Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0234  Turbocharger / Supercharger Overboost Condition  P1251  Turbocharger / Supercharger Overboost Condition (Too High)  


DESCRIPTION

The variable nozzle vane type turbocharger operates the vacuum type actuator and controls the nozzle vane by using the VRV, which is controlled by the ECM. At a low to medium vehicle speed, when the nozzle vane moves in the closing direction and the exhaust gas rate of flow becomes faster, the engine torque increases. At a high vehicle speed, when the nozzle vane moves in the opening direction, the exhaust pressure decreases. This leads to improved fuel consumption and engine output.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0234 Turbocharger / Supercharger Overboost Condition When turbocharger boost pressure continues to be higher than ECM's target boost pressure.
(1 trip detection logic)
·

Turbocharger sub-assembly

·

Extremely low battery voltage (P0560 output simultaneously)

·

VN turbo link stuck malfunction

·

Intake system

·

Exhaust system

·

Electric EGR control valve assembly

·

EGR cooler

·

EGR system line deposits or clogs

·

Fuel injector

·

Diesel throttle body assembly

·

ECM

·

DPF catalytic converter or DOC catalytic converter cracks or removal


Comes on DTC stored
P1251 Turbocharger / Supercharger Overboost Condition (Too High) When turbocharger boost pressure is higher than boost pressure for a short time in which there was possibility of engine damage.
(1 trip detection logic)
·

Turbocharger sub-assembly

·

Extremely low battery voltage (P0560 output simultaneously)

·

VN turbo link stuck malfunction

·

Intake system

·

Exhaust system

·

Electric EGR control valve assembly

·

EGR cooler

·

EGR system line deposits or clogs

·

Fuel injector

·

Diesel throttle body assembly

·

ECM

·

DPF catalytic converter or DOC catalytic converter cracks or removal


Comes on DTC stored

HINT:

If DTC P0234 or P1251 is stored, the following symptoms may appear.

When the nozzle vane of the turbocharger is stuck closed:

-

Vehicle surge when driving with full load

-

Low power output due to ECM limiting power output




Related Data List
DTC No. Data List
P0234
·

MAP

·

Target Booster Pressure

·

MAF

·

Target EGR Position

·

Actual EGR Valve Pos.

·

VN Turbo Command

·

Atmosphere Pressure


P1251

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0234 After warming up the engine, the vehicle is driven at a constant vehicle speed at an engine speed of 2400 rpm or more for 2 minutes
P1251 After warming up the engine, fully depress the accelerator pedal for 5 seconds or more so that the engine speed is 2400 rpm or more.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Record the stored DTC and freeze frame data.

HINT:

Be sure to carefully examine "MAP" and "Target Booster Pressure" in the freeze frame data.



Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0234 AND/OR P1251)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0234 AND/OR P1251)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
DTC P0234 and/or P1251 are output A
DTC P0234 and/or P1251 and other DTCs are output B


HINT:

If DTCs other than P0234 and/or P1251 are output, perform troubleshooting for those DTCs first.




A

3.READ VALUE USING GTS (MAP AND TARGET BOOSTER PRESSURE)

B

3.READ VALUE USING GTS (MAP AND TARGET BOOSTER PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Target Booster Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
Target Booster Pressure
50003 234 4,834

d.

Take a snapshot when the engine speed is maintained at 4500 rpm with no load.


e.

Read the values of "MAP" and "Target Booster Pressure" in the Data List using the snapshot review function.

Result:
Result Proceed to
Difference between MAP and Target Booster Pressure is +/-15 kPa or higher A
Except above B




A

4.CHECK AIR INTAKE SYSTEM

B

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK AIR INTAKE SYSTEM
a.

Check for air leaks and blockages between the air cleaner case and turbocharger sub-assembly, and between turbocharger sub-assembly and intake manifold.

Result:
Result Proceed to
Leaks and/or blockages exist in the intake system A
No leaks and/or blockages in the intake system B


HINT:
·

Inspect the air intake system, especially hoses and pipes between the air cleaner assembly and turbocharger sub-assembly.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

·

Check for any modifications in the intake system made by the user.

·

Check if the vacuum hose for the manifold absolute pressure sensor is disconnected.





A

5.REPAIR OR REPLACE AIR INTAKE SYSTEM

B

7.CHECK CONNECTION OF VACUUM HOSE
5.REPAIR OR REPLACE AIR INTAKE SYSTEM
Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (MAP AND TARGET BOOSTER PRESSURE)
6.READ VALUE USING GTS (MAP AND TARGET BOOSTER PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Target Booster Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
Target Booster Pressure
50003 234 4,834

d.

Take a snapshot when the engine speed is maintained at 4500 rpm with no load.


e.

Read the values of "MAP" and "Target Booster Pressure" in the Data List using the snapshot review function.

Result:
Result Proceed to
Difference between MAP and Target Booster Pressure is +/-15 kPa or higher A
Except above B




A

7.CHECK CONNECTION OF VACUUM HOSE

B

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK CONNECTION OF VACUUM HOSE
a.

Check the turbocharger system vacuum hose connections.


Result:
Proceed to
OK
NG



OK

8.INSPECT VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL)

NG

26.REPAIR OR REPLACE VACUUM HOSE
8.INSPECT VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL)
a.

Inspect the vacuum regulating valve assembly (for turbocharger control).

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>VACUUM REGULATING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK TURBOCHARGER SUB-ASSEMBLY

NG

25.REPLACE VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL)
9.CHECK TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL) - ECM)

NG

24.REPLACE TURBOCHARGER SUB-ASSEMBLY
10.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL) - ECM)
a.

Disconnect the vacuum regulating valve assembly (for turbocharger control) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C91-2 - C39-108 (VN) Always Below 1 Ω
C91-2 or C39-108 (VN) - Body ground Always 10 kΩ or higher



d.

Reconnect the vacuum regulating valve assembly (for turbocharger control) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

11.CHECK DIESEL THROTTLE BODY ASSEMBLY

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.CHECK DIESEL THROTTLE BODY ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Actual Throttle Position and Actual Throttle Position #2.

Powertrain > Engine and ECT > Data List
Tester Display
Actual Throttle Position
Actual Throttle Position #2
50003 234 830,832

d.

Take a snapshot when accelerating with the accelerator fully depressed.


e.

Read the value of "Actual Throttle Position" and "Actual Throttle Position #2" in the Data List using the snapshot review function.

Result:

The value for "Actual Throttle Position" and "Actual Throttle Position #2" is 0%.



Result:
Proceed to
OK
NG



OK

12.CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

16.REPLACE DIESEL THROTTLE BODY ASSEMBLY
12.CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Actual EGR Valve Pos.

Powertrain > Engine and ECT > Data List
Tester Display
Actual EGR Valve Pos
50003 234 822

d.

Take a snapshot when accelerating with the accelerator fully depressed.


e.

Read the value of "Actual EGR Valve Pos." in the Data List using the snapshot review function.

Result:

The value for "Actual EGR Valve Pos." is 0%.



Result:
Proceed to
OK
NG



OK

13.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EGR COOLER BYPASS)

NG

20.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
13.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EGR COOLER BYPASS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off and wait for 30 seconds.


d.

Start the engine and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 234 3

f.

Read the MAF value displayed on the tester while the engine is idling.


g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / EGR Cooler Bypass Position and MAF.

HINT:

Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.


Powertrain > Engine and ECT > Active Test
Active Test Display
Activate the VSV for EGR Cooler Bypass
Data List Display
MAF
EGR Cooler Bypass Position
50004 234 181 3,793

h.

Using the Active Test function, switch the EGR valve bypass switching valve between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".

HINT:

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.


Result:
Tester Display Result Proceed to
Activate the VSV for EGR Cooler Bypass: Cooler to Bypass MAF value does not change A
MAF value changes B


HINT:
·

If the EGR cooler is clogged, the mass air flow changes.

·

If the bypass valve does not mechanically switch even with no clogging in the EGR cooler, the intake air flow will not change.

The bypass valve switch is determined by negative pressure changes and operating sound.


·

If the bypass valve does not mechanically switch, perform the repairs listed below and replace the part. Then check for changes in the intake air flow by performing the Active Test again.






A

14.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8)

B

17.REPLACE EGR COOLER SUB-ASSEMBLY
14.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #8.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 234 778,779,780,781,782,783,784,785

e.

Read the values.

Standard Value:
Item Engine Speed* Reference Value
Injection Feedback Val #1 to #8 Idling -3.0 to 3.0 mm3/st


HINT:
·

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.

·

When the values are outside the standard range, deposits inside the injector assemblies may be causing the problem.



OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

15.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0234 AND/OR P1251)

NG

21.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
15.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0234 AND/OR P1251)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and warm it up for 1 minute or more.


g.

Turn the GTS on.


h.

Read the value of Engine Speed from the freeze frame data recorded previously.

HINT:

When performing the DTC detection drive pattern, make sure the engine speed increases to 2400 rpm or more and exceeds the "Engine Speed" value from the freeze frame data.



i.

After warming up the engine, drive the vehicle at a constant vehicle speed at an engine speed of 2400 rpm or more for 2 minutes.


j.

With the engine warmed up, fully depress the accelerator pedal for 5 seconds or more so that the engine speed is 2400 rpm or more.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

Powertrain > Engine and ECT > Trouble Codes
50001 234

l.

Read the DTC.

Result:
Proceed to
DTC is not output
DTC P0234 and/or P1251 is output




DTC is not output

END

DTC P0234 and/or P1251 is output

18.REPLACE ECM
16.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly (Bank 1 or Bank 2).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.REPLACE EGR COOLER SUB-ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
a.

Replace the fuel injector.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

22.BLEED AIR FROM FUEL SYSTEM
22.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration.

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.


Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

23.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
23.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
24.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
25.REPLACE VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL)
a.

Replace the vacuum regulating valve assembly (for turbocharger control).

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>VACUUM REGULATING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
26.REPAIR OR REPLACE VACUUM HOSE
a.

Repair or replace the vacuum hose.


Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and warm it up.


g.

Turn the GTS on.


h.

Read the value of Engine Speed from the freeze frame data recorded previously.

HINT:

When performing the DTC detection drive pattern, make sure the engine speed increases to 2400 rpm or more and exceeds the "Engine Speed" value from the freeze frame data.



i.

After warming up the engine, drive the vehicle at a constant vehicle speed at an engine speed of 2400 rpm or more for 2 minutes [A].


j.

With the engine warmed up, fully depress the accelerator pedal for 5 seconds or more so that the engine speed is 2400 rpm or more [B].


k.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P0234 or P1251.


iii.

Check that STATUS is NORMAL.

HINT:
·

If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.

·

If STATUS is INCOMPLETE or N/A, perform [A] and [B] again.





Result:
Proceed to
NEXT



NEXT

END