| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| U0122 | CAN Communication Error (VSC) | The DTC output ECU does not receive data from the brake actuator assembly (No. 2 skid control ECU). |
·
CAN main/branch bus lines or connector
·
ECM
·
Engine stop and start ECU (w/ Stop and Start System)
·
Absorber control ECU (w/ Adaptive Variable Suspension System)
·
Brake booster with master cylinder assembly (No. 1 skid control ECU)
·
Brake actuator assembly (No. 2 skid control ECU)
·
No. 1 Global CAN Junction Connector (for LHD)
·
No. 7 Global CAN Junction Connector
·
No. 2 CAN junction connector (for RHD) |
Adaptive Variable Suspension System | A |
| U012987 | Lost Communication With Brake System Control Module Missing Message | The DTC output ECU does not receive data from the brake actuator assembly (No. 2 skid control ECU). |
·
CAN main/branch bus lines or connector
·
ECM
·
Engine stop and start ECU (w/ Stop and Start System)
·
Absorber control ECU (w/ Adaptive Variable Suspension System)
·
Brake booster with master cylinder assembly (No. 1 skid control ECU)
·
Brake actuator assembly (No. 2 skid control ECU)
·
No. 1 Global CAN Junction Connector (for LHD)
·
No. 7 Global CAN Junction Connector
·
No. 2 CAN junction connector (for RHD) |
Engine | A |
| U115987 | Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message | The DTC output ECU does not receive data from the brake booster with master cylinder assembly (No. 1 skid control ECU). |
·
CAN main/branch bus lines or connector
·
ECM
·
Engine stop and start ECU (w/ Stop and Start System)
·
Absorber control ECU (w/ Adaptive Variable Suspension System)
·
Brake booster with master cylinder assembly (No. 1 skid control ECU)
·
Brake actuator assembly (No. 2 skid control ECU)
·
No. 1 Global CAN Junction Connector (for LHD)
·
No. 7 Global CAN Junction Connector
·
No. 2 CAN junction connector (for RHD) |
Brake/EPB | A |
| U115C00 | Lost Communication with ECM/PCM "A" (ch5) | The DTC output ECU does not receive data from the ECM. |
·
CAN main/branch bus lines or connector
·
ECM
·
Engine stop and start ECU (w/ Stop and Start System)
·
Absorber control ECU (w/ Adaptive Variable Suspension Sysem)
·
Brake booster with master cylinder assembly (No. 1 skid control ECU)
·
Brake actuator assembly (No. 2 skid control ECU)
·
No. 1 Global CAN Junction Connector (for LHD)
·
No. 7 Global CAN Junction Connector
·
No. 2 CAN junction connector (for RHD) |
Brake Booster | A |
| U115C87 | Lost Communication with ECM/PCM "A" (ch5) Missing Message | The DTC output ECU does not receive data from the ECM. |
·
CAN main/branch bus lines or connector
·
ECM
·
Engine stop and start ECU (w/ Stop and Start System)
·
Absorber control ECU (w/ Adaptive Variable Suspension Sysem)
·
Brake booster with master cylinder assembly (No. 1 skid control ECU)
·
Brake actuator assembly (No. 2 skid control ECU)
·
No. 1 Global CAN Junction Connector (for LHD)
·
No. 7 Global CAN Junction Connector
·
No. 2 CAN junction connector (for RHD) |
Brake/EPB | A |
| U117087 | Lost Communication With Brake System Control Module(ch2) Missing Message | The DTC output ECU does not receive data from the brake actuator assembly (No. 2 skid control ECU). |
·
CAN main/branch bus lines or connector
·
ECM
·
Engine stop and start ECU (w/ Stop and Start System)
·
Absorber control ECU (w/ Adaptive Variable Suspension Sysem)
·
Brake booster with master cylinder assembly (No. 1 skid control ECU)
·
Brake actuator assembly (No. 2 skid control ECU)
·
No. 1 Global CAN Junction Connector (for LHD)
·
No. 7 Global CAN Junction Connector |
Stop and Start | A |
| U117D87 | Lost Communication with Brake System Control Module (ch4) Missing Message | The DTC output ECU does not receive data from the brake actuator assembly (No. 2 skid control ECU). |
·
CAN main/branch bus lines or connector
·
ECM
·
Engine stop and start ECU (w/ Stop and Start System)
·
Absorber control ECU (w/ Adaptive Variable Suspension Sysem)
·
Brake booster with master cylinder assembly (No. 1 skid control ECU)
·
Brake actuator assembly (No. 2 skid control ECU)
·
No. 1 Global CAN Junction Connector (for LHD)
·
No. 7 Global CAN Junction Connector
·
No. 2 CAN junction connector (for RHD) |
Brake Booster | A |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check for DTCs.
