Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1CCC96  DC/DC Converter Enable Component Internal Failure  


DESCRIPTION

The DC/DC converter converts the DC 310.8 V of the EV supply battery assembly into DC 12 V in order to supply power to areas such as the vehicle lighting system, audio system and various ECUs. Additionally, it charges the auxiliary battery.

A transistor bridge circuit initially converts DC 310.8 V into alternating current, and a transformer lowers the voltage. Then, it is rectified and smoothed (into direct current) and converted into DC 12 V.

The DC/DC converter controls the output voltage in order to keep a constant voltage at the terminals of the auxiliary battery.

The EV control ECU sends a signal to the DC/DC converter to prohibit its control and receives signals indicating a normal or abnormal condition of the 12 V charging system via the NODD signal line.

If the DC/DC converter malfunctions, the vehicle will become inoperative. Therefore, the EV control ECU monitors the operation of the DC/DC converter and detects malfunctions.

This DTC is stored when the DC/DC converter circuit has a malfunction or its operation is prohibited by a fail-safe function, or the auxiliary battery voltage drops to 11 V or less with the ignition switch ON (READY).

If a DC/DC converter malfunction occurs, DC/DC converter malfunction signals are sent from the DC/DC converter to the EV control ECU via the NODD signal line.

This DTC may also be stored if a malfunction of the inverter cooling system (blockage, water pump malfunction, etc.) or a high-voltage insulation malfunction occurs.

C373945E03
1.073,1 1.844,1.198 0.771,0.198 10 false DC/DC 0.948,2.292 1.719,2.49 0.771,0.198 10 false DC/DC-S 0.354,3.906 1.813,4.104 1.458,0.198 10 false from Auxiliary Battery 2.406,2.458 3.74,2.646 1.333,0.188 10 false DC/DC Converter 2.042,0.917 2.5,1.094 0.458,0.177 10 false AMD 5.26,0.323 6.031,0.521 0.771,0.198 10 false DC 310.8 V 3.927,2.219 4.135,2.396 0.208,0.177 10 false S 4.125,2.219 4.583,2.396 0.458,0.177 10 false NODD 4.615,2.219 4.948,2.396 0.333,0.177 10 false VLO 5.042,2.219 5.375,2.396 0.333,0.177 10 false IDH 5.385,2.219 5.844,2.396 0.458,0.177 10 false IGCT 2,3.5 4.167,3.688 2.167,0.188 10 false Inverter with Converter Assembly 3.938,4.469 5.292,4.719 1.354,0.25 10 false EV Control ECU 6.365,2.469 7.104,2.833 0.74,0.365 10 false from IGCT NO.3 Fuse

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1CCC96 DC/DC Converter Enable Component Internal Failure Either of the following conditions is met:
·

The DC/DC converter is malfunctioning and the auxiliary battery voltage is 11 V or less.*

·

The DC/DC converter is malfunctioning and inverter coolant temperature is 70°C (154°F) or less for 60 seconds.


(1 trip detection logic)
·

Fusible link block assembly

·

DC/DC-S Fuse

·

Inverter bus-bar plate sub-assembly

·

Inverter cooling system

·

Cooling fan system

·

Inverter with converter assembly

·

No. 2 battery pack wire

·

FC air compressor cable

·

EV control ECU

·

Wire harness or connector


Master Warning:
Comes on
EV A

HINT:

*: If the DC/DC converter is malfunctioning, its operation and charging will be stopped and the auxiliary battery voltage will drop.


