Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2022.11
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150718  Turn Signal Light Circuit Current Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
B150718 Turn Signal Light Circuit Current Below Threshold
Diagnosis Condition:

Battery voltage is 10 V or more


Malfunction Status:
·

Open in front turn signal light circuit

·

Open in side turn signal light circuit

·

Open in rear turn signal light circuit


·

Headlight unit assembly (w/ Headlight ECU)

·

Headlight housing (w/o Headlight ECU)

·

Headlight lens sub-assembly

·

Headlight ECU sub-assembly (w/ Headlight ECU)

·

Side turn signal light assembly

·

Outer mirror retractor

·

Outer mirror control ECU assembly (w/ Outer Mirror Control ECU Assembly)

·

Rear combination light cord

·

Rear combination light assembly

·

Rear light socket and wire (for Sequential Type Turn Signal Light)

·

Rear light assembly (for Sequential Type Turn Signal Light)

·

Headlight cord (w/ Headlight ECU for RHD)

·

Harness or connector

·

Combination meter assembly



WIRING DIAGRAM

B604975E04
0.906,2.354 3.198,2.552 2.292,0.198 10 false Headlight Unit Assembly RH 0.448,1.885 2.74,2.083 2.292,0.198 10 false Headlight Lens Sub-assembly RH 3.417,2.563 4.708,2.969 1.292,0.406 10 false Headlight ECU Sub-assembly RH 3.323,1.083 5.615,1.281 2.292,0.198 10 false A 3.313,1.583 5.604,1.781 2.292,0.198 10 false A 3.281,1.406 5.573,1.604 2.292,0.198 10 false 20 3.333,0.906 5.625,1.104 2.292,0.198 10 false 6 4.677,1.427 6.969,1.625 2.292,0.198 10 false 12 4.677,0.906 6.969,1.104 2.292,0.198 10 false 11 4.26,1.115 6.552,1.313 2.292,0.198 10 false TNS 4.26,1.625 6.552,1.823 2.292,0.198 10 false GND 4.667,1.615 5.104,2.021 0.438,0.406 10 false B7 4.667,1.104 5.104,1.51 0.438,0.406 10 false B7 6.052,1.052 6.49,1.458 0.438,0.406 10 false LR 5.771,0.927 6.208,1.333 0.438,0.406 10 false 5 5.771,7 7.094,7.573 1.323,0.573 10 false I6 5.75,7.177 7.073,7.75 1.323,0.573 10 false Combination Meter Assembly 2.635,5.438 4.927,5.635 2.292,0.198 10 false Headlight Housing RH 4.656,4.469 5.094,4.875 0.438,0.406 10 false B6 0.094,0.135 2.604,0.406 2.51,0.271 12 false w/ Headlight ECU for LHD: 0.115,3.406 1.604,3.615 1.49,0.208 12 false w/o Headlight ECU: 4.219,4.833 4.542,5.042 0.323,0.208 10 false GND 4.427,4.354 6.719,4.552 2.292,0.198 10 false B 4.708,4.792 7,4.99 2.292,0.198 10 false 7 4.698,4.292 4.823,4.49 0.125,0.198 10 false 8 0.24,5.427 2.531,5.625 2.292,0.198 10 false Headlight Lens Sub-assembly RH 2.438,4.292 2.563,4.49 0.125,0.198 10 false 1 2.406,4.792 4.698,4.99 2.292,0.198 10 false 4 2.406,4.458 2.729,4.667 0.323,0.208 10 false B 2.396,4.958 2.719,5.167 0.323,0.208 10 false B 4.667,4.958 5.104,5.365 0.438,0.406 10 false B6

B671778E01
0.125,0.156 4.708,0.396 4.583,0.24 12 false w/ Headlight ECU for RHD: 0.344,1.885 1.604,2.271 1.26,0.385 10 false Headlight Lens Sub-assembly RH 2.042,2.854 3.292,3.219 1.25,0.365 10 false Headlight ECU Sub-assembly RH 5.927,3.833 6.24,4.031 0.313,0.198 10 false I6 5.917,3.99 7.094,4.354 1.177,0.365 10 false Combination Meter Assembly 3.51,2.417 6.115,2.615 2.604,0.198 10 false Headlight Cord RH 1.938,1.094 2.094,1.292 0.156,0.198 10 false B 1.927,1.594 2.083,1.792 0.156,0.198 10 false B 1.917,1.385 2.229,1.583 0.313,0.198 10 false 20 1.948,0.917 2.104,1.115 0.156,0.198 10 false 6 2.823,0.979 3.281,1.177 0.458,0.198 10 false TNS 2.854,1.469 3.313,1.667 0.458,0.198 10 false GND 3.25,1.094 3.708,1.292 0.458,0.198 10 false B89 3.25,1.594 3.708,1.792 0.458,0.198 10 false B89 4.625,1.094 5.083,1.292 0.458,0.198 10 false BB8 4.625,1.594 5.083,1.792 0.458,0.198 10 false BB9 4.708,1.396 4.865,1.594 0.156,0.198 10 false 1 4.719,0.875 4.875,1.073 0.156,0.198 10 false 7 3.292,0.875 3.604,1.073 0.313,0.198 10 false 11 3.281,1.385 3.594,1.583 0.313,0.198 10 false 12 0.51,2.677 1.406,3.104 0.896,0.427 10 false Headlight Unit Assembly RH