| Display on GTS / Output DTC | Pattern | |||||
|---|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||||
| Engine | U012987 | - | ○ | ○ | - | - |
| Adaptive Variable Suspension System | U0122 | - | - | - | ○ | - |
| Stop and Start | U117087 | - | - | - | - | ○ |
| Brake Booster | U115C00 | ○ | - | ○ | - | - |
| U117D87 | - | - | - | - | - | |
| Brake/EPB | U115C87 | ○ | - | ○ | - | - |
| U115987 | - | - | - | - | - | |
| Display on GTS / Output DTC | Pattern | |||||
|---|---|---|---|---|---|---|
| Pattern 4 | Pattern 5 | |||||
| Engine | U012987 | - | - | ○ | - | ○ |
| Adaptive Variable Suspension System | U0122 | - | - | ○ | - | ○ |
| Stop and Start | U117087 | - | - | ○ | - | ○ |
| Brake Booster | U115C00 | ○ | ○ | - | - | - |
| U117D87 | ○ | ○ | ○ | - | ○ | |
| Brake/EPB | U115C87 | - | - | ○ | ○ | - |
| U115987 | ○ | - | ○ | ○ | - | |
| Result | Proceed to |
|---|---|
| Pattern 1 | A |
| Pattern 2 | B |
| Pattern 3 | C |
| Pattern 4 | D |
| Pattern 5 | E |
| Other Pattern | F |
A
B
C
D
E
F
Pre-procedure1
Disconnect the cable from the negative (-) battery terminal.
Disconnect the B2*1, B1*2 or B70*3 ECM connector.
*1: for 1GR-FE
*2: for V35A-FTS
*3: for F33A-FTV
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B2)Location & Routingewd_type=routing;type=c;code=B2 |
||
| B2-10 (CANP) - B2-18 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B1)Location & Routingewd_type=routing;type=c;code=B1 |
||
| B1-16 (CACH) - B1-15 (CACL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B70)Location & Routingewd_type=routing;type=c;code=B70 |
||
| B70-17 (CACH) - B70-18 (CACL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Result | Proceed to |
|---|---|
| OK (for 1GR-FE) | A |
| OK (for V35A-FTS) | B |
| OK (for F33A-FTV) | C |
| NG | D |
Post-procedure1
None
A
B
C
D
Pre-procedure1
Disconnect the cable from the negative (-) battery terminal.
Disconnect the Q11 absorber control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Q11)Location & Routingewd_type=routing;type=c;code=Q11 |
||
| Q11-19 (CA2H) - Q11-18 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) battery terminal.
Disconnect the I57 engine stop and start ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57)Location & Routingewd_type=routing;type=c;code=I57 |
||
| I57-15 (LC1H) - I57-16 (LC1L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) battery terminal.
Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B19)Location & Routingewd_type=routing;type=c;code=B19 |
||
| B19-35 (CA2H) - B19-36 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL
NG
Pre-procedure1
Disconnect the cable from the negative (-) battery terminal.
Disconnect the B20 brake actuator assembly (No. 2 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B20)Location & Routingewd_type=routing;type=c;code=B20 |
||
| B20-16 (CA2H) - B20-17 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 109 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-12 (CAWH) - I42-13 (CAWL) | Cable disconnected from negative (-) battery terminal | Below 70 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-12 (CAWH) - I42-13 (CAWL) | Cable disconnected from negative (-) battery terminal | 54 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42,I76)Location & Routingewd_type=routing;type=c,c;code=I42,I76 |
||
| I42-12 (CAWH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-13 (CAWL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42,I76)Location & Routingewd_type=routing;type=c,c;code=I42,I76 |
||
| I42-12 (CAWH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-13 (CAWL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the I178 No. 7 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-9 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-20 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Adaptive Variable Suspension System | A |
| w/o Adaptive Variable Suspension System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-10 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-21 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Stop and Start System | A |
| w/o Stop and Start System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-11 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-22 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B66 No. 1 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=2,13 |
||
| B66-2 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B66-13 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=1,12 |
||
| B66-1 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B66-12 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=3,14 |
||
| B66-3 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B66-14 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=4,15 |
||
| B66-4 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B66-15 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=1,12 |
||
| B66-1 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B66-12 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=3,14 |
||
| B66-3 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B66-14 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B1*1, B2*2 or B70*3 ECM connector.