WIRING DIAGRAM

for LHD:
A480862E02
1.281,0.896 2.219,1.094 0.938,0.198 10 false R/B RR#2 4.271,1.729 5.208,2.146 0.938,0.417 10 false Luggage Room Relay Block 4.406,1.458 5.344,1.656 0.938,0.198 10 false DC/DC-S 1.365,1.458 1.969,1.656 0.604,0.198 10 false R/B FR 2.719,1.469 3.656,1.667 0.938,0.198 10 false R/B RR#1 4.25,0.198 5.698,0.406 1.448,0.208 10 false from Auxiliary Battery 1.167,1.802 3.552,2.063 2.385,0.26 10 false No. 2 Fusible Link Block Assembly 1.042,3.135 3.792,3.396 2.75,0.26 10 false No. 2 Front Compartment Relay Block 2.104,7.177 5.542,7.375 3.438,0.198 10 false EV Control ECU 5.646,7.167 6.99,7.594 1.344,0.427 10 false Inverter with Converter Assembly 2.177,4.448 3.115,4.646 0.938,0.198 10 false IGCT NO.2 1.135,3.885 2.073,4.083 0.938,0.198 10 false IGCT NO.2 1.99,2.802 2.594,3 0.604,0.198 10 false DC/DC 3.271,3.865 4.208,4.063 0.938,0.198 10 false IGCT NO.3 5.813,3.74 6.167,3.938 0.354,0.198 10 false IGCT 5.813,5.677 6.25,5.896 0.438,0.219 10 false NODD 5.813,2.625 6.167,2.823 0.354,0.198 10 false AMD 5.833,1.333 5.99,1.531 0.156,0.198 10 false S 5.438,1.313 5.792,1.51 0.354,0.198 10 false A20 5.521,2.635 5.688,2.833 0.167,0.198 10 false A 5.448,3.719 5.802,3.917 0.354,0.198 10 false A20 5.448,5.771 5.802,5.969 0.354,0.198 10 false A20 4.229,5.771 4.646,5.969 0.417,0.198 10 false A17 4.25,5.302 4.688,5.479 0.438,0.177 10 false A8 4.219,6.729 4.688,6.927 0.469,0.198 10 false A17 3.75,2.646 4.104,2.844 0.354,0.198 10 false 2A 3.76,1.323 4.115,1.521 0.354,0.198 10 false J7 0.646,0.74 1,0.938 0.354,0.198 10 false J6 0.635,1.313 0.99,1.51 0.354,0.198 10 false N4 0.625,2.646 0.979,2.844 0.354,0.198 10 false 2B 0.667,0.531 0.823,0.729 0.156,0.198 10 false 1 0.667,1.104 0.823,1.302 0.156,0.198 10 false 1 0.667,2.427 0.823,2.625 0.156,0.198 10 false 1 3.792,1.115 3.948,1.313 0.156,0.198 10 false 1 3.792,2.438 3.948,2.635 0.156,0.198 10 false 1 5.531,1.115 5.688,1.313 0.156,0.198 10 false 3 5.531,2.438 5.688,2.635 0.156,0.198 10 false 1 5.531,3.521 5.688,3.719 0.156,0.198 10 false 1 5.531,5.573 5.688,5.771 0.156,0.198 10 false 5 4.271,5.573 4.521,5.771 0.25,0.198 10 false 18 4.323,6.531 4.531,6.729 0.208,0.198 10 false 4 3.719,5.292 4.125,5.51 0.406,0.219 10 false MREL 3.719,5.667 4.146,5.865 0.427,0.198 10 false NODD 3.26,5.948 3.677,6.115 0.417,0.167 10 false 100 Ω 2.688,6.313 3.104,6.479 0.417,0.167 10 false 47 kΩ 2.688,6.656 3.104,6.823 0.417,0.167 10 false 82 kΩ 3.927,6.729 4.156,6.927 0.229,0.198 10 false E1 2.042,4.083 2.198,4.281 0.156,0.198 10 false 1 2.833,4.083 2.99,4.281 0.156,0.198 10 false 2 2.031,3.635 2.188,3.833 0.156,0.198 10 false 3 2.833,3.635 2.99,3.833 0.156,0.198 10 false 5 4.25,2.948 5.427,3.313 1.177,0.365 10 false No. 1 Fusible Link Block Assembly 5.063,2.448 5.219,2.646 0.156,0.198 10 false 1 4.25,2.458 4.406,2.656 0.156,0.198 10 false 1 4.979,2.646 5.333,2.844 0.354,0.198 10 false z27 4.156,2.646 4.51,2.844 0.354,0.198 10 false A40 4.531,1.177 4.688,1.375 0.156,0.198 10 false 1 4.771,1.177 4.927,1.375 0.156,0.198 10 false 2 4.271,5.083 4.521,5.281 0.25,0.198 10 false 21

for RHD:
A480862E03
1.26,0.885 2.198,1.083 0.938,0.198 10 false R/B RR#2 4.208,1.74 5.135,2.208 0.927,0.469 10 false Luggage Room Relay Block 4.406,1.479 5.344,1.677 0.938,0.198 10 false DC/DC-S 1.344,1.448 1.948,1.646 0.604,0.198 10 false R/B FR 2.708,1.469 3.646,1.667 0.938,0.198 10 false R/B RR#1 4.25,0.188 5.698,0.396 1.448,0.208 10 false from Auxiliary Battery 1.167,1.792 3.552,2.052 2.385,0.26 10 false No. 2 Fusible Link Block Assembly 1.083,3.135 3.688,3.438 2.604,0.302 10 false No. 2 Front Compartment Relay Block 2.094,7.198 5.531,7.396 3.438,0.198 10 false EV Control ECU 5.656,7.177 7.021,7.594 1.365,0.417 10 false Inverter with Converter Assembly 2.167,4.458 3.104,4.656 0.938,0.198 10 false IGCT NO.2 1.115,3.885 2.052,4.083 0.938,0.198 10 false IGCT NO.2 1.99,2.802 2.594,3 0.604,0.198 10 false DC/DC 3.229,3.875 4.167,4.073 0.938,0.198 10 false IGCT NO.3 5.813,3.719 6.167,3.917 0.354,0.198 10 false IGCT 5.802,5.667 6.24,5.885 0.438,0.219 10 false NODD 5.813,2.635 6.167,2.833 0.354,0.198 10 false AMD 5.833,1.313 5.99,1.51 0.156,0.198 10 false S 5.448,1.313 5.802,1.51 0.354,0.198 10 false A20 5.521,2.646 5.688,2.844 0.167,0.198 10 false A 5.448,3.719 5.802,3.917 0.354,0.198 10 false A20 5.448,5.781 5.802,5.979 0.354,0.198 10 false A20 4.229,5.781 4.646,5.979 0.417,0.198 10 false A17 4.219,5.302 4.656,5.479 0.438,0.177 10 false D15 4.208,6.729 4.677,6.927 0.469,0.198 10 false A17 3.75,2.635 4.104,2.833 0.354,0.198 10 false 3A 3.771,1.313 4.125,1.51 0.354,0.198 10 false J7 0.625,0.74 0.979,0.938 0.354,0.198 10 false J6 0.635,1.302 0.99,1.5 0.354,0.198 10 false N4 0.615,2.646 0.969,2.844 0.354,0.198 10 false 3B 0.667,0.531 0.823,0.729 0.156,0.198 10 false 1 0.667,1.104 0.823,1.302 0.156,0.198 10 false 1 0.667,2.438 0.823,2.635 0.156,0.198 10 false 1 3.792,1.104 3.948,1.302 0.156,0.198 10 false 1 3.792,2.438 3.948,2.635 0.156,0.198 10 false 1 5.521,1.115 5.677,1.313 0.156,0.198 10 false 3 5.521,2.438 5.677,2.635 0.156,0.198 10 false 1 5.521,3.51 5.677,3.708 0.156,0.198 10 false 1 5.531,5.573 5.688,5.771 0.156,0.198 10 false 5 4.25,5.594 4.5,5.792 0.25,0.198 10 false 18 4.302,6.531 4.51,6.729 0.208,0.198 10 false 4 3.729,5.302 4.135,5.521 0.406,0.219 10 false MREL 3.708,5.667 4.135,5.865 0.427,0.198 10 false NODD 3.25,5.958 3.667,6.125 0.417,0.167 10 false 100 Ω 2.688,6.313 3.104,6.479 0.417,0.167 10 false 47 kΩ 2.688,6.656 3.104,6.823 0.417,0.167 10 false 82 kΩ 3.917,6.719 4.146,6.917 0.229,0.198 10 false E1 2.042,4.083 2.198,4.281 0.156,0.198 10 false 1 2.833,4.083 2.99,4.281 0.156,0.198 10 false 2 2.031,3.635 2.188,3.833 0.156,0.198 10 false 3 2.833,3.635 2.99,3.833 0.156,0.198 10 false 5 4.167,2.948 5.344,3.313 1.177,0.365 10 false No. 1 Fusible Link Block Assembly 5.063,2.427 5.219,2.625 0.156,0.198 10 false 1 4.25,2.438 4.406,2.635 0.156,0.198 10 false 1 4.99,2.646 5.344,2.844 0.354,0.198 10 false z27 4.156,2.646 4.51,2.844 0.354,0.198 10 false A40 4.531,1.177 4.688,1.375 0.156,0.198 10 false 1 4.76,1.177 4.917,1.375 0.156,0.198 10 false 2 4.271,5.104 4.521,5.302 0.25,0.198 10 false 21

