Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1E0A12  FC Converter Fail Signal Circuit Short to Battery  P1E0A14  FC Converter Fail Signal Circuit Short to Ground or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU detects a malfunction in the system shut-off signal (ISDN signal) which is sent from the FCDC converter control ECU.

The likely causes of the malfunction are as follows.

ISDN signal circuit malfunction
·

Wire harness malfunction

·

FCDC converter control ECU malfunction

·

EV control ECU malfunction


HSDN signal circuit malfunction
·

Wire harness malfunction

·

Inverter with converter assembly malfunction

·

EV control ECU malfunction



DESCRIPTION

For the HSDN signal system description, refer to the DTC P321E9F.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P321E9F

For the FSDN and ISDN signal system description, refer to the DTC P1D9512.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1D9512

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E0A12 FC Converter Fail Signal Circuit Short to Battery The FSDN signal from the EV control ECU is OFF but the CPU monitored value of the HSDN signal is ON.
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

FCDC converter control ECU board sub-assembly

·

FC converter power module transistor

·

Inverter with converter assembly


Master Warning:
Comes on
EV A
P1E0A14 FC Converter Fail Signal Circuit Short to Ground or Open The FSDN signal from the EV control ECU is ON but the CPU monitored value of the HSDN signal is OFF.
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

FCDC converter control ECU board sub-assembly

·

FC converter power module transistor

·

Inverter with converter assembly


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P1E0A12
P1E0A14
·

Emergency Shutdown Signal (FC)

·

FC Converter Shutdown Signal

·

Inverter Emergency Shutdown (Main CPU)

·

Inverter Emergency Shutdown (Sub CPU)



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch off and wait for 10 minutes or more.

2.

Turn the ignition switch to ON (READY) and wait for 30 seconds.

3.

Turn the ignition switch off and wait for 10 minutes or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

For the HSDN signal system circuit diagram, refer to the shutdown signal system.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Shut Down Signal Circuit

For the FSDN and ISDN signal system circuit diagrams, refer to P1D9512.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1D9512

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV, FCDC)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
P1E0A12 or P1E0A14 only is output, or DTCs except the ones in the table below are also output. A
DTCs of EV control system in the tables below are output. B
DTCs of FC boost control system in the tables below are output. C

Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P060B1C Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range
P1C9E9F Hybrid/EV System Reset Stuck Off
FC control system P060B16 Internal Control Module A/D Processing Performance Circuit Voltage Below Threshold
Power source circuit malfunction FC control system P1F451F FC Converter Control Module Power Relay Sense Circuit Intermittent
P1F651C FC Converter Control Module Power Supply (-5V) Circuit Voltage Out of Range
P1F661C FC Converter Control Module Power Supply (+V5AREF) Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
FC control system U116087 Lost Communication with FCDC Control Module Missing Message
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message
System malfunction Hybrid control system P321E9F Motor/Generator Shutdown Signal Stuck Off
P33B99F Motor/Generator Shutdown Signal (Hybrid/EV Side) Stuck Off
FC control system P1DDA9E FC Converter Phase U Fail Signal Stuck On
P1DDB9E FC Converter Phase V Fail Signal Stuck On
P1DDC9E FC Converter Phase W Fail Signal Stuck On
P1DDD9E FC Converter Phase X Fail Signal Stuck On
P1F0117 FC Converter Output Voltage Circuit Voltage Above Threshold
P1F009E FC Converter Overvoltage Signal Stuck On


HINT:
·

The chart above is listed in inspection order of priority.

·

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

2.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed to FC stack assembly and EV battery.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A17 EV control ECU connector.


c.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A480870C04
1.125,0.479 1.563,0.854 0.438,0.375 5.594,0.427 6.021,0.76 0.427,0.333 1.854,0.479 2.292,0.854 0.438,0.375 6.167,2.354 5.938,1.948 true 2.073,2.25 1.604,1.51 true 0.646,0.146 0.958,0.302 0.313,0.156 10 false *a 3.875,0.198 4.188,0.354 0.313,0.156 10 false *b 1.24,0.594 1.698,0.792 0.458,0.198 10 false A19 5.688,0.51 6.146,0.708 0.458,0.198 10 false A17 2.083,2.292 2.698,2.49 0.615,0.198 10 false HSDN 6.073,2.385 6.688,2.583 0.615,0.198 10 false HSDN 1.969,0.583 2.427,0.781 0.458,0.198 10 false A18 1.615,0.583 1.844,0.781 0.229,0.198 10 false *A 2.354,0.583 2.583,0.781 0.229,0.198 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to EV control ECU)


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,A19)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A17-8 (HSDN) - A19-25 (HSDN) Ignition switch off Below 1 Ω
A17-8 (HSDN) or A19-25 (HSDN) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,A18)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A17-8 (HSDN) - A18-25 (HSDN) Ignition switch off Below 1 Ω
A17-8 (HSDN) or A18-25 (HSDN) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


b.

Reconnect the A17 EV control ECU connector.



