Home › Drivetrain › P510 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › 2011.12–2014.12
RM2170E _52 Drivetrain _057013 P510 HYBRID TRANSMISSION / TRANSAXLE _0277988 HYBRID VEHICLE TRANSAXLE A

P510 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  REMOVAL  


PROCEDURE

Hide 2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.REMOVE FRONT WHEELS

Hide 51442C 4.REMOVE ENGINE UNDER COVER LH

Hide 51441C 5.REMOVE ENGINE UNDER COVER RH

Hide 53301 9.REMOVE HOOD SUB-ASSEMBLY

a.
C249809

Remove the 4 bolts and hood sub-assembly from the hood hinge assembly LH and hood hinge assembly RH.


Hide 10.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55722C 11.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)

Hide 55722C 12.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)

Hide 55735B 13.REMOVE FRONT AIR SHUTTER SEAL (for LHD)

Hide 55735B 14.REMOVE FRONT AIR SHUTTER SEAL (for RHD)

Hide 55815E 15.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 16.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55701J 17.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 18.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide G9200 19.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 33820B 21.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C249710E02
1.156,1.51 1.385,1.51 true 2.594,1.333 2.833,1.333 true 1.427,1.438 1.625,1.625 0.198,0.188 10 true *1 2.865,1.26 3.063,1.458 0.198,0.198 10 true *2

Remove the nut, clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket and transmission control shaft lever.

Text in Illustration
*1 Transmission Control Cable Clamp
*2 Transmission Control Cable Support


b.

Disconnect the transmission control cable assembly from the transmission control cable clamp and transmission control cable support.


Hide 22.DISCONNECT WIRE HARNESS

a.
C249812

Disconnect the 4 clamps and No. 2 engine wire.


b.

Remove the 3 bolts and disconnect the 4 connectors, 7 clamps and wire harness from the hybrid vehicle transaxle assembly.

C354335


Hide 45259A 24.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45209 25.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45025D 26.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 17410 27.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 28.REMOVE FRONT DRIVE SHAFT ASSEMBLY

Hide 32.SUSPEND ENGINE ASSEMBLY

a.

Attach the sling device to the engine hangers and chain block.


Hide 51201 33.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 12364A 34.REMOVE ENGINE LATERAL CONTROL ROD

a.
C256842

Remove the 4 bolts and engine lateral control rod from the hybrid vehicle transaxle assembly.


Hide 30900 35.SUPPORT HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.

Support the hybrid vehicle transaxle assembly with a transmission jack.


Hide 12325A 36.REMOVE ENGINE MOUNTING BRACKET LH

a.
C251087

Remove the through bolt, nut and disconnect the engine mounting insulator LH from the engine mounting bracket LH.


b.

Remove the 4 bolts and engine mounting bracket LH from the hybrid vehicle transaxle assembly.


Hide 30900 37.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
U159487E03
1.01,2.375 0.75,2.375 true 2.521,0.479 2.833,0.479 true 2.552,0.771 2.656,0.771 2.656,0.771 2.656,0.479 true 0.563,2.302 0.75,2.51 0.188,0.208 10 true *2 2.865,0.385 3.063,0.573 0.198,0.188 10 true *1

Remove the 3 bolts, 2 wire harness clamp brackets and transmission control cable clamp from the hybrid vehicle transaxle assembly.

Text in Illustration
*1 Wire Harness Clamp Bracket
*2 Transmission Control Cable Clamp


b.
C249797

Remove the bolt, nut and drive shaft heat insulator sub-assembly from the engine and drive shaft heat insulator bracket.


c.
C249798

Disconnect the clamp from the drive shaft heat insulator bracket.


d.

Remove the 2 bolts and drive shaft heat insulator bracket from the engine.


e.
C249799

Remove the 2 bolts and starter hole heat insulator from the engine.


f.
C251104

Disengage the claw and remove the flywheel housing side cover from the engine.


g.
C250720

Remove the 6 bolts and hybrid vehicle transaxle assembly.

NOTICE:
·

To avoid damage to the knock pins, do not pry between the hybrid vehicle transaxle assembly and the engine.

·

To prevent the splines of the damper from becoming misaligned, do not allow the transaxle to hit the damper during transaxle removal and installation.




Hide G1250 38.REMOVE MOTOR COOLING PIPE ASSEMBLY

a.
C249801

Remove the bolt and oil cooler tube clamp from the No. 1 transmission control cable bracket.


b.
C249802E04
1.792,0.427 1.844,0.177 1.844,0.177 1.917,0.177 true 2.208,1.021 2.302,1.021 2.302,1.021 2.438,1.667 false 2.573,1.656 3.083,1.656 false 1.948,0.115 2.125,0.292 0.177,0.177 10 true *3 2.01,0.938 2.177,1.125 0.167,0.188 10 true *1 3.104,1.573 3.26,1.719 0.156,0.146 10 false *2

Using a union nut wrench, disconnect the motor cooling pipe assembly from the union.

Text in Illustration
*1 Flare Nut
*2 Union
*3 Union Bolt

HINT:

Turn the flare nut while holding the union.



c.

Remove the union bolt, gasket and motor cooling pipe assembly from the hybrid vehicle transaxle assembly.


d.
C249804

Remove the union and O-ring from the hybrid vehicle transaxle assembly.


Hide 33823 40.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C249805

Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.


Hide 35572D 41.REMOVE TRANSMISSION CONTROL SHAFT LEVER

a.
C250069

Remove the nut, washer, and transmission control shaft lever from the manual valve shaft.


Hide 89451A 42.REMOVE SHIFT LEVER POSITION SENSOR

HINT:

Perform this procedure only when replacement of the automatic transmission case cover is necessary.


a.
C250070E04
1.74,1.458 1.583,1.823 1.583,1.823 1.479,1.823 true 1.271,1.729 1.427,1.896 0.156,0.167 10 true *1

Using a screwdriver, pry the tabs of the lock plate.

Text in Illustration
*1 Lock Plate


b.
C250071E02
2.146,1.208 2.25,0.906 2.25,0.906 2.344,0.906 false 1.833,1.427 1.729,1.729 1.729,1.729 1.646,1.729 false 2.354,0.813 2.51,0.979 0.156,0.167 10 true *1 1.469,1.646 1.656,1.833 0.188,0.188 10 true *2

Remove the lock nut and lock plate from the manual valve shaft.

Text in Illustration
*1 Lock Nut
*2 Lock Plate


c.
C250072

Remove the 2 bolts and pull out the shift lever position sensor from the manual valve shaft.


Hide 35151J 43.REMOVE AUTOMATIC TRANSMISSION CASE COVER

HINT:

Perform this procedure only when replacement of the automatic transmission case cover is necessary.


a.
C249807

Remove the 2 bolts and automatic transmission case cover from the hybrid vehicle transaxle assembly.


Hide G1143 44.REMOVE MOTOR CABLE BRACKET

a.
C251000

Remove the bolt and motor cable bracket from the transmission control cable support.


Hide 33829 45.REMOVE TRANSMISSION CONTROL CABLE SUPPORT

a.
C251001

Remove the 3 bolts and 2 transmission control cable supports from the hybrid vehicle transaxle assembly.


Hide 46.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C251002

Remove the bolt and wire harness clamp bracket from the hybrid vehicle transaxle assembly.


Hide 30900H 47.REMOVE TRANSAXLE HSG AND CASE WITH HEAD STRAIGHT SCREW PLUG

a.
C249810

Remove the transaxle HSG and case with head straight screw plug and gasket from the hybrid vehicle transaxle assembly.