Refer to the wiring diagram for the FC Air Compressor High-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>FC Air Compressor High-voltage Circuit

Refer to the wiring diagram for the Motor High-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Motor High-voltage Circuit

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


·

After repair, clear the DTCs, turn the ignition switch off and wait for 10 minutes or more and perform the following procedure to confirm that the auxiliary battery low voltage indicated by this DTC has been repaired.

(a)

Wait for 2 minutes with park (P) selected, the ignition switch to ON (READY) and the following conditions met, then confirm that Data List item "Auxiliary Battery Voltage (Hybrid control system)" is between 13.0 and 15.0 V.

(If charging is not performed and the electrical load increases, +B voltage may not be steady and will gradually drop.)

(1)

Headlight switch is in the HI position.

(2)

A/C blower fan switch is in the HI position.

(3)

Window defogger switch is turned on.


(b)

Enter the following menus: Powertrain / EV / Utility / All Readiness.

(c)

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.





CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

This DTC may be also stored when a part other than the DC/DC converter is malfunctioning or depending on user operation.


·

If this vehicle is used to jump start another vehicle with a discharged battery, a fuse may blow due to overcurrent or the DC/DC converter self-protection may be activated. Also, if this vehicle is jump started by a vehicle with a 24 V battery, the same malfunction may occur and this DTC may be stored. (The suspended DC/DC converter control will return to normal by clearing the DTCs and turning the ignition switch off.)


·

Confirm that high electrical load equipment such as a high-capacitance audio device or electric kettle is used in the vehicle. (A fuse of the auxiliary battery may be blown due to overcurrent.)


·

If the DC/DC converter is malfunctioning, the auxiliary battery cannot be charged. Therefore, once the ignition switch is turned off, it may be impossible to turn it to ON (READY) again if the auxiliary battery is completely discharged. In this case, charge the auxiliary battery. Be careful as charging is not performed during the inspection.


·

If the ignition switch turns off immediately after it is turned to ON (READY), the auxiliary battery voltage may be low. Charge the auxiliary battery.



PROCEDURE

1.CHECK DTC OUTPUT

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1CCC96 only is output, or DTCs except the ones in the table below are also output. A
DTCs of EV control system in the table below are output. B


Malfunction Content Relevant DTC
Insulation Malfunction P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure
High Voltage Circuit Malfunction P0AA649 Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure
P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P1C8449 High Voltage Power Resource Circuit Short during Ready ON
P300449 High Voltage Power Resource Circuit Short during Pre-Charge
System malfunction P1A7F00 DC/DC Converter "A" Overvoltage (System Performance)
P0A9300 Inverter "A" Cooling System Performance
P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure
P314A31 Motor Electronics Coolant Pump "A" No Signal

HINT:

P1CCC96 may be output as a result of the malfunction indicated by the DTCs above.

1.

The chart above is listed in inspection order of priority.

2.

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FUSE (DC/DC-S)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK FUSE (DC/DC-S)

Pre-procedure1

a.

Remove the DC/DC-S fuse from the luggage room relay block.


Procedure1

a.
A480863C01
1.313,2.135 1.625,2.74 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *1 1.677,2.76 1.99,2.917 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 DC/DC-S Fuse


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DC/DC-S fuse terminal 1 - 2 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the DC/DC-S fuse.



OK

3.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

NG

15.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - LUGGAGE ROOM RELAY BLOCK)
3.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

5.CHECK FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)

Pre-procedure1

a.

Check the fusible link block assembly (DC/DC) for improper installation.

OK:

The fusible link block assembly is installed securely.



b.

Remove the fusible link block assembly from the No. 2 Front Compartment relay block and junction block.


Procedure1

a.
C449861C04
0.135,0.479 0.531,0.781 0.396,0.302 0.135,0.865 0.531,1.167 0.396,0.302 2.75,1.135 3.146,1.438 0.396,0.302 2.76,1.51 3.156,1.813 0.396,0.302 0.615,1.271 0.885,0.896 true 2.667,1.01 3.083,0.594 true 0.135,0.125 0.448,0.281 0.313,0.156 10 false *1 0.5,1.26 0.656,1.458 0.156,0.198 10 false 1 3.167,0.427 3.323,0.625 0.156,0.198 10 false 1 0.25,0.552 0.688,0.75 0.438,0.198 10 false 2B 2.865,1.208 3.146,1.427 0.281,0.219 10 false 2A 0.25,0.948 0.688,1.146 0.438,0.198 10 false 3B 2.885,1.583 3.156,1.781 0.271,0.198 10 false 3A 0.573,0.552 1.01,0.75 0.438,0.198 10 false *A 0.573,0.917 1.01,1.115 0.438,0.198 10 false *B 3.188,1.198 3.365,1.406 0.177,0.208 10 false *A 3.208,1.573 3.385,1.781 0.177,0.208 10 false *B
*A for LHD
*B for RHD
*1 Fusible Link Block Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
2B-1 - 2A-1 Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
3B-1 - 3A-1 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the fusible link block assembly.



OK

6.CHECK AMD TERMINAL VOLTAGE (NO. 1 FUSIBLE LINK BLOCK ASSEMBLY SIDE)

NG

REPLACE FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)

6.CHECK AMD TERMINAL VOLTAGE (NO. 1 FUSIBLE LINK BLOCK ASSEMBLY SIDE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


Procedure1

a.
A492127C01
2.448,0.938 2.854,1.281 0.406,0.344 0.26,3.135 0.667,3.479 0.406,0.344 2.531,1.021 2.802,1.219 0.271,0.198 10 true z27 0.052,0.063 0.271,0.26 0.219,0.198 10 true *A 0.063,2.448 0.281,2.646 0.219,0.198 10 true *B 0.344,3.208 0.615,3.406 0.271,0.198 10 true z27
*A for LHD
*B for RHD


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z27)Location & Routing

Click Connector(z27)Engine Compartment>other>No. 1 Fusible Link Block Assembly , Inverter Bus-Bar Plate Sub-Assembly

z27-1 (AMD) - Body ground Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.



OK

7.CHECK AMD TERMINAL CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK AMD TERMINAL CONNECTION CONDITION
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A483133C03
0.052,0.052 0.25,0.25 0.198,0.198 10 true *A 0.042,2.479 0.24,2.677 0.198,0.198 10 true *B
*A for LHD
*B for RHD


Check that the bolt for the AMD terminal (inverter with converter assembly side and No. 1 fusible link block assembly side) is tightened to the specified torque, the AMD terminal (inverter with converter assembly side and No. 1 fusible link block assembly side) is connected securely, and there is no contact problem.