*1: for V35A-FTS
*2: for 1GR-FE
*3: for F33A-FTV
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=4,15 |
||
| B66-4 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B66-15 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTV: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
Pre-procedure1
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the Q11 absorber control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-10 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-21 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I57 engine stop and start ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-11 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-22 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I178 No. 7 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-9 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-20 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Adaptive Variable Suspension System | A |
| w/o Adaptive Variable Suspension System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-10 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-21 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Stop and Start System | A |
| w/o Stop and Start System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-11 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-22 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B66 No. 1 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=2,13 |
||
| B66-2 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B66-13 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=1,12 |
||
| B66-1 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B66-12 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=3,14 |
||
| B66-3 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B66-14 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=4,15 |
||
| B66-4 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B66-15 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=1,12 |
||
| B66-1 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B66-12 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=3,14 |
||
| B66-3 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B66-14 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B1*1, B2*2 or B70*3 ECM connector.
*1: for V35A-FTS
*2: for 1GR-FE
*3: for F33A-FTV
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66,I76)Location & Routingewd_type=routing;type=c,c;code=B66,I76 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=4,15 |
||
| B66-4 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B66-15 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTV: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
Pre-procedure1
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the Q11 absorber control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-10 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-21 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I57 engine stop and start ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-11 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-22 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I178 No. 7 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-9 (CANH) - I178-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-8 (CANH) - I178-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Adaptive Variable Suspension System | A |
| w/o Adaptive Variable Suspension System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-10 (CANH) - I178-21 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Stop and Start System | A |
| w/o Stop and Start System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-11 (CANH) - I178-22 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B66 No. 1 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66)Location & Routingewd_type=routing;type=c;code=B66 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=2,13 |
||
| B66-2 (CANH) - B66-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66)Location & Routingewd_type=routing;type=c;code=B66 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=1,12 |
||
| B66-1 (CANH) - B66-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66)Location & Routingewd_type=routing;type=c;code=B66 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=3,14 |
||
| B66-3 (CANH) - B66-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66)Location & Routingewd_type=routing;type=c;code=B66 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=4,15 |
||
| B66-4 (CANH) - B66-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66)Location & Routingewd_type=routing;type=c;code=B66 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=1,12 |
||
| B66-1 (CANH) - B66-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66)Location & Routingewd_type=routing;type=c;code=B66 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=3,14 |
||
| B66-3 (CANH) - B66-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B1*1, B2*2 or B70*3 ECM connector.
*1: for V35A-FTS
*2: for 1GR-FE
*3: for F33A-FTV
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66)Location & Routingewd_type=routing;type=c;code=B66 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=4,15 |
||
| B66-4 (CANH) - B66-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTV: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
Pre-procedure1
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-8 (CANH) - I178-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the Q11 absorber control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-10 (CANH) - I178-21 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I57 engine stop and start ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-11 (CANH) - I178-22 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I178 No. 7 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-9 (CANH) - I178-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-8 (CANH) - I178-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Reconnect the I178 No. 7 global CAN junction connector.
Disconnect the B66 No. 1 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66)Location & Routingewd_type=routing;type=c;code=B66 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=2,13 |
||
| B66-2 (CANH) - B66-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B66)Location & Routingewd_type=routing;type=c;code=B66 Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connectorewd_type=component;type=c;code=B66;pinno=1,12 |
||
| B66-1 (CANH) - B66-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I178 No. 7 global CAN junction connector.
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-12 (CAWH) - I42-13 (CAWL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Reconnect the B66 No. 1 global CAN junction connector.
