MALFUNCTION DESCRIPTION
The EV control ECU detects a stuck closed malfunction of a system main relay on the positive (+) terminal side and negative (-) terminal side of the EV supply battery assembly.
The cause of this malfunction may be one of the following:
Voltage sensor (VH) malfunction
Motor generator control ECU (MG ECU) malfunction
Communication (wire harness) malfunction
No. 1 EV battery junction block assembly malfunction
FC converter assembly (FC stack main relay, FC precharge junction assembly) malfunction
EV control ECU malfunction
No. 1 EV battery junction block assembly malfunction
Low voltage wire harness malfunction
Low voltage connector malfunction
FC converter assembly (FC precharge junction assembly) malfunction
Refer to the description for DTC P0AE411.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411
This circuit uses the EV control ECU to monitor the system main relays and stops the system if a malfunction is detected in the relays, because it may be impossible to shut off the high-voltage system if any of the relays becomes stuck.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P0AA073 | Hybrid/EV Battery Positive and Negative Contactor Actuator Stuck Closed | Even both of the system main relays (EV supply battery assembly positive (+) and negative (-) terminal side) are turned off, the inverter voltage (VH) does not drop.
(1 trip detection logic) |
·
No. 1 EV battery junction block assembly ·
Inverter with converter assembly ·
EV control ECU ·
Wire harness or connector |
Master Warning:
Comes on |
EV | A |
| DTC No. | Data List |
|---|---|
| P0AA073 | ·
Hybrid/EV Battery Voltage ·
VH-Voltage after Boosting ·
VL-Voltage before Boosting ·
FCDC Output Voltage |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 10 minutes or more.
Turn the ignition switch to ON (READY) and wait for 2 minutes or more.
According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 100 V, the vehicle has returned to normal.
Enter the following menus: Powertrain / EV / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Refer to the wiring diagram for the HV battery high-voltage line circuit.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.
Make sure to remove the service plug grip first.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the EV supply battery assembly
Disconnecting the low voltage connector of the FC converter assembly
To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.
The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.
Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.
| *a | Without waiting for 10 minutes |
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.
If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.
After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
If the DTCs are cleared or the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal before performing repairs, turning the ignition switch to ON (READY) may cause a malfunction. Do not turn the ignition switch to ON (READY).
Do not turn the ignition switch to ON with the service plug grip removed, as this may cause a malfunction.
If DTC P0AA073 is output, do not install the service plug grip before completing repair.
If the service plug grip is not removed, the EV suplly battery assembly will gradually discharge and the SOC will decrease.
If DTC P0AA073 is output, the ignition switch cannot be turned to ON (READY).
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0AA073 only is output, or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Microcomputer malfunction | P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
| P060687 | Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message | |
| P060A47 | Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure | |
| P060A87 | Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message | |
| P0A1B49 | Drive Motor "A" Control Module Internal Electronic Failure | |
| P1C9E9F | Hybrid/EV System Reset Stuck Off | |
| P0A1B1F | Drive Motor "A" Control Module Circuit Intermittent | |
| P1CB038 | Drive Motor "A" Position Sensor REF Signal Frequency Incorrect | |
| P1C2B00 | Drive Motor "A" Control Module A/D Processing Performance | |
| P0A1B04 | Drive Motor "A" Control Module System Internal Failure | |
| P1CA700 | Drive Motor "A" Control Module RAM/ROM Error | |
| P1CAD49 | Drive Motor "A" Position Sensor Internal Electronic Failure | |
| P1D0400 | FC Air Compressor Motor Control Module A/D Processing Performance | |
| P1D0500 | FC Air Compressor Motor Control Module RAM/ROM Error | |
| P1D8F04 | FC Air Compressor Motor Control Module System Internal Failure | |
| P1D8F47 | FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure | |
| P1D8F49 | FC Air Compressor Motor Control Module Internal Electronic Failure | |
| P1E8649 | FC Air Compressor Motor Position Sensor Internal Electronic Failure | |
| P1C731C | Sensor Reference Voltage "H" Circuit/Open Circuit Voltage Out of Range | |
| P1E3B87 | Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message | |
| Power source circuit malfunction | P06D61C | Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range |
| P06B01C | Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range | |
| P06E61C | Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range | |
| Communication system malfunction | P312387 | Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