B604976E07
3.417,2.563 4.823,3.031 1.406,0.469 10 false Outer Mirror Control ECU Assembly RH 3.292,1.083 5.583,1.281 2.292,0.198 10 false z9 3.292,1.594 5.583,1.792 2.292,0.198 10 false z9 3.292,1.385 5.583,1.583 2.292,0.198 10 false 12 3.302,0.906 5.594,1.104 2.292,0.198 10 false 16 4.708,1.438 7,1.635 2.292,0.198 10 false 7 4.677,0.917 6.969,1.115 2.292,0.198 10 false 11 4.219,1.083 6.51,1.281 2.292,0.198 10 false TRNI 4.229,1.604 6.521,1.802 2.292,0.198 10 false GND 4.667,1.604 5.104,2.01 0.438,0.406 10 false M1 4.656,1.094 5.094,1.5 0.438,0.406 10 false M1 4.635,4.865 5.292,5.281 0.656,0.417 10 false 4 4.417,4.844 4.833,5.25 0.417,0.406 10 false - 4.406,4.354 4.844,4.76 0.438,0.406 10 false B 2.552,5.396 2.885,5.583 0.333,0.188 10 false M21 5.76,6.917 7.083,7.49 1.323,0.573 10 false Combination Meter Assembly 2.552,5.542 4.198,5.74 1.646,0.198 10 false Outer Mirror Retractor RH 4.646,4.375 5.083,4.781 0.438,0.406 10 false 5 0.188,5.417 2.458,5.708 2.271,0.292 10 false Side Turn Signal Light Assembly RH 0.104,2.396 1.49,2.948 1.385,0.552 10 false Side Turn Signal Light Assembly RH 1.677,2.396 3.292,2.615 1.615,0.219 10 false Outer Mirror Retractor RH 0.104,0.125 3.323,0.5 3.219,0.375 12 false w/ Outer Mirror Control ECU Assembly: 0.083,3.406 3.302,3.781 3.219,0.375 12 false w/o Outer Mirror Control ECU Assembly: 3.583,1.094 5.875,1.292 2.292,0.198 10 false TRN+ 3.583,1.604 5.875,1.802 2.292,0.198 10 false TRN- 5.75,6.74 6.083,6.927 0.333,0.188 10 false I6

B604977E04
0.906,2.354 3.198,2.552 2.292,0.198 10 false Headlight Unit Assembly LH 0.458,1.865 2.75,2.063 2.292,0.198 10 false Headlight Lens Sub-assembly LH 3.406,2.573 4.698,2.979 1.292,0.406 10 false Headlight ECU Sub-assembly LH 3.323,1.083 5.615,1.281 2.292,0.198 10 false A 2.448,4.469 4.74,4.667 2.292,0.198 10 false B 3.281,1.406 5.573,1.604 2.292,0.198 10 false 20 3.333,0.906 5.625,1.104 2.292,0.198 10 false 6 4.677,1.427 6.969,1.625 2.292,0.198 10 false 12 4.677,0.906 6.969,1.104 2.292,0.198 10 false 11 4.26,1.115 6.552,1.313 2.292,0.198 10 false TNS 4.26,1.625 6.552,1.823 2.292,0.198 10 false GND 4.667,1.594 5.104,2 0.438,0.406 10 false B4 4.667,1.083 5.104,1.49 0.438,0.406 10 false B4 6.052,1.052 6.49,1.458 0.438,0.406 10 false LL 5.75,0.927 6.188,1.333 0.438,0.406 10 false 14 5.958,6.781 6.167,6.979 0.208,0.198 10 false I6 5.958,6.958 7.156,7.333 1.198,0.375 10 false Combination Meter Assembly 2.688,5.417 4.979,5.615 2.292,0.198 10 false Headlight Housing LH 0.208,5.406 2.5,5.604 2.292,0.198 10 false Headlight Lens Sub-assembly LH 4.688,4.479 5.125,4.885 0.438,0.406 10 false B3 0.104,0.125 2.698,0.427 2.594,0.302 12 false w/ Headlight ECU for LHD: 0.094,3.396 1.552,3.594 1.458,0.198 12 false w/o Headlight ECU: 4.719,4.302 5.156,4.708 0.438,0.406 10 false 8 4.719,4.802 4.906,4.99 0.188,0.188 10 false 7 4.24,4.833 4.563,5.021 0.323,0.188 10 false GND 4.417,4.354 4.583,4.531 0.167,0.177 10 false B 2.438,4.958 4.729,5.156 2.292,0.198 10 false B 2.458,4.281 2.896,4.688 0.438,0.406 10 false 1 2.458,4.802 2.896,5.208 0.438,0.406 10 false 4 4.656,4.958 5.094,5.365 0.438,0.406 10 false B3 3.302,1.594 5.594,1.792 2.292,0.198 10 false A

B671778E02
0.125,0.156 4.708,0.396 4.583,0.24 12 false w/ Headlight ECU for RHD: 0.344,1.885 1.604,2.271 1.26,0.385 10 false Headlight Lens Sub-assembly LH 2.042,2.854 3.292,3.219 1.25,0.365 10 false Headlight ECU Sub-assembly LH 5.927,3.833 6.24,4.031 0.313,0.198 10 false I6 5.917,3.99 7.094,4.354 1.177,0.365 10 false Combination Meter Assembly 3.51,2.406 6.115,2.604 2.604,0.198 10 false Headlight Cord LH 1.938,1.094 2.094,1.292 0.156,0.198 10 false B 1.927,1.594 2.083,1.792 0.156,0.198 10 false B 1.917,1.385 2.229,1.583 0.313,0.198 10 false 20 1.948,0.917 2.104,1.115 0.156,0.198 10 false 6 2.833,0.979 3.292,1.177 0.458,0.198 10 false TNS 2.854,1.469 3.313,1.667 0.458,0.198 10 false GND 4.698,0.885 4.854,1.083 0.156,0.198 10 false 7 4.708,1.385 4.865,1.583 0.156,0.198 10 false 1 3.25,1.094 3.708,1.292 0.458,0.198 10 false B88 3.25,1.583 3.708,1.781 0.458,0.198 10 false B88 0.479,2.635 1.396,3.063 0.917,0.427 10 false Headlight Unit Assembly LH 4.625,1.094 5.083,1.292 0.458,0.198 10 false BB6 4.625,1.583 5.083,1.781 0.458,0.198 10 false BB7 3.281,0.896 3.594,1.094 0.313,0.198 10 false 11 3.281,1.385 3.594,1.583 0.313,0.198 10 false 12