Torque:

T = 18.0 N*m (184 kgf*cm, 13 ft.*lbf) (Inverter with converter assembly side)

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf) (No. 1 fusible link block assembly side)


Result:
Result Proceed to
There are no arc marks. The terminal is connected securely and there are no contact problems. A
There are no arc marks. The terminal is not connected securely and there is a contact problem. B
There are arc marks. - C



Post-procedure1

a.

None.



A

8.CHECK INVERTER BUS-BAR PLATE SUB-ASSEMBLY

B

CONNECT SECURELY

C

REPLACE MALFUNCTIONING PARTS

8.CHECK INVERTER BUS-BAR PLATE SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the inverter bus-bar plate sub-assembly from the AMD terminal (inverter with converter assembly side and No. 1 fusible link block assembly side).


Procedure1

a.
A489592C01
0.521,1.469 0.958,1.865 0.438,0.396 2.354,0.833 2.792,1.229 0.438,0.396 0.313,3.438 0.75,3.833 0.438,0.396 2.667,2.792 3.104,3.188 0.438,0.396 0.646,0.26 0.958,0.458 0.313,0.198 10 false *A 0.417,3.563 0.729,3.76 0.313,0.198 10 false z27 0.125,0.156 0.438,0.354 0.313,0.198 10 false *1 0.375,2.76 0.688,2.958 0.313,0.198 10 false *B 2.844,2.917 3.156,3.115 0.313,0.198 10 false A 0.646,1.583 0.958,1.781 0.313,0.198 10 false z27 2.531,0.938 2.844,1.135 0.313,0.198 10 false A
*A for LHD
*B for RHD
*1 Inverter Bus-bar Plate Sub-assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z27)Location & Routing

Click Connector(z27)Engine Compartment>other>No. 1 Fusible Link Block Assembly , Inverter Bus-Bar Plate Sub-Assembly

A-1 (AMD) - z27-1 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the inverter bus-bar plate sub-assembly.



OK

9.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - DC/DC-S FUSE)

NG

REPLACE INVERTER BUS-BAR PLATE SUB-ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - DC/DC-S FUSE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A20 inverter with converter assembly connector.


Procedure1

a.
C257160C70
1.521,0.135 1.948,0.458 0.427,0.323 1.104,0.698 1.583,0.896 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.625,0.24 1.99,0.427 0.365,0.188 10 false A20 0.938,0.594 1.51,0.833 0.573,0.24 10 false S
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A20)Location & Routing

Click Connector(A20)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A20-3 (S) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A20 inverter with converter assembly connector.



OK

10.CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF NODD INSIDE EV CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF NODD INSIDE EV CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A20 inverter with converter assembly connector.


Procedure1

a.
C257160C71
1.5,0.156 1.948,0.458 0.448,0.302 1.99,1.094 2.469,1.292 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.625,0.229 1.99,0.417 0.365,0.188 10 false A20 2.531,1.229 3.104,1.469 0.573,0.24 10 false NODD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A20)Location & Routing

Click Connector(A20)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A20-5 (NODD) - Body ground Ignition switch off 110 to 150 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A20 inverter with converter assembly connector.



OK

11.CHECK COOLING SYSTEM

NG

13.INSPECT EV CONTROL ECU (RESISTANCE VALUE OF NODD INSIDE EV CONTROL ECU)
11.CHECK COOLING SYSTEM

NEXT

12.INSPECT DC / DC CONVERTER
12.INSPECT DC / DC CONVERTER
CAUTION:

Measure the current flowing at the auxiliary battery instead.


Pre-procedure1

a.

Connect the AC/DC 400 A probe of the tester to the positive (+) auxiliary battery cable.


b.

Install the service plug grip.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.
A111747C29
0.792,0.979 1.083,0.583 1.083,0.583 1.167,0.583 true 0.833,1.667 0.917,1.667 0.917,1.667 1.167,1.25 true 1.208,0.5 1.625,0.708 0.417,0.208 10 false *a 0.677,1.583 1.177,1.781 0.5,0.198 10 false *b 0.583,0.833 1,1.042 0.417,0.208 10 false *c
*a Probe Direction
*b Current Flowing to Auxiliary Battery
*c Check the AC/DC 400 A probe is installed in the correct direction (positive (+) and negative (-))


Turn the ignition switch to ON (READY) and leave the vehicle as it is until the electric current flowingto the auxiliary battery becomes 10 A or less.

HINT:

If the ignition switch turns off immediately after it is turned to ON (READY), auxiliary batteryvoltage may be low. Recharge the auxiliary battery and perform this procedure again.



Procedure1

a.

Measure the current flowing from the auxiliarybattery with the ignition switch to ON (READY), theheadlight position switch and blower motor switchin the HI position, and the rear window defoggerturned on.


b.
A111748C19
0.792,0.979 1.083,0.583 1.083,0.583 1.167,0.583 true 0.833,1.667 0.917,1.667 0.917,1.667 1.167,1.25 true 1.208,0.5 1.625,0.708 0.417,0.208 10 false *a 0.677,1.583 1.177,1.781 0.5,0.198 10 false *b 0.604,0.802 1.021,1.01 0.417,0.208 10 false *c
*a Probe Direction
*b Current Flowing from Auxiliary Battery
*c Check the AC/DC 400 A probe is installed in the correct direction (positive (+) and negative (-))


Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Current flowing from auxiliary battery Ignition switch ON (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
0 A or less
(no current from auxiliary battery)



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery voltage Ignition switch ON (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
12.5 to 15 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

14.CHECK HIGH VOLTAGE INSULATION
13.INSPECT EV CONTROL ECU (RESISTANCE VALUE OF NODD INSIDE EV CONTROL ECU)

Pre-procedure1

a.

Disconnect all the connectors from the EV control ECU.


Procedure1

A478989C03
2.104,0.958 2.51,1.26 0.406,0.302 2.458,1.802 2.833,2.365 true 2.25,1.667 2.052,2.354 true 0.198,0.104 0.594,0.469 0.396,0.365 10 false *a 2.781,2.385 3.292,2.656 0.51,0.271 10 false NODD 2,2.365 2.333,2.594 0.333,0.229 10 false E1 2.208,1.042 2.49,1.292 0.281,0.25 10 false A17
*a Component without harness connected
(EV Control ECU)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-18(NODD) - A17-4(E1) Ignition switch off 110 to 150 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect theEV control ECU connectors.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

14.CHECK HIGH VOLTAGE INSULATION
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483161C01
0.042,0.042 0.354,0.24 0.313,0.198 10 true *A 0.042,2.479 0.354,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Remove the inverter terminal cover from the inverter with converter assembly.


Procedure1

a.
A484679C01
1.042,1.063 1.406,1.333 0.365,0.271 1.948,1.042 2.313,1.313 0.365,0.271 1.167,3.625 1.531,3.896 0.365,0.271 2.083,3.604 2.448,3.875 0.365,0.271 1.531,1.5 1.115,2.052 true 2.646,1.24 3.031,1.906 true 0.771,3.729 1.417,4.396 true 1.646,4.104 2.135,4.448 true 0.073,0.073 0.385,0.271 0.313,0.198 10 true *A 0.073,2.677 0.385,2.875 0.313,0.198 10 true *B 1.229,3.688 1.469,3.885 0.24,0.198 10 true O1 2.177,3.656 2.385,3.854 0.208,0.198 10 true o2 2.01,1.073 2.24,1.281 0.229,0.208 10 true O2 1.125,1.115 1.333,1.313 0.208,0.198 10 true o3 0.385,2.885 0.698,3.083 0.313,0.198 10 true *3 2.958,2.865 3.271,3.063 0.313,0.198 10 true *3 0.219,0.313 0.531,0.51 0.313,0.198 10 true *3 2.865,0.344 3.177,0.542 0.313,0.198 10 true *3 2.563,2.771 2.719,2.969 0.156,0.198 10 true U 0.74,0.24 0.896,0.438 0.156,0.198 10 true U 2.25,2.771 2.406,2.969 0.156,0.198 10 true V 1.083,0.219 1.24,0.417 0.156,0.198 10 true V 1.969,2.771 2.125,2.969 0.156,0.198 10 true W 1.354,0.229 1.51,0.427 0.156,0.198 10 true W 1.563,2.813 1.865,3 0.302,0.188 10 true R-U 1.625,0.25 1.927,0.438 0.302,0.188 10 true R-U 1.229,2.813 1.5,2.979 0.271,0.167 10 true R-V 2.01,0.26 2.281,0.427 0.271,0.167 10 true R-V 2.344,0.26 2.656,0.448 0.313,0.188 10 true R-W 0.865,2.813 1.177,3 0.313,0.188 10 true R-W 2.969,1.958 3.281,2.156 0.313,0.198 10 false *1 1.01,2.083 1.323,2.281 0.313,0.198 10 false *2 1.385,4.448 1.698,4.646 0.313,0.198 10 false *1 2.177,4.448 2.49,4.646 0.313,0.198 10 false *2
*A for LHD
*B for RHD
*1 No. 2 Battery Pack Wire
*2 FC Air Compressor Motor Cable Assembly
*3 Shield Ground


Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o3,O2)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

o3-1 (U) - Body ground and shield ground Ignition switch off 1 MΩ or higher
o3-2 (V) - Body ground and shield ground Ignition switch off 1 MΩ or higher
o3-3 (W) - Body ground and shield ground Ignition switch off 1 MΩ or higher
O2-1 (R-W) - Body ground and shield ground Ignition switch off 1 MΩ or higher
O2-2 (R-V) - Body ground and shield ground Ignition switch off 1 MΩ or higher
O2-3 (R-U) - Body ground and shield ground Ignition switch off 1 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o2,O1)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

o2-1 (W) - Body ground and shield ground Ignition switch off 1 MΩ or higher
o2-2 (V) - Body ground and shield ground Ignition switch off 1 MΩ or higher
o2-3 (U) - Body ground and shield ground Ignition switch off 1 MΩ or higher
O1-1 (R-W) - Body ground and shield ground Ignition switch off 1 MΩ or higher
O1-2 (R-V) - Body ground and shield ground Ignition switch off 1 MΩ or higher
O1-3 (R-U) - Body ground and shield ground Ignition switch off 1 MΩ or higher


HINT:

Perform this inspection while the motor cable are connected.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the inverter terminal cover to the inverter with converter assembly.



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

17.CHECK FC AIR COMPRESSOR HIGH-VOLTAGE CIRCUIT
15.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - LUGGAGE ROOM RELAY BLOCK)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A20 inverter with converter assembly connector.


c.

Remove the DC/DC-S fuse from the luggage room relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A480864C01
1.604,0.594 1.99,0.885 0.385,0.292 1.219,1.917 1.708,1.281 true 3.74,0.156 4.052,0.313 0.313,0.156 10 false *1 5.198,2.115 5.51,2.271 0.313,0.156 10 false *2 0.417,0.083 0.729,0.24 0.313,0.156 10 false *a 1.698,0.677 2.156,0.875 0.458,0.198 10 false A20 1.052,1.896 1.208,2.094 0.156,0.198 10 false S
*1 Luggage Room Relay Block *2 DC/DC-S Fuse
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A20)Location & Routing

Click Connector(A20)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A20-3 (S) or 2 (DC/DC-S fuse holder) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the DC/DC-S fuse.


b.

Reconnect the A20 inverter with converter assembly connector.



OK

16.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
16.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

REPLACE FUSE (DC/DC-S)

17.CHECK FC AIR COMPRESSOR HIGH-VOLTAGE CIRCUIT

NEXT

18.CHECK MOTOR HIGH-VOLTAGE CIRCUIT
18.CHECK MOTOR HIGH-VOLTAGE CIRCUIT

NEXT

REPLACE INVERTER WITH CONVERTER ASSEMBLY

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (DC/DC-S)