OK

5.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.
C256313C61
1.906,0.146 2.406,0.365 0.5,0.219 1.177,0.135 1.677,0.354 0.5,0.219 0.927,1.844 1.156,0.938 true 1.906,1.854 1.271,0.948 true 2.24,1.833 1.865,1.125 true 1.542,1.854 1.281,1.188 true 0.156,0.104 0.469,0.26 0.313,0.156 10 false *a 1.24,0.167 1.885,0.323 0.646,0.156 10 false A19*A 0.802,1.865 1.115,2.021 0.313,0.156 10 false +B2 1.896,1.865 2.208,2.021 0.313,0.156 10 false +B 2.208,1.865 2.719,2.021 0.51,0.156 10 false HSDN 1.438,1.875 1.833,2.031 0.396,0.156 10 false GND1 1.969,0.177 2.615,0.333 0.646,0.156 10 false A18*B
*A for LHD
*B for RHD
*a Component without harness connected
(Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-25 (HSDN) - A19-30 (GND1) Ignition switch off 2.65 to 3.55 kΩ
A19-25 (HSDN) - A19-10 (+B) Ignition switch off 5 kΩ or higher
A19-25 (HSDN) - A19-11 (+B2) Ignition switch off 5 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-25 (HSDN) - A18-30 (GND1) Ignition switch off 2.65 to 3.55 kΩ
A18-25 (HSDN) - A18-10 (+B) Ignition switch off 5 kΩ or higher
A18-25 (HSDN) - A18-11 (+B2) Ignition switch off 5 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

6.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

6.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A16 EV control ECU connector.


c.

Remove the electric heater sub-assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL



d.
A481473

Disconnect the B6 FC converter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A480871C01
1.688,0.281 2.094,0.594 0.406,0.313 5.146,0.438 5.604,0.771 0.458,0.333 5.844,2.406 5.458,2 true 2.563,2.417 2.021,1.271 true 0.542,0.26 0.854,0.458 0.313,0.198 10 false *a 3.219,0.292 3.531,0.49 0.313,0.198 10 false *b 1.823,0.375 2.281,0.573 0.458,0.198 10 false B6 2.5,2.448 3.052,2.667 0.552,0.219 10 false ISDN 5.271,0.531 5.729,0.729 0.458,0.198 10 false A16 5.813,2.438 6.365,2.656 0.552,0.219 10 false ISDN
*a Front view of wire harness connector
(to FC Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B6,A16)Location & Routing

Click Connector(B6)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

B6-4 (ISDN) - A16-20 (ISDN) Ignition switch off Below 1 Ω
B6-4 (ISDN) or A16-20 (ISDN) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B6 FC converter assembly connector.


b.

Install the electric heater sub-assembly.


c.

Reconnect the A16 EV control ECU connector.



OK

8.CHECK FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY (+B, GND SHORT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY (+B, GND SHORT)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the electric heater sub-assembly connector.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL



c.
A481473

Disconnect the B6 FC converter assembly connector.


Procedure1

a.
A491111C02
1.458,0.396 1.948,0.802 0.49,0.406 1.052,2.688 1.469,1.979 true 1.417,2.667 1.646,1.979 true 2.01,2.656 1.823,1.948 true 2.323,2.656 1.99,1.948 true 2.531,2.177 1.833,1.479 true 0.823,2.198 1.646,1.635 true 0.854,1.792 1.469,1.469 true 1.625,0.521 1.938,0.719 0.313,0.198 10 false B6 0.5,1.719 1.115,1.917 0.615,0.198 10 false ISDN 1.979,2.667 2.26,2.865 0.281,0.198 10 false E1 2.583,2.177 3.198,2.375 0.615,0.198 10 false DRN0 0.573,2.177 1.188,2.375 0.615,0.198 10 false IG2 2.365,2.667 2.635,2.865 0.271,0.198 10 false E2 0.802,2.677 1.167,2.875 0.365,0.198 10 false +B2 1.26,2.677 1.635,2.885 0.375,0.208 10 false +B1 0.26,0.385 0.875,0.583 0.615,0.198 10 false *a
*a Component without harness connected
(FC Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B6)Location & Routing

Click Connector(B6)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

B6-4 (ISDN) - B6-10 (E1) Ignition switch off 2.65 to 3.55 kΩ
B6-4 (ISDN) - B6-12 (+B1) Ignition switch off 5 kΩ or higher
B6-4 (ISDN) - B6-2 (DRN0) Ignition switch off 10 kΩ or higher
B6-4 (ISDN) - B6-11 (E2) Ignition switch off 10 kΩ or higher
B6-4 (ISDN) - B6-13 (+B2) Ignition switch off 5 kΩ or higher
B6-4 (ISDN) - B6-6 (IG2) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B6 FC converter assembly connector.


b.

Install the electric heater sub-assembly connector.



OK

9.INSPECT EV CONTROL ECU (RESISTANCE VALUE OF ISDN INSIDE EV CONTROL ECU)

NG

12.REMOVE FC CONVERTER ASSEMBLY
9.INSPECT EV CONTROL ECU (RESISTANCE VALUE OF ISDN INSIDE EV CONTROL ECU)

Pre-procedure1

a.
A481473

Disconnect the B6 FC converter assembly connector.


Procedure1

a.
A478491C63
1.99,0.75 2.438,1.094 0.448,0.344 1.406,0.75 1.854,1.094 0.448,0.344 2.219,1.677 2.396,2.417 true 1.771,1.823 1.49,2.427 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.104,0.844 2.406,1.01 0.302,0.167 10 false A17 2.354,2.448 2.615,2.604 0.26,0.156 10 false E1 1.521,0.854 1.823,1.021 0.302,0.167 10 false A16 1.271,2.448 1.823,2.635 0.552,0.188 10 false ISDN
*a Component with harness connected
(EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A17)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-20 (ISDN) - A17-4 (E1) Ignition switch off 2.65 to 3.55 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B6 FC converter assembly connector.



OK

10.REMOVE FC CONVERTER ASSEMBLY

NG

10.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.REPLACE FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY
11.REPLACE FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY

NEXT

REPLACE FC CONVERTER POWER MODULE TRANSISTOR

12.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.REPLACE FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY
13.REPLACE FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY

NEXT

REPLACE FC CONVERTER POWER MODULE TRANSISTOR