B604976E08
3.406,2.563 4.885,2.969 1.479,0.406 10 false Outer Mirror Control ECU Assembly LH 3.292,1.406 5.583,1.604 2.292,0.198 10 false 12 3.302,0.896 5.594,1.094 2.292,0.198 10 false 16 4.719,1.438 7.01,1.635 2.292,0.198 10 false 7 4.677,0.917 6.969,1.115 2.292,0.198 10 false 11 4.24,1.094 6.531,1.292 2.292,0.198 10 false TRNI 4.219,1.604 6.51,1.802 2.292,0.198 10 false GND 4.677,1.594 4.917,1.823 0.24,0.229 10 false N1 4.667,1.094 5.104,1.5 0.438,0.406 10 false N1 4.635,4.885 5.292,5.302 0.656,0.417 10 false 4 4.417,4.833 4.833,5.24 0.417,0.406 10 false - 4.406,4.354 4.844,4.76 0.438,0.406 10 false B 2.521,5.396 2.833,5.552 0.313,0.156 10 false N21 5.75,6.906 7.073,7.479 1.323,0.573 10 false Combination Meter Assembly 2.51,5.542 4.135,5.76 1.625,0.219 10 false Outer Mirror Retractor LH 4.646,4.375 5.083,4.781 0.438,0.406 10 false 5 0.167,5.417 2.438,5.708 2.271,0.292 10 false Side Turn Signal Light Assembly LH 0.104,2.396 1.469,2.792 1.365,0.396 10 false Side Turn Signal Light Assembly LH 3.25,1.583 3.583,1.792 0.333,0.208 10 false z10 1.677,2.385 3.26,2.583 1.583,0.198 10 false Outer Mirror Retractor LH 0.094,0.104 3.667,0.615 3.573,0.51 12 false w/ Outer Mirror Control ECU Assembly: 0.104,3.427 3.677,3.938 3.573,0.51 12 false w/o Outer Mirror Control ECU Assembly: 3.26,1.083 3.542,1.281 0.281,0.198 10 false z10 3.583,1.094 5.875,1.292 2.292,0.198 10 false TRN+ 3.583,1.615 5.875,1.813 2.292,0.198 10 false TRN- 5.75,6.74 6.063,6.896 0.313,0.156 10 false I6

B608402E01
5.792,7.688 6.938,8.438 1.146,0.75 10 false Combination Meter Assembly 0.271,2.781 2.458,3.323 2.188,0.542 10 false Rear Light Assembly RH 2.365,2.719 5.344,2.979 2.979,0.26 10 false g1 2.323,5.531 5.688,5.729 3.365,0.198 10 false b2 0.24,5.51 1.802,5.885 1.563,0.375 10 false Rear Combination Light Assembly RH 1.948,7.938 5.313,8.135 3.365,0.198 10 false b2 0.25,7.948 1.781,8.323 1.531,0.375 10 false Rear Combination Light Assembly RH 5.813,7.51 6.781,8.156 0.969,0.646 10 false I6 4.375,1.281 5.635,1.688 1.26,0.406 10 false 3 6,1.365 7.156,1.771 1.156,0.406 10 false TRNR 5.771,1.26 6.927,1.667 1.156,0.406 10 false 2 5.729,0.885 6.885,1.292 1.156,0.406 10 false 12 4.188,1.271 5.448,1.677 1.26,0.406 10 false B 3.948,0.927 5.208,1.333 1.26,0.406 10 false TRN6 5.99,1.01 7.146,1.417 1.156,0.406 10 false SYC1 3.938,4.125 4.969,4.323 1.031,0.198 10 false TRN1 3.927,3.667 5.208,4.01 1.281,0.344 10 false TRN2 3.948,1.615 5.281,1.99 1.333,0.375 10 false TRN4 3.948,1.958 6.5,2.219 2.552,0.26 10 false TRN3 4.375,4.146 5.583,4.583 1.208,0.438 10 false 3 4.385,3.656 6.01,4.021 1.625,0.365 10 false 2 4.375,1.979 6.042,2.177 1.667,0.198 10 false 1 4.375,1.625 5.854,1.792 1.479,0.167 10 false 2 4.156,5.042 6.208,5.385 2.052,0.344 10 false E 4.385,5.052 5.99,5.354 1.604,0.302 10 false 4 4.375,0.906 5.635,1.313 1.26,0.406 10 false 8 4.01,4.615 5.708,5 1.698,0.385 10 false TRN 4.375,4.573 5.5,4.813 1.125,0.24 10 false 1 3.292,6.885 6.656,7.083 3.365,0.198 10 false TRN 3.469,7.354 6.833,7.552 3.365,0.198 10 false E 3.688,7.365 7.052,7.563 3.365,0.198 10 false 4 3.667,6.875 7.031,7.073 3.365,0.198 10 false 1 0.135,6.167 5.448,6.552 5.313,0.385 12 false except Sequential Type Turn Signal Light (w/ Turn Light LED Type): 0.198,0.167 3.563,0.365 3.365,0.198 12 false for Sequential Type Turn Signal Light: 2.323,5.677 4.479,6.198 2.156,0.521 10 false Rear Combination Light Cord RH 1.927,8.094 4.146,8.5 2.219,0.406 10 false Rear Combination Light Cord RH 2.354,2.885 4.542,3.417 2.188,0.531 10 false Rear Light Socket and Wire RH 4.396,2.333 6.031,2.563 1.635,0.229 10 false 4 4.177,2.333 5.948,2.635 1.771,0.302 10 false E