| Sensor and actuator circuit malfunction | P0AD911 | Hybrid/EV Battery Positive Contactor Circuit Short to Ground |
| P0AD915 | Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open | |
| P0ADD11 | Hybrid/EV Battery Negative Contactor Circuit Short to Ground | |
| P0ADD15 | Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open | |
| P0AE411 | Hybrid/EV Battery Precharge Contactor Circuit Short to Ground | |
| P0AE415 | Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open | |
| P0A3F16 | Drive Motor "A" Position Sensor Circuit Voltage Below Threshold | |
| P0A1B00 | Drive Motor "A" Control Module Performance | |
| P1CB038 | Drive Motor "A" Position Sensor REF Signal Frequency Incorrect | |
| P1CB300 | Drive Motor "A" Position Sensor REF Signal Oscillation Stop | |
| P0A3F16 | Drive Motor "A" Position Sensor Circuit Voltage Below Threshold | |
| P0A3F22 | Drive Motor "A" Position Sensor Signal Amplitude > Maximum | |
| P0A3F1C | Drive Motor "A" Position Sensor Circuit Voltage Out of Range | |
| P1D8F00 | FC Air Compressor Motor Control Module Performance | |
| P1E8738 | FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect | |
| P1E8800 | FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop | |
| P1D7516 | FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold | |
| P1D7522 | FC Air Compressor Motor Position Sensor Signal Amplitude > Maximum | |
| P1D751C | FC Air Compressor Motor Position Sensor Circuit Voltage Out of Range | |
| P1E9011 | FC Positive Contactor Control Circuit Short to Ground | |
| P1E9015 | FC Positive Contactor Control Circuit Short to Battery or Open | |
| P1E9211 | FC Precharge Contactor Control Circuit Short to Ground | |
| P1E9215 | FC Precharge Contactor Control Circuit Short to Battery or Open | |
| P1E9111 | FC Negative Contactor Control Circuit Short to Ground | |
| P1E9115 | FC Negative Contactor Control Circuit Short to Battery or Open | |
| System malfunction | P0D2D1C | Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range |
| P1C8349 | High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction | |
| P0C7600 | Hybrid/EV Battery System Discharge Time Too Long | |
| P0D2D16 | Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold | |
| P0D2D17 | Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold | |
| P1CB69E | Drive Motor "A" Inverter Overvoltage Signal Stuck On | |
| P1E1500 | FC Positive Contactor Actuator Stuck Closed | |
| P1E1773 | FC Negative Contactor Control Actuator Stuck Closed | |
| P1E1573 | FC Positive and Negative Contactor Actuator Stuck Closed | |
P0AA073 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
None.
Procedure1
Read the freeze frame data of DTC P0AA073.
| Tester Display | Measurement Item | Range |
|---|---|---|
| VL-Voltage before Boosting | High voltage before it is boosted | - |
| VH-Voltage after Boosting | High voltage after it is boosted | - |
| Tester Display |
|---|
| VL-Voltage before Boosting |
| VH-Voltage after Boosting |
As freeze frame data is stored immediately before and after a DTC is stored, make sure to only read the values for the moment the DTC was stored ("0(s)").
| Result | Proceed to |
|---|---|
| Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is less than 42 V. | A |
| Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is 42 V or more. | B |
If VH-Voltage after Boosting is output even when an off command is being sent to the system main relay (positive side), P0AA073 is output. If the difference between the "VL-Voltage before Boosting" and the "VH-Voltage after Boosting" is large, it is determined that there is an inverter (VH sensor) malfunction.
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK (for LHD) |
| OK (for RHD) |
| NG |
OK (for LHD)
OK (for RHD)
NG
Pre-procedure1
None.
Procedure1
Read the freeze frame data of DTC P0AA073.
| Tester Display | Measurement Item | Range |
|---|---|---|
| VH-Voltage after Boosting | High voltage after it is boosted | - |
| FCDC Output Voltage | FC converter power module transistor (FC boost converter) output voltage sensor value | - |
| Tester Display |
|---|
| VH-Voltage after Boosting |
| FCDC Output Voltage |
As freeze frame data is stored immediately before and after a DTC is stored, make sure to only read the values for the moment the DTC was stored ("0(s)").
| Result | Proceed to |
|---|---|
| Difference between "VH-Voltage after Boosting" and "FCDC Output Voltage" is less than 37 V. | A |
| Difference between "VH-Voltage after Boosting" and "FCDC Output Voltage" is 37 V or more. | B |
If VH-Voltage after Boosting is output even when an off command is being sent to the system main relay (positive side), P0AA073 is output. If the difference between the "VL-Voltage before Boosting" and the "VH-Voltage after Boosting" is large, it is determined that there is an inverter (VH sensor) malfunction.
Post-procedure1
Turn the ignition switch off.
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Check the connection condition of the G156 No. 2 EV battery pack wire connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connector.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 10 EV battery shield panel.
Disconnect the z24 No. 1 EV battery junction block assembly connector.
Disconnect the G14*1 or A14*2 EV control ECU connector.
*1: for LHD
*2: for RHD
Procedure1
| *A | for LHD |
| *B | for RHD |
| *a | Rear view of wire harness connector
(to EV Control ECU) |
| *b | Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G14,z24)Location & Routingewd_type=routing;type=c,c;code=G14,z24 Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECUewd_type=component;type=c;code=G14;pinno=4,2,14 Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assemblyewd_type=component;type=c;code=z24;pinno=1,4,2 |
||
| G14-4 (SMRB) - z24-1 (SMRB) | Ignition switch off | Below 1 Ω |
| G14-2 (SMRG) - z24-4 (SMRG) | Ignition switch off | Below 1 Ω |
| G14-14 (SMRP) - z24-2 (SMRP) | Ignition switch off | Below 1 Ω |
| G14-4 (SMRB) or z24-1 (SMRB) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| G14-2 (SMRG) or z24-4 (SMRG) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| G14-14 (SMRP) or z24-2 (SMRP) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A14,z24)Location & Routingewd_type=routing;type=c,c;code=A14,z24 Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A14;pinno=4,2,14 Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assemblyewd_type=component;type=c;code=z24;pinno=1,4,2 |
||
| A14-4 (SMRB) - z24-1 (SMRB) | Ignition switch off | Below 1 Ω |
| A14-2 (SMRG) - z24-4 (SMRG) | Ignition switch off | Below 1 Ω |
| A14-14 (SMRP) - z24-2 (SMRP) | Ignition switch off | Below 1 Ω |
| A14-4 (SMRB) or z24-1 (SMRB) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| A14-2 (SMRG) or z24-4 (SMRG) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| A14-14 (SMRP) or z24-2 (SMRP) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the G14*1 or A14*2 EV control ECU connector.
*1: for LHD
*2: for RHD
Reconnect the z24 No. 1 EV battery junction block assembly connector.
Install the No. 10 EV battery shield panel.
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 10 EV battery shield panel.
Disconnect the z24 No. 1 EV battery junction block assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(No. 1 EV Battery Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z24)Location & Routingewd_type=routing;type=c;code=z24 Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assemblyewd_type=component;type=c;code=z24;pinno=1,3,4,2 |
||
| z24-1 (SMRB) - z24-3 (GND) | -40 to 80°C (-40 to 176°F) | 25.0 to 59.0 Ω |
| z24-4 (SMRG) - z24-3 (GND) | -40 to 80°C (-40 to 176°F) | 25.0 to 59.0 Ω |
| z24-2 (SMRP) - z24-3 (GND) | -40 to 80°C (-40 to 176°F) | 140 to 290 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the z24 No. 1 EV battery junction block assembly connector.
Install the No. 10 EV battery shield panel.
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 10 EV battery shield panel.
Disconnect the N1 and N2 floor under wire connectors from the No. 1 EV battery junction block assembly.
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
Disconnect the EV supply battery assembly high voltage connector from the No. 1 EV battery junction block assembly.
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(No. 1 EV Battery Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z13,N1)Location & Routingewd_type=routing;type=c,c;code=z13,N1 Click Connector(z13)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assemblyewd_type=component;type=c;code=z13;pinno=1 Click Connector(N1)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assemblyewd_type=component;type=c;code=N1;pinno=1 |
||
| z13-1 (+) - N1-1 (CBI) | Ignition switch off | 10 kΩ or higher |
If a system main relay is stuck closed, inspect the No. 1 EV battery junction block assembly without removing it from the vehicle, in order to keep the relay closed.
If the result of reading the freeze frame data is A, the No. 1 EV battery junction block assembly must be replaced. Measuring resistance can determine that this is either a present or past malfunction.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(No. 1 EV Battery Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z12,N2)Location & Routingewd_type=routing;type=c,c;code=z12,N2 Click Connector(z12)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assemblyewd_type=component;type=c;code=z12;pinno=1 Click Connector(N2)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assemblyewd_type=component;type=c;code=N2;pinno=1 |
||
| z12-1 (-) - N2-1 (CEI) | Ignition switch off | 10 kΩ or higher |
If a system main relay is stuck closed, inspect the No. 1 EV battery junction block assembly without removing it from the vehicle, in order to keep the relay closed.
If the result of reading the freeze frame data is A, the No. 1 EV battery junction block assembly must be replaced. Measuring resistance can determine that this is either a present or past malfunction.
If the resistance is between 24.3 and 29.7 Ω, it can be determined that SMRP is stuck closed.
| Result | Judgment | Proceed to |
|---|---|---|
| OK | Past malfunction | A |
| NG | Present malfunction | B |
Post-procedure1
Reconnect the EV supply battery assembly high voltage connector.
Reconnect the N1 and N2 floor under wire connectors.
Install the No. 10 EV battery shield panel.
A
B
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Be sure to wear insulated gloves.
Pre-procedure1
install the service plug grip.
Procedure1
Clear the DTCs and freeze frame data.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for 10 minutes or more.
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Result | Proceed to |
|---|---|
| Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is always less than 100 V. | A |
| None of the above conditions are met | B |
A
B
EV control ECU: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL
No. 1 EV battery junction block assembly: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL