Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1F0117  FC Converter Output Voltage Circuit Voltage Above Threshold  


DESCRIPTION

Refer to high voltage system diagram for the System Description.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION

The FC converter assembly increases the FC stack voltage up to approximately DC650 V. Then the inverter converts the high-voltage direct current of the FC converter into alternating current and drives the motor.

The FC boost control ECU detects high voltage before boosting (FVL) and high voltage after boosting (FVH) using the voltage sensor, which is located inside the FC converter assembly. The FC boost control ECU controls the operation of the FC converter assembly based on the voltage before and after boosting, and controls the FC stack current and voltage to become the target values.

A478992E01
0.021,0.281 1.427,0.458 1.406,0.177 10 false FC Stack Assembly 1.99,0.292 3.521,0.49 1.531,0.198 10 false FC Converter Assembly 4.448,0.281 6.583,0.458 2.135,0.177 10 false Inverter with Converter Assembly 6.479,1.958 7.135,2.271 0.656,0.313 10 false Motor Generator 4.542,2.802 5.583,2.958 1.042,0.156 10 false Boost Converter 0.01,4.281 1.802,4.458 1.792,0.177 10 false Before boosting direct current 1.635,3.167 2.865,3.323 1.229,0.156 10 false Voltage Conversion 3.01,4.313 4.771,4.531 1.76,0.219 10 false After boosting direct current 5.042,4.323 7.156,4.521 2.115,0.198 10 false After converting alternating current

If an overvoltage occurs in the motor inverter or FC air compressor motor inverter, the FC boost control ECU detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1F0117 FC Converter Output Voltage Circuit Voltage Above Threshold The FC converter output voltage (FVH) is detected to be too high. (Overvoltage)
(1 trip detection logic)
·

FCV transaxle with motor assembly

·

FC air compressor with motor assembly

·

FC converter assembly

·

Inverter with converter assembly

·

EV battery junction block assembly

·

No. 1 frame wire

·

Service plug grip (for EV) (EV battery fuse)

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on FCDC B

Related Data List
DTC No. Data List
P1F0117 FC Converter Output Voltage

WIRING DIAGRAM

Refer to the wiring diagram for the motor resolver circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Motor Resolver Circuit

Refer to the wiring diagram for the FC air compressor resolver circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>FC Air Compressor Resolver Circuit

Refer to the wiring diagram for the high-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Refer to the wiring diagram for the inverter low-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Inverter Low-voltage Circuit

Refer to the wiring diagram for the FC boost converter low-voltage circuit.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>ECU Power Source Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

Drive the vehicle in a city area under the vehicle and driving conditions based on the recorded freeze frame data for approximately 10 minutes.



PROCEDURE

1.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
Only P1F0117 is output A
P1F0117 and DTCs other than the DTCs in the table below are output B
P1F0117 and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Microcomputer malfunction P060B16 Internal Control Module A/D Processing Performance Circuit Voltage Below Threshold
P060B1C Internal Control Module A/D Processing Performance Circuit Voltage Out of Range
P060B49 Internal Control Module A/D Processing Performance Internal Electronic Failure
P060B71 Internal Control Module A/D Processing Performance Actuator Stuck
P1F451F FC Converter Control Module Power Relay Sense Circuit Intermittent
Power source circuit malfunction P1F661C FC Converter Control Module Power Supply (+V5AREF) Circuit Voltage Out of Range
Sensor and actuator circuit malfunction P1D1C16 FC Converter Output Voltage Sensor Circuit Voltage Below Threshold
P1D1C17 FC Converter Output Voltage Sensor Circuit Voltage Above Threshold
P1D2017 FC Converter Input Voltage Sensor Circuit Voltage Above Threshold
P1D3011 Phase U Reactor Current Sensor Circuit Short to Ground
P1D3015 Phase U Reactor Current Sensor Circuit Short to Battery or Open
P1D301C Phase U Reactor Current Sensor Circuit Voltage Out of Range
P1D3028 Phase U Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3511 Phase V Reactor Current Sensor Circuit Short to Ground
P1D3515 Phase V Reactor Current Sensor Circuit Short to Battery or Open
P1D351C Phase V Reactor Current Sensor Circuit Voltage Out of Range
P1D3528 Phase V Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3A11 Phase W Reactor Current Sensor Circuit Short to Ground
P1D3A15 Phase W Reactor Current Sensor Circuit Short to Battery or Open
P1D3A1C Phase W Reactor Current Sensor Circuit Voltage Out of Range
P1D3A28 Phase W Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D4011 Phase X Reactor Current Sensor Circuit Short to Ground
P1D4015 Phase X Reactor Current Sensor Circuit Short to Battery or Open
P1D401C Phase X Reactor Current Sensor Circuit Voltage Out of Range
P1D4028 Phase X Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D4A14 Phase V Temperature Sensor Circuit Short to Ground or Open
P1D4F62 Total Reactor Current/FC Current Signal Compare Failure
P1D0618 FC Converter Phase U Current Circuit Current Below Threshold
P1D0718 FC Converter Phase V Current Circuit Current Below Threshold
P1D0818 FC Converter Phase W Current Circuit Current Below Threshold
P1D0918 FC Converter Phase X Current Circuit Current Below Threshold
System malfunction P1D0619 FC Converter Phase U Current Circuit Current Above Threshold
P1D0719 FC Converter Phase V Current Circuit Current Above Threshold
P1D0819 FC Converter Phase W Current Circuit Current Above Threshold
P1D0919 FC Converter Phase X Current Circuit Current Above Threshold
P1DDA4B FC Converter Phase U Over Temperature
P1DDB4B FC Converter Phase V Over Temperature
P1DDC4B FC Converter Phase W Over Temperature
P1DDD4B FC Converter Phase X Over Temperature
P1D0E62 Inverter Output Voltage/FC Converter Output Voltage Signal Compare Failure
P1D0F62 Cell Monitor Voltage/FC Converter Input Voltage Signal Compare Failure
P1DDA9E FC Converter Phase U Fail Signal Stuck On
P1DDB9E FC Converter Phase V Fail Signal Stuck On
P1DDC9E FC Converter Phase W Fail Signal Stuck On
P1DDD9E FC Converter Phase X Fail Signal Stuck On
P1DDA00 FC Converter Phase U Performance
P1DDB00 FC Converter Phase V Performance
P1DDC00 FC Converter Phase W Performance
P1DDD00 FC Converter Phase X Performance


HINT:

DTC P1F0117 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (EV)

B

2.CHECK DTC OUTPUT (EV)

C

GO TO DTC CHART

2.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Microcomputer malfunction P0A1B00 Drive Motor "A" Control Module Performance
P0A1B04 Drive Motor "A" Control Module System Internal Failure
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P1CB300 Drive Motor "A" Position Sensor REF Signal Oscillation Stop
P1E8649 FC Air Compressor Motor Position Sensor Internal Electronic Failure
P1E8800 FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop
P1E8738 FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect
Sensor and actuator circuit malfunction P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A3F1C Drive Motor "A" Position Sensor Circuit Voltage Out of Range
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum
P1D7516 FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold
P1D751C FC Air Compressor Motor Position Sensor Circuit Voltage Out of Range
P1D7522 FC Air Compressor Motor Position Sensor Signal Amplitude > Maximum
P0BE91C Drive Motor "A" Phase V Current Sensor "A" Circuit Voltage Out of Range
P1C3C62 Drive Motor "A" Phase V Current Sensor "A"/"B" Signal Compare Failure
P1C491C Drive Motor "A" Phase V Current Sensor "B" Circuit Voltage Out of Range
P1C6D28 Drive Motor "A" Phase V Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure
P0BED1C Drive Motor "A" Phase W Current Sensor "A" Circuit Voltage Out of Range
P1C3D62 Drive Motor "A" Phase W Current Sensor "A"/"B" Signal Compare Failure
P1C4E1C Drive Motor "A" Phase W Current Sensor "B" Circuit Voltage Out of Range
P1C6E28 Drive Motor "A" Phase W Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure
P1E9362 FC Air Compressor Motor Phase V Current Sensor "A"/"B" Signal Compare Failure
P1F0E1C FC Air Compressor Motor Phase V Current Sensor "A" Circuit Voltage Out of Range
P1F101C FC Air Compressor Motor Phase V Current Sensor "B" Circuit Voltage Out of Range
P1F1228 FC Air Compressor Motor Phase V Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure
P1E9462 FC Air Compressor Motor Phase W Current Sensor "A"/"B" Signal Compare Failure
P1F0F1C FC Air Compressor Motor Phase W Current Sensor "A" Circuit Voltage Out of Range
P1F111C FC Air Compressor Motor Phase W Current Sensor "B" Circuit Voltage Out of Range
P1F1328 FC Air Compressor Motor Phase W Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure
P0A9300 Inverter "A" Cooling System Performance
P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure
P314A31 Motor Electronics Coolant Pump "A" No Signal
System malfunction P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P1C8449 High Voltage Power Resource Circuit Short during Ready ON
P1AC300 Drive Motor "A" Inverter Circuit Short (System Performance)
P1B2900 Drive Motor "A" Inverter Overcurrent (System Performance)
P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P1A8E00 Drive Motor "A" Inverter Overvoltage (Inverter Performance)
P0A784B Drive Motor "A" Inverter Over Temperature
P0A789E Drive Motor "A" Inverter Fail Signal Stuck On
P1ABF00 Drive Motor "A" Inverter Circuit Short (Inverter Performance)
P0C1900 Drive Motor "A" Torque Delivered Performance
P1A8400 Drive Motor "A" Inverter Overvoltage (Control Module Performance)
P1A8900 Drive Motor "A" Inverter Overvoltage (Position Sensor Circuit Range/Performance)
P1AB400 Drive Motor "A" Inverter Circuit Short (Control Module Performance)
P1AB900 Drive Motor "A" Inverter Circuit Short (Position Sensor Circuit Range/Performance)
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1AE400 Drive Motor "A" Inverter Overcurrent (Control Module Performance)
P1B1400 Drive Motor "A" Inverter Overcurrent (Inverter Performance)
P1AF900 Drive Motor "A" Inverter Overcurrent (Position Sensor Circuit Range/Performance)
P334F00 FC Air Compressor Inverter Overcurrent (Control Module Performance)
P337F00 FC Air Compressor Inverter Overcurrent (Inverter Performance)
P336F00 FC Air Compressor Inverter Overcurrent (Position Sensor Circuit Range/Performance)
P338F00 FC Air Compressor Inverter Overcurrent (System Performance)
P1E8E00 FC Air Compressor Motor Torque Delivered Performance
P1D824B FC Air Compressor Inverter Over Temperature
P1EF800 FC Air Compressor Inverter Circuit Short (Control Module Performance)
P1EFB00 FC Air Compressor Inverter Circuit Short (Inverter Performance)
P1EF900 FC Air Compressor Inverter Circuit Short (Position Sensor Circuit Range/Performance)
P1D829E FC Air Compressor Inverter Fail Signal Stuck On
P1EFA00 FC Air Compressor Inverter Circuit Short (System Performance)
P0BFF1D Drive Motor "A" Current Circuit Current Out of Range
P1F141D FC Air Compressor Motor Circuit Current Out of Range
P1AA900 DC/DC Converter "A" Overcurrent (System Performance)
P0CA300 DC/DC Converter Step Up Voltage Performance
P1A0F00 DC/DC Converter "A" Overvoltage (Control Module Performance)
P1A6F00 DC/DC Converter "A" Overvoltage (Inverter Performance)
P1A2F00 DC/DC Converter "A" Overvoltage (Position Sensor Circuit Range/Performance)
P0A944B DC/DC Converter "A" Over Temperature
P1A9400 DC/DC Converter "A" Overcurrent (Control Module Performance)
P1AA400 DC/DC Converter "A" Overcurrent (Inverter Performance)
P1A9900 DC/DC Converter "A" Overcurrent (Position Sensor Circuit Range/Performance)
P0A949E DC/DC Converter "A" Fail Signal Stuck On
P0E311C Boosting Converter Voltage Sensor "A" Voltage Out of Range
P1C2D62 Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure
P0E3116 DC/DC Converter Voltage Sensor "A" Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" Circuit Voltage Above Threshold
P0C7600 Hybrid/EV Battery System Discharge Time Too Long
P33B99F Motor/Generator Shutdown Signal (Hybrid/EV Side) Stuck Off


HINT:

DTC P1F0117 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

4.CHECK FC AIR COMPRESSOR MOTOR RESOLVER

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FC AIR COMPRESSOR MOTOR RESOLVER

NEXT

5.CHECK MOTOR RESOLVER CIRCUIT
5.CHECK MOTOR RESOLVER CIRCUIT

NEXT

6.CHECK FC AIR COMPRESSOR HIGH-VOLTAGE CIRCUIT
6.CHECK FC AIR COMPRESSOR HIGH-VOLTAGE CIRCUIT

NEXT

7.CHECK MOTOR HIGH-VOLTAGE CIRCUIT
7.CHECK MOTOR HIGH-VOLTAGE CIRCUIT

NEXT

8.CHECK EV BATTERY HIGH-VOLTAGE LINE CIRCUIT
8.CHECK EV BATTERY HIGH-VOLTAGE LINE CIRCUIT

NEXT

9.CHECK INVERTER LOW-VOLTAGE CIRCUIT
9.CHECK INVERTER LOW-VOLTAGE CIRCUIT

NEXT

10.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)
10.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

11.CHECK FC CONVERTER ASSEMBLY (FC CONVERTER POWER OUTLET CABLE CONNECTION CONDITION)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK FC CONVERTER ASSEMBLY (FC CONVERTER POWER OUTLET CABLE CONNECTION CONDITION)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0E62

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems There are no arc marks A
The terminals are not connected securely and there is a contact problem There are arc marks B
The terminals are connected securely and there are no contact problems There are arc marks
The terminals are not connected securely and there is a contact problem There are no arc marks C



A

12.REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

12.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

13.CLEAR DTC
13.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > FCDC > Clear DTCs
50002 493
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

14.CHECK DTC OUTPUT (FCDC)
14.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


b.

Drive the vehicle in a city area under the vehicle and driving conditions based on the recorded freeze frame data for approximately 10 minutes.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493

Result:
Result Proceed to
P1F0117 is output A
DTCs are not output B


Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE FC CONVERTER ASSEMBLY

B

END