B612066E02
5.302,3.396 7.156,3.656 1.854,0.26 10 false Combination Meter Assembly 0.313,2.281 0.625,2.479 0.313,0.198 10 false b2 0.302,2.458 3.563,2.802 3.26,0.344 10 false Rear Combination Light Cord RH 0.26,0.417 5.313,0.823 5.052,0.406 12 false except Sequential Type Turn Signal Light (w/ Turn Light Bulb Type): 3.01,1.26 3.5,1.479 0.49,0.219 10 false TRN 3.208,1.698 3.698,1.917 0.49,0.219 10 false E 3.417,1.229 3.729,1.427 0.313,0.198 10 false 1 3.427,1.75 3.74,1.948 0.313,0.198 10 false 4 5.323,3.208 5.635,3.406 0.313,0.198 10 false I6

B608403E04
5.802,7.865 6.948,8.615 1.146,0.75 10 false Combination Meter Assembly 0.25,3.042 2.438,3.583 2.188,0.542 10 false Rear Light Assembly LH 2.375,3 5.354,3.26 2.979,0.26 10 false g2 2.323,5.802 5.688,6 3.365,0.198 10 false c2 0.26,5.813 1.823,6.188 1.563,0.375 10 false Rear Combination Light Assembly LH 1.948,8.198 5.313,8.396 3.365,0.198 10 false c2 0.25,8.219 1.781,8.594 1.531,0.375 10 false Rear Combination Light Assembly LH 5.802,7.708 6.771,8.354 0.969,0.646 10 false I6 4.385,1.563 5.646,1.969 1.26,0.406 10 false 3 6,1.677 7.156,2.083 1.156,0.406 10 false TRNL 5.781,1.552 6.938,1.958 1.156,0.406 10 false 1 4.188,1.563 5.448,1.969 1.26,0.406 10 false B 3.948,1.208 5.208,1.615 1.26,0.406 10 false TRN6 3.969,4.417 5,4.615 1.031,0.198 10 false TRN1 3.979,3.969 5.26,4.313 1.281,0.344 10 false TRN2 3.948,1.927 5.281,2.302 1.333,0.375 10 false TRN4 3.948,2.281 6.5,2.542 2.552,0.26 10 false TRN3 4.417,4.438 5.625,4.875 1.208,0.438 10 false 3 4.417,3.969 6.042,4.333 1.625,0.365 10 false 2 4.396,2.281 6.063,2.479 1.667,0.198 10 false 1 4.385,1.927 5.865,2.094 1.479,0.167 10 false 2 4.177,5.365 6.229,5.708 2.052,0.344 10 false E 4.396,5.354 6,5.656 1.604,0.302 10 false 4 4.385,1.188 5.646,1.594 1.26,0.406 10 false 8 4.021,4.885 5.719,5.271 1.698,0.385 10 false TRN 4.396,4.885 5.521,5.125 1.125,0.24 10 false 1 3.292,7.177 6.656,7.375 3.365,0.198 10 false TRN 3.469,7.677 6.833,7.875 3.365,0.198 10 false E 3.688,7.667 7.052,7.865 3.365,0.198 10 false 4 3.688,7.177 7.052,7.375 3.365,0.198 10 false 1 0.156,6.458 5.219,6.823 5.063,0.365 12 false except Sequential Type Turn Signal Light (w/ Turn Light LED Type): 0.198,0.406 3.563,0.604 3.365,0.198 12 false for Sequential Type Turn Signal Light: 2.323,5.927 4.479,6.448 2.156,0.521 10 false Rear Combination Light Cord LH 1.948,8.354 4.167,8.76 2.219,0.406 10 false Rear Combination Light Cord LH 2.344,3.167 4.531,3.698 2.188,0.531 10 false Rear Light Socket and Wire LH 4.396,2.594 6.031,2.823 1.635,0.229 10 false 4 4.177,2.604 5.948,2.906 1.771,0.302 10 false E

B612067E02
5.302,3.458 7.156,3.719 1.854,0.26 10 false Combination Meter Assembly 0.313,2.281 0.625,2.479 0.313,0.198 10 false c2 0.302,2.458 3.563,2.802 3.26,0.344 10 false Rear Combination Light Cord LH 0.26,0.417 5.313,0.823 5.052,0.406 12 false except Sequential Type Turn Signal Light (w/ Turn Light Bulb Type): 3.01,1.26 3.5,1.479 0.49,0.219 10 false TRN 3.208,1.698 3.698,1.917 0.49,0.219 10 false E 3.417,1.229 3.729,1.427 0.313,0.198 10 false 1 3.427,1.75 3.74,1.948 0.313,0.198 10 false 4 5.302,3.25 5.615,3.448 0.313,0.198 10 false I6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the bulbs before performing the following procedure. (w/ Turn Light Bulb Type)


w/ Headlight ECU:

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>REGISTRATION

·

When the combination meter assembly is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Front turn signal light LH and side turn signal light LH do not blink. A
Front turn signal light RH and side turn signal light RH do not blink. B
Front turn signal light LH does not blink. C
Front turn signal light RH does not blink. D
Side turn signal light LH does not blink. E
Side turn signal light RH does not blink. F
Rear turn signal light LH does not blink. G
Rear turn signal light RH does not blink. H



A

2.CHECK VEHICLE TYPE

B

6.CHECK VEHICLE TYPE

C

10.CHECK VEHICLE TYPE

D

20.CHECK VEHICLE TYPE

E

30.CHECK VEHICLE TYPE

F

36.CHECK VEHICLE TYPE

G

42.CHECK VEHICLE TYPE

H

62.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Headlight ECU for LHD A
w/ Headlight ECU for RHD B
w/o Headlight ECU C



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)

B

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT CORD LH)

C

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT HOUSING LH)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B4 headlight ECU sub-assembly LH connector.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT CORD LH)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the BB6 headlight cord LH connector.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT HOUSING LH)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B3 headlight housing LH connector.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Headlight ECU for LHD A
w/ Headlight ECU for RHD B
w/o Headlight ECU C



A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT CORD RH)

C

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT HOUSING RH)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT CORD RH)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the BB8 headlight cord RH connector.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT HOUSING RH)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B6 headlight housing RH connector.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Headlight ECU for LHD A
w/ Headlight ECU for RHD B
w/o Headlight ECU C



A

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)

B

14.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT HOUSING LH AND BODY GROUND)
11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B4 headlight ECU sub-assembly LH connector.



Result:
Proceed to
OK
NG



OK

12.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.
B612074C01
1.479,2.75 2,3.01 0.521,0.26 1.479,0.24 2,0.5 0.521,0.26 1.583,3.781 2.25,2.906 2.25,2.906 2.49,2.906 true 1.688,0.313 1.844,0.51 0.156,0.198 10 false A 1.656,2.802 2.031,3.052 0.375,0.25 10 false I6 0.323,0.563 0.646,0.76 0.323,0.198 10 false *a 2.573,2.792 2.969,3.031 0.396,0.24 10 false LL 0.354,2.781 0.698,2.938 0.344,0.156 10 false *b
*a Component with harness connected
(Headlight ECU Sub-assembly LH)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Remove the headlight ECU sub-assembly LH as a unit with the connectors still connected.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Disconnect the I6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

A-6 - I6-14 (LL) Always Below 1 Ω
A-20 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HEADLIGHT UNIT ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

13.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Remove the headlight unit assembly LH and RH.


b.

Interchange the headlight unit assembly LH with RH and connect the connectors.


c.

Operate the turn signal switch and check that the LH side turn signal light operates normally.

NOTICE:

If the LH side front turn signal light operates normally, return the headlight unit assembly LH and headlight unit assembly RH that were interchanged in a previous step back to their original conditions so that a component of the headlight unit assembly LH can be inspected in the next step.



Result:
Result Proceed to
LH side front turn signal light operates normally A
Problem symptoms do not change
(LH side front turn signal light does not blink)
B



A

REPLACE HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE HEADLIGHT LENS SUB-ASSEMBLY LH

14.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the B88 headlight ECU sub-assembly LH connector.


b.

Disconnect the I6 combination meter assembly connector.



Result:
Proceed to
OK
NG



OK

15.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

17.CHECK HEADLIGHT CORD LH
15.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.
B612074C09
1.479,2.75 2,3.01 0.521,0.26 1.479,0.24 2,0.5 0.521,0.26 1.583,3.781 2.25,2.906 2.25,2.906 2.49,2.906 true 1.688,0.313 1.844,0.51 0.156,0.198 10 false B 1.656,2.802 2.031,3.052 0.375,0.25 10 false I6 0.323,0.563 0.646,0.76 0.323,0.198 10 false *a 0.354,2.781 0.698,2.938 0.344,0.156 10 false *b 2.563,2.833 2.875,3.031 0.313,0.198 10 false LL
*a Component with harness connected
(Headlight ECU Sub-assembly LH)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Remove the headlight ECU sub-assembly LH as a unit with the connectors still connected.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Disconnect the I6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-14 (LL) - B-6 Always Below 1 Ω
B-20 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK HEADLIGHT UNIT ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

16.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Remove the headlight unit assembly LH and RH.


b.

Interchange the headlight unit assembly LH with RH and connect the connectors.


c.

Operate the turn signal switch and check that the LH side turn signal light operates normally.

NOTICE:

If the LH side front turn signal light operates normally, return the headlight unit assembly LH and headlight unit assembly RH that were interchanged in a previous step back to their original conditions so that a component of the headlight unit assembly LH can be inspected in the next step.



Result:
Result Proceed to
LH side front turn signal light operates normally A
Problem symptoms do not change
(LH side front turn signal light does not blink)
B



A

REPLACE HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE HEADLIGHT LENS SUB-ASSEMBLY LH

17.CHECK HEADLIGHT CORD LH
a.

Disconnect the BB6, BB7 and B88 headlight cord LH connectors.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



b.

Measure the resistance according to the value(s) in the table below.

E507307C01
1.375,0.135 1.792,0.406 0.417,0.271 3.854,0.094 4.271,0.365 0.417,0.271 5.792,0.156 6.208,0.427 0.417,0.271 4.521,0.99 4.729,1.313 4.729,1.313 4.885,1.313 true 6.156,1.042 6.365,1.365 6.365,1.365 6.521,1.365 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.469,0.198 1.927,0.396 0.458,0.198 10 false B88 3.938,0.146 4.396,0.344 0.458,0.198 10 false BB6 5.865,0.208 6.323,0.406 0.458,0.198 10 false BB7 4.979,1.229 5.438,1.427 0.458,0.198 10 false TNS 6.604,1.271 7.063,1.469 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Headlight Cord LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB6,B88,BB7)Location & Routing

Click Connector(BB6)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and No. 2 Lamp Wire

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

Click Connector(BB7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and No. 2 Lamp Wire

BB6-7 - B88-11 (TNS) Always Below 1 Ω
BB7-1 - B88-12 (GND) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT HOUSING LH AND BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B3 headlight housing LH connector.



Result:
Proceed to
OK
NG



OK

19.INSPECT HEADLIGHT HOUSING LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT HEADLIGHT HOUSING LH
a.
B611438C01
1.552,1.604 1.969,1.875 0.417,0.271 1.531,0.198 1.969,0.479 0.438,0.281 0.625,0.354 0.938,0.552 0.313,0.198 10 false *a 1.708,0.25 2.021,0.448 0.313,0.198 10 false A 1.708,1.656 2.021,1.854 0.313,0.198 10 false B 0.573,1.677 0.885,1.875 0.313,0.198 10 false *b
*a Component without harness connected
(Headlight Housing LH)
*b Component without harness connected
(to Headlight Lens Sub-assembly LH)


Remove the headlight housing LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-8 - B-1 Always Below 1 Ω
A-7 - B-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LENS SUB-ASSEMBLY LH

NG

20.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Headlight ECU for LHD A
w/ Headlight ECU for RHD B
w/o Headlight ECU C



A

21.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

24.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

28.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT HOUSING RH AND BODY GROUND)
21.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.



Result:
Proceed to
OK
NG



OK

22.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.
B612074C02
1.479,2.75 2,3.01 0.521,0.26 1.479,0.24 2,0.5 0.521,0.26 2.469,3.521 2.719,2.938 2.719,2.938 2.906,2.938 false 1.688,0.313 1.844,0.51 0.156,0.198 10 false A 1.656,2.802 2.031,3.052 0.375,0.25 10 false I6 2.958,2.844 3.208,3.24 0.25,0.396 10 false LR 0.573,0.458 0.823,0.854 0.25,0.396 10 false *a 0.406,2.781 0.656,3.177 0.25,0.396 10 false *b
*a Component with harness connected
(Headlight ECU Sub-assembly RH)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Remove the headlight ECU sub-assembly RH as a unit with the connectors still connected.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Disconnect the I6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

A-6 - I6-5 (LR) Always Below 1 Ω
A-20 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

23.CHECK HEADLIGHT UNIT ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

23.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Remove the headlight unit assembly LH and RH.


b.

Interchange the headlight unit assembly LH with RH and connect the connectors.


c.

Operate the turn signal switch and check that the RH side turn signal light operates normally.

NOTICE:

If the RH side front turn signal light operates normally, return the headlight unit assembly LH and headlight unit assembly RH that were interchanged in a previous step back to their original conditions so that a component of the headlight unit assembly RH can be inspected in the next step.



Result:
Result Proceed to
RH side front turn signal light operates normally A
Problem symptoms do not change
(RH side front turn signal light does not blink)
B



A

REPLACE HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE HEADLIGHT LENS SUB-ASSEMBLY RH

24.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the B89 headlight ECU sub-assembly RH connector.


b.

Disconnect the I6 combination meter assembly connector.



Result:
Proceed to
OK
NG



OK

25.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

27.CHECK HEADLIGHT CORD RH
25.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.
B612074C10
1.479,2.75 2,3.01 0.521,0.26 1.479,0.24 2,0.5 0.521,0.26 2.51,3.542 2.75,2.917 2.75,2.917 2.917,2.917 true 1.688,0.313 1.844,0.51 0.156,0.198 10 false B 1.656,2.802 2.031,3.052 0.375,0.25 10 false I6 0.323,0.563 0.646,0.76 0.323,0.198 10 false *a 0.354,2.781 0.698,2.938 0.344,0.156 10 false *b 2.969,2.854 3.281,3.052 0.313,0.198 10 false LR
*a Component with harness connected
(Headlight ECU Sub-assembly RH)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Remove the headlight ECU sub-assembly RH as a unit with the connectors still connected.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Disconnect the I6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-5 (LR) - B-6 Always Below 1 Ω
B-20 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

26.CHECK HEADLIGHT UNIT ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

26.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Remove the headlight unit assembly LH and RH.


b.

Interchange the headlight unit assembly LH with RH and connect the connectors.


c.

Operate the turn signal switch and check that the RH side turn signal light operates normally.

NOTICE:

If the RH side front turn signal light operates normally, return the headlight unit assembly LH and headlight unit assembly RH that were interchanged in a previous step back to their original conditions so that a component of the headlight unit assembly RH can be inspected in the next step.



Result:
Result Proceed to
RH side front turn signal light operates normally A
Problem symptoms do not change
(RH side front turn signal light does not blink)
B



A

REPLACE HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE HEADLIGHT LENS SUB-ASSEMBLY RH

27.CHECK HEADLIGHT CORD RH
a.

Disconnect the BB8, BB9 and B89 headlight cord RH connectors.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



b.

Measure the resistance according to the value(s) in the table below.

E507307C02
1.375,0.135 1.792,0.406 0.417,0.271 3.854,0.094 4.271,0.365 0.417,0.271 5.792,0.156 6.208,0.427 0.417,0.271 4.521,0.99 4.729,1.313 4.729,1.313 4.885,1.313 true 6.156,1.042 6.365,1.365 6.365,1.365 6.521,1.365 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.469,0.198 1.927,0.396 0.458,0.198 10 false B89 3.938,0.146 4.396,0.344 0.458,0.198 10 false BB8 5.865,0.208 6.323,0.406 0.458,0.198 10 false BB9 4.979,1.229 5.438,1.427 0.458,0.198 10 false TNS 6.604,1.271 7.063,1.469 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Headlight Cord RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB8,B89,BB9)Location & Routing

Click Connector(BB8)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Lamp Wire

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

Click Connector(BB9)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Lamp Wire

BB8-7 - B89-11 (TNS) Always Below 1 Ω
BB9-1 - B89-12 (GND) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

28.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT HOUSING RH AND BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B6 headlight housing RH connector.



Result:
Proceed to
OK
NG



OK

29.INSPECT HEADLIGHT HOUSING RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.INSPECT HEADLIGHT HOUSING RH
a.
B611438C01
1.552,1.604 1.969,1.875 0.417,0.271 1.531,0.198 1.969,0.479 0.438,0.281 0.625,0.354 0.938,0.552 0.313,0.198 10 false *a 1.708,0.25 2.021,0.448 0.313,0.198 10 false A 1.708,1.656 2.021,1.854 0.313,0.198 10 false B 0.573,1.677 0.885,1.875 0.313,0.198 10 false *b
*a Component without harness connected
(to Headlight Housing RH)
*b Component without harness connected
(to Headlight Lens Sub-assembly RH)


Remove the headlight housing RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-8 - B-1 Always Below 1 Ω
A-7 - B-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LENS SUB-ASSEMBLY RH

NG

30.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Outer Mirror Control ECU Assembly A
w/o Outer Mirror Control ECU Assembly B



A

31.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

34.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
31.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N1 outer mirror control ECU assembly LH connector.


b.

Disconnect the I6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,N1)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(N1)Body>Front Door Wire LH>Outer Mirror Control ECU Assembly LH

I6-14 (LL) - N1-11 (TRNI) Always Below 1 Ω
N1-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

32.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

33.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
33.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH

OK

REPLACE OUTER MIRROR RETRACTOR LH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

34.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

35.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
35.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH

OK

REPLACE OUTER MIRROR RETRACTOR LH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

36.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Outer Mirror Control ECU Assembly A
w/o Outer Mirror Control ECU Assembly B



A

37.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

40.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
37.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the M1 outer mirror control ECU assembly RH connector.


b.

Disconnect the I6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,M1)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(M1)Body>Front Door Wire RH>Outer Mirror Control ECU Assembly RH

I6-5 (LR) - M1-11 (TRNI) Always Below 1 Ω
M1-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

38.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

39.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
39.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH

OK

REPLACE OUTER MIRROR RETRACTOR RH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

40.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

41.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
41.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH

OK

REPLACE OUTER MIRROR RETRACTOR RH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

42.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Sequential Type Turn Signal Light A
except Sequential Type Turn Signal Light (w/ Turn Light LED Type) B
except Sequential Type Turn Signal Light (w/ Turn Light Bulb Type) C



A

43.INSPECT LIGHTS

B

57.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD LH - COMBINATION METER ASSEMBLY)

C

60.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD LH - COMBINATION METER ASSEMBLY)
43.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
All LH side rear turn signal lights do not blink. A
Rear light assembly LH does not illuminate. B
Rear combination light assembly LH does not illuminate. C



A

44.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

51.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

54.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
44.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the c2 rear combination light cord LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,c2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(c2)Body>No. 8 Floor Wire>Rear Combination Light Assembly LH

I6-1 (TRNL) - c2-1 (TRN) Always Below 1 Ω
c2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

45.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the g2 rear light socket and wire LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,g2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(g2)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly LH

I6-1 (TRNL) - g2-3 (B) Always Below 1 Ω
g2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

46.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE LH - REAR COMBINATION LIGHT CORD LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

46.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE LH - REAR COMBINATION LIGHT CORD LH)
a.

Disconnect the g2 rear light socket and wire LH connector.


b.

Disconnect the c2 rear combination light cord LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g2,c2)Location & Routing

Click Connector(g2)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(c2)Body>No. 8 Floor Wire>Rear Combination Light Assembly LH

g2-2 (TRN4) - c2-3 (TRN1) Always Below 1 Ω
g2-1(TRN3) - c2-2 (TRN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

47.INSPECT REAR LIGHT SOCKET AND WIRE LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

47.INSPECT REAR LIGHT SOCKET AND WIRE LH

OK

48.INSPECT REAR COMBINATION LIGHT CORD LH

NG

REPLACE REAR LIGHT SOCKET AND WIRE LH

48.INSPECT REAR COMBINATION LIGHT CORD LH

OK

49.CHECK COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT CORD LH

49.CHECK COMBINATION METER ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-1 (TRNL) - Body ground Ignition switch ON, LH turn indicator light blinking 11 to 14 V ←→ Below 1 V



Result:
Proceed to
OK
NG



OK

50.CHECK REAR LIGHT ASSEMBLY LH

NG

REPLACE COMBINATION METER ASSEMBLY

50.CHECK REAR LIGHT ASSEMBLY LH
a.

Remove the rear light assembly LH and RH.


b.

Interchange the rear light assembly LH with RH and connect the connectors.


c.

Operate the turn signal switch and check that the LH side front turn signal light operates normally.

NOTICE:

If the LH side rear turn signal light operates normally, return the rear light assembly LH and rear light assembly RH that were interchanged in a previous step back to their original conditions so that a component of the rear light assembly LH can be inspected in the next step.



Result:
Proceed to
OK
NG



OK

REPLACE REAR LIGHT ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

51.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the g2 rear light socket and wire LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,g2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(g2)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly LH

I6-1 (TRNL) - g2-3 (B) Always Below 1 Ω
g2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

52.INSPECT REAR LIGHT SOCKET AND WIRE LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

52.INSPECT REAR LIGHT SOCKET AND WIRE LH

OK

53.CHECK COMBINATION METER ASSEMBLY

NG

REPLACE REAR LIGHT SOCKET AND WIRE LH

53.CHECK COMBINATION METER ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-1 (TRNL) - Body ground Ignition switch ON, LH turn indicator light blinking 11 to 14 V ←→ Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR LIGHT ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

54.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the c2 rear combination light cord LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Rear combination light assembly LH
Tester Connection Condition Specified Condition

Click Location & Routing(I6,c2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(c2)Body>No. 8 Floor Wire>Rear Combination Light Assembly LH

I6-1 (TRNL) - c2-1 (TRN) Always Below 1 Ω
c2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

55.INSPECT REAR COMBINATION LIGHT CORD LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.INSPECT REAR COMBINATION LIGHT CORD LH

OK

56.CHECK COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT CORD LH

56.CHECK COMBINATION METER ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-1 (TRNL) - Body ground Ignition switch ON, LH turn indicator light blinking 11 to 14 V ←→ Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

NG

REPLACE COMBINATION METER ASSEMBLY

57.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD LH - COMBINATION METER ASSEMBLY)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the c2 rear combination light cord LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,c2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(c2)Body>No. 8 Floor Wire>Rear Combination Light Assembly LH

I6-1 (TRNL) - c2-1 (TRN) Always Below 1 Ω
c2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

58.INSPECT REAR COMBINATION LIGHT CORD LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

58.INSPECT REAR COMBINATION LIGHT CORD LH

OK

59.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

NG

REPLACE REAR COMBINATION LIGHT CORD LH

59.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

60.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD LH - COMBINATION METER ASSEMBLY)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the c2 rear combination light cord LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,c2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(c2)Body>No. 8 Floor Wire>Rear Combination Light Assembly LH

I6-1 (TRNL) - c2-1 (TRN) Always Below 1 Ω
c2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

61.INSPECT REAR COMBINATION LIGHT CORD LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

61.INSPECT REAR COMBINATION LIGHT CORD LH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT CORD LH

62.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Sequential Type Turn Signal Light A
except Sequential Type Turn Signal Light (w/ Turn Light LED Type) B
except Sequential Type Turn Signal Light (w/ Turn Light Bulb Type) C



A

63.INSPECT LIGHTS

B

75.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

78.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
63.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
All RH side rear turn signal lights do not blink. A
Rear light assembly RH does not illuminate. B
Rear combination light assembly RH does not illuminate. C



A

64.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY)

B

71.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE RH AND REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

73.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE RH AND REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY)
64.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the g1 rear combination light cord RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,g1)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(g1)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly RH

I6-2 (TRNR) - g1-3 (B) Always Below 1 Ω
g1-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

65.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE RH - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

65.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE RH - COMBINATION METER ASSEMBLY)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the b2 rear light socket and wire RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,b2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(b2)Body>No. 7 Floor Wire>Rear Combination Light Assembly RH

I6-2 (TRNR) - b2-1 (TRN) Always Below 1 Ω
b2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

66.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE RH - REAR COMBINATION LIGHT CORD RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

66.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE RH - REAR COMBINATION LIGHT CORD RH)
a.

Disconnect the g1 rear light socket and wire RH connector.


b.

Disconnect the b2 rear combination light cord RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b2,g1)Location & Routing

Click Connector(b2)Body>No. 7 Floor Wire>Rear Combination Light Assembly RH

Click Connector(g1)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly RH

b2-2 (TRN2) - g1-1 (TRN3) Always Below 1 Ω
b2-3 (TRN1) - g1-2 (TRN4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

67.INSPECT REAR LIGHT SOCKET AND WIRE RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

67.INSPECT REAR LIGHT SOCKET AND WIRE RH

OK

68.INSPECT REAR COMBINATION LIGHT CORD RH

NG

REPLACE REAR LIGHT SOCKET AND WIRE LH

68.INSPECT REAR COMBINATION LIGHT CORD RH

OK

69.CHECK COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT CORD RH

69.CHECK COMBINATION METER ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-2 (TRNR) - Body ground Ignition switch ON, RH turn indicator light blinking 11 to 14 V ←→ Below 1 V



Result:
Proceed to
OK
NG



OK

70.CHECK REAR LIGHT ASSEMBLY RH

NG

REPLACE COMBINATION METER ASSEMBLY

70.CHECK REAR LIGHT ASSEMBLY RH
a.

Remove the rear light assembly LH and RH.


b.

Interchange the rear light assembly RH with LH and connect the connectors.


c.

Operate the turn signal switch and check that the RH side front turn signal light operates normally.

NOTICE:

If the RH side rear turn signal light operates normally, return the rear light assembly LH and rear light assembly RH that were interchanged in a previous step back to their original conditions so that a component of the rear light assembly LH can be inspected in the next step.



Result:
Proceed to
OK
NG



OK

REPLACE REAR LIGHT ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

71.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE RH AND REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the b2 rear light socket and wire RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,b2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(b2)Body>No. 7 Floor Wire>Rear Combination Light Assembly RH

I6-2 (TRNR) - b2-1 (TRN) Always Below 1 Ω
b2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

72.INSPECT REAR LIGHT SOCKET AND WIRE RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

72.INSPECT REAR LIGHT SOCKET AND WIRE RH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR LIGHT SOCKET AND WIRE RH

73.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE RH AND REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the b2 rear combination light cord RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,b2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(b2)Body>No. 7 Floor Wire>Rear Combination Light Assembly RH

I6-2 (TRNR) - b2-1 (TRN) Always Below 1 Ω
b2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

74.INSPECT REAR COMBINATION LIGHT CORD RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

74.INSPECT REAR COMBINATION LIGHT CORD RH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT CORD RH

75.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the b2 rear combination light cord RH connector.



Result:
Proceed to
OK
NG



OK

76.INSPECT REAR COMBINATION LIGHT CORD RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

76.INSPECT REAR COMBINATION LIGHT CORD RH

OK

77.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

NG

REPLACE REAR COMBINATION LIGHT CORD RH

77.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

78.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the b2 rear combination light cord RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,b2)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(b2)Body>No. 7 Floor Wire>Rear Combination Light Assembly RH

I6-2 (TRNR) - b2-1 (TRN) Always Below 1 Ω
b2-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

79.INSPECT REAR COMBINATION LIGHT CORD RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

79.INSPECT REAR COMBINATION LIGHT CORD RH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT CORD RH