Procedure1
Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B20)Location & Routingewd_type=routing;type=c;code=B20 |
||
| B20-16 (CA2H) - B20-17 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-12 (CAWH) - I42-13 (CAWL) | Cable disconnected from negative (-) battery terminal | Below 70 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-12 (CAWH) - I42-13 (CAWL) | Cable disconnected from negative (-) battery terminal | 54 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42,I76)Location & Routingewd_type=routing;type=c,c;code=I42,I76 |
||
| I42-12 (CAWH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-13 (CAWL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42,I76)Location & Routingewd_type=routing;type=c,c;code=I42,I76 |
||
| I42-12 (CAWH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-13 (CAWL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the I178 No. 7 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-9 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-20 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Adaptive Variable Suspension System | A |
| w/o Adaptive Variable Suspension System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-10 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-21 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B48 No. 2 CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=2,13 |
||
| B48-2 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B48-13 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=1,12 |
||
| B48-1 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B48-12 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=3,14 |
||
| B48-3 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B48-14 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=4,15 |
||
| B48-4 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B48-15 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=1,12 |
||
| B48-1 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B48-12 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=3,14 |
||
| B48-3 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B48-14 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B1*1 or B70*2 ECM connector.
*1: for V35A-FTS
*2: for F33A-FTV
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=4,15 |
||
| B48-4 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B48-15 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
Pre-procedure1
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the Q11 absorber control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-10 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I178-21 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I178 No. 7 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-9 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-20 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Adaptive Variable Suspension System | A |
| w/o Adaptive Variable Suspension System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-10 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-21 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B48 No. 2 CAN junction connector.
Pre-procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=2,13 |
||
| B48-2 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B48-13 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=1,12 |
||
| B48-1 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B48-12 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=3,14 |
||
| B48-3 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B48-14 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=4,15 |
||
| B48-4 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B48-15 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=1,12 |
||
| B48-1 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B48-12 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=3,14 |
||
| B48-3 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B48-14 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B1 or B70*2 ECM connector.
*1: for V35A-FTS
*2: for F33A-FTV
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48,I76)Location & Routingewd_type=routing;type=c,c;code=B48,I76 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=4,15 |
||
| B48-4 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B48-15 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
Pre-procedure1
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the Q11 absorber control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178,I76)Location & Routingewd_type=routing;type=c,c;code=I178,I76 |
||
| I178-10 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I178-21 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I178 No. 7 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-9 (CANH) - I178-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-8 (CANH) - I178-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Adaptive Variable Suspension System | A |
| w/o Adaptive Variable Suspension System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-10 (CANH) - I178-21 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B48 No. 2 CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48)Location & Routingewd_type=routing;type=c;code=B48 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=2,13 |
||
| B48-2 (CANH) - B48-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48)Location & Routingewd_type=routing;type=c;code=B48 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=1,12 |
||
| B48-1 (CANH) - B48-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48)Location & Routingewd_type=routing;type=c;code=B48 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=3,14 |
||
| B48-3 (CANH) - B48-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48)Location & Routingewd_type=routing;type=c;code=B48 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=4,15 |
||
| B48-4 (CANH) - B48-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48)Location & Routingewd_type=routing;type=c;code=B48 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=1,12 |
||
| B48-1 (CANH) - B48-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48)Location & Routingewd_type=routing;type=c;code=B48 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=3,14 |
||
| B48-3 (CANH) - B48-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B1*1 or B70*2 ECM connector.
*1: for V35A-FTS
*2: for F33A-FTV
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48)Location & Routingewd_type=routing;type=c;code=B48 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=4,15 |
||
| B48-4 (CANH) - B48-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
Pre-procedure1
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-8 (CANH) - I178-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the Q11 absorber control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-10 (CANH) - I178-21 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I178 No. 7 global CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-9 (CANH) - I178-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I178)Location & Routingewd_type=routing;type=c;code=I178 |
||
| I178-8 (CANH) - I178-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Reconnect the I178 No. 7 global CAN junction connector.
Disconnect the B48 No. 2 CAN junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48)Location & Routingewd_type=routing;type=c;code=B48 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=2,13 |
||
| B48-2 (CANH) - B48-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B48)Location & Routingewd_type=routing;type=c;code=B48 Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connectorewd_type=component;type=c;code=B48;pinno=1,12 |
||
| B48-1 (CANH) - B48-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I178 No. 7 global CAN junction connector.
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-12 (CAWH) - I42-13 (CAWL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Reconnect the B48 No. 2 CAN junction connector.
Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B20)Location & Routingewd_type=routing;type=c;code=B20 |
||
| B20-16 (CA2H) - B20-17 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG