTALL MULTI-DISPLAY ASSEMBLY (w/ Audio, Multi-display)
17.INSTALL AIR CONDITIONING PANEL ASSEMBLY
55981 18.INSTALL NO. 1 DEFROSTER NOZZLE GARNISH
55423B 19.INSTALL INSTRUMENT CLUSTER FINISH PANEL COVER (w/o Multi-display)
55510F 20.INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY (w/ Multi-display)
55409F 21.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
55408F 22.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
62212B 23.INSTALL FRONT PILLAR GARNISH ASSEMBLY LH
62211U 24.INSTALL FRONT PILLAR GARNISH ASSEMBLY RH
74620G 25.INSTALL FRONT ASSIST GRIP ASSEMBLY
74617A 26.INSTALL ASSIST GRIP PLUG
55660 27.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
55320 28.INSTALL LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY
55443A 29.INSTALL INSTRUMENT PANEL BOX DOOR COVER
53601 31.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
77306 32.CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
55446A 34.INSTALL NO. 1 SWITCH HOLE BASE
55650 35.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
83100 36.INSTALL COMBINATION METER ASSEMBLY
55404D 37.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
55312 38.INSTALL LOWER INSTRUMENT PANEL
55432D 39.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
55318F 40.INSTALL NO. 2 INSTRUMENT SIDE PANEL
55317E 41.INSTALL NO. 1 INSTRUMENT SIDE PANEL
62112 42.INSTALL COWL SIDE TRIM BOARD LH
62111C 43.INSTALL COWL SIDE TRIM BOARD RH
67914B 44.INSTALL FRONT DOOR SCUFF PLATE LH
67913B 45.INSTALL FRONT DOOR SCUFF PLATE RH
55607 46.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55606 47.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
48.INSTALL FRONT CONSOLE BOX
w/ Cool Box:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX (w/ Cool Box)>INSTALLATION
w/o Cool Box:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX (w/o Cool Box)>INSTALLATION
49.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
for 1GR-FE:
for F33A-FTV:
for V35A-FTS:
51. PERFORM DIAGNOSTIC SYSTEM CHECK
53. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART