Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › ENGINE UNIT
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133486 ENGINE UNIT A

1HZ ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE ENGINE HANGER

a.
A326287C01
0.052,0.063 0.323,0.281 0.271,0.219 10 false *A 1.906,0.052 2.219,0.208 0.313,0.156 10 false *B
*A for Front Side
*B for Rear Side


Remove the 4 bolts and 2 engine hangers.


Hide 23760 2.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23600 3.REMOVE NOZZLE HOLDER AND NOZZLE SET

Hide 15721 4.REMOVE OIL COOLER COVER

Hide 15710 5.REMOVE OIL COOLER ASSEMBLY

Hide 12108 6.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 11201 7.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 13523P 8.REMOVE CAMSHAFT TIMING PULLEY

Hide 11385 9.REMOVE CAMSHAFT OIL SEAL RETAINER

Hide 11183 12.REMOVE SEMICIRCULAR PLUG

a.

Remove the semicircular plug.


Hide 13.REMOVE VALVE LIFTER AND ADJUSTING VALVE SHIM

a.

Remove the 12 valve lifters and 12 adjusting valve shims.

HINT:

Arrange the valve lifters and adjusting valve shims in correct order.



Hide 16100 14.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 11101 15.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11322F 19.REMOVE NO. 2 TIMING GEAR COVER

a.
A327199

Remove the 15 bolts.


b.
A327200C01
1.167,0.833 1.354,0.833 1.354,0.833 1.521,0.719 true 0.99,0.74 1.198,0.927 0.208,0.188 10 false *a
*a Protective Tape


Using a screwdriver, remove the No. 2 timing gear cover by prying between the No. 2 timing gear cover and timing gear case sub-assembly.

HINT:

Tape the screwdriver tip before use.



Hide 20.CHECK THRUST CLEARANCE NO. 1 IDLE GEAR

a.
A327201

Using a thickness gauge, measure the thrust clearance.

Standard thrust clearance:

0.05 to 0.15 mm (0.00197 to 0.00591 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the thrust plate. If necessary, replace the No. 1 idle gear and/or No. 1 idle gear shaft.


Hide 13522C 21.REMOVE DRIVE SHAFT PUMP GEAR

a.
A329188N01
1.573,1.323 2.104,1.615 2.104,1.615 2.24,1.615 false 3.104,1.615 3.104,1.406 3.104,1.406 2.979,1.208 false 2.292,1.531 2.615,1.708 0.323,0.177 10 false SST 2.969,1.646 3.323,1.854 0.354,0.208 10 false SST

Using SST, remove the drive shaft pump gear.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04051)
09950-60010  (09951-00400)


Hide 13525 22.REMOVE NO. 1 IDLE GEAR

a.
A329189

Remove the 2 bolts, idle gear thrust plate, No. 1 idler gear and No. 1 idler gear shaft.


Hide 13613 23.REMOVE INJECTION PUMP DRIVE GEAR

a.
A329208

Remove the O-ring.


b.
A329191N01
1.417,1.292 2.042,1.781 2.042,1.781 2.24,1.781 true 2.896,1.385 2.896,0.938 false 2.781,1.406 3.135,1.594 0.354,0.188 10 false SST 2.292,1.698 2.646,1.885 0.354,0.188 10 false SST

Using SST, remove the injection pump drive gear.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031, 09957-04010)

NOTICE:
·

Tighten the 2 bolts of SST more 8 mm (0.315 in.).

·

Set SST so that it is balanced.



HINT:

Temporarily install the injection pump in order to remove the injection pump drive gear.



Hide 13521 24.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A329192N01
2.385,1.719 2.188,1.719 2.188,1.719 1.667,1.146 false 3.115,1.49 3.115,1.198 3.115,1.198 3,0.958 false 2.438,1.646 2.76,1.833 0.323,0.188 10 false SST 2.99,1.521 3.313,1.708 0.323,0.188 10 false SST

Using SST, remove the crankshaft timing gear or sprocket.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051)


Hide 12101A 25.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket.


Hide 12101 26.REMOVE OIL PAN SUB-ASSEMBLY

Hide 15104 27.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 11301 28.REMOVE TIMING GEAR CASE SUB-ASSEMBLY

Hide 11381 29.REMOVE REAR ENGINE OIL SEAL RETAINER

a.
A321601C01
0.292,0.323 0.427,0.323 0.427,0.323 0.875,0.771 true 0.115,0.229 0.427,0.385 0.313,0.156 10 false *a
*a Protective Tape


Remove the 6 bolts and rear engine oil seal retainer.

HINT:

Tape the screwdriver tip before use.



Hide 11381A 30.REMOVE REAR CRANKSHAFT OIL SEAL