Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277948 ENGINE ASSEMBLY A

1NZ-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

The vehicle has a hybrid system that operates at voltages up to 650 V. The hybrid system uses an HV battery that contains an electrolyte which is a strong alkali solution that includes potassium hydroxide. Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may result in serious injury or electrocution (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 51442C 6.REMOVE ENGINE UNDER COVER LH

Hide 51441C 7.REMOVE ENGINE UNDER COVER RH

Hide 12.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55722C 13.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)

Hide 55722C 14.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)

Hide 55735B 15.REMOVE FRONT AIR SHUTTER SEAL (for LHD)

Hide 55735B 16.REMOVE FRONT AIR SHUTTER SEAL (for RHD)

Hide 55815E 17.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 18.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55701J 19.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 20.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide G9200 21.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 17705 22.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide G9110 24.REMOVE INVERTER BRACKET ASSEMBLY

CAUTION:

Wear insulated gloves.


a.
A268005

Remove the bolt and separate the motor cable protector.


b.
A268006

Disconnect the 2 wire harness clamps.


c.
A268007

Remove the 2 bolts and separate the inverter reservoir tank assembly.


d.
A268008

Remove the bolt and disconnect the earth wire.


e.
A268009

Remove the 4 bolts and inverter bracket assembly.


Hide 16571C 25.DISCONNECT NO. 1 RADIATOR HOSE

a.
A267997

Disconnect the No. 1 radiator hose from the engine assembly.


Hide 16572D 26.DISCONNECT NO. 2 RADIATOR HOSE

a.
A267996

Disconnect the No. 2 radiator hose from the engine assembly.


Hide 27.DISCONNECT HEATER WATER HOSE

a.
A267998

Disconnect the 2 heater water hoses from the engine assembly.


Hide 23820 28.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.
A267999

Disconnect the fuel vapor feed hose assembly.


Hide 23901 29.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 82121 30.DISCONNECT ENGINE WIRE (for LHD)

a.
A268000

Push the lock on the lever, then raise the lever, and disconnect the ECM connector.

NOTICE:

If there is any foreign matter such as mud or water on a connector, clean the connector.



b.

Disconnect the 2 wire harness clamps.


c.
A268004

Disconnect the 2 connectors and wire harness clamp.


d.

Using a screwdriver, disengage the claw and disconnect the engine wire from the engine room relay block and junction block assembly.


e.
A268002

Disconnect the engine wire from the engine room main wire.


f.

Disconnect the wire harness clamp.


Hide 82121 31.DISCONNECT ENGINE WIRE (for RHD)

a.
A268001

Push the lock on the lever, then raise the lever, and disconnect the ECM connector.

NOTICE:

If there is any foreign matter such as mud or water on a connector, clean the connector.



b.
A268003

Disconnect the 2 connectors and wire harness clamp.


c.

Using a screwdriver, disengage the claw and disconnect the engine wire from the engine room relay block and junction block assembly.


d.
A268002

Disconnect the engine wire from the engine room main wire.


e.

Disconnect the wire harness clamp.


Hide 33820B 32.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 33.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45259A 35.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45209 36.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45025D 37.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 88711 38.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88704 39.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88370 40.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

Hide 42.SEPARATE NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY

Hide 43.REMOVE FRONT DRIVE SHAFT ASSEMBLY

Hide 11361J 44.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A268016

Remove the flywheel housing under cover.


Hide 45.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A268010E01
0.502,0.044 0.662,0.194 0.160,0.149 10 *1 2.147,0.065 2.306,0.214 0.160,0.149 10 *2 3.194,0.877 3.353,1.026 0.160,0.149 10 *3 2.967,0.958 3.193,0.958 false 2.496,0.748 2.496,0.145 2.496,0.145 2.334,0.145 false 0.861,0.764 0.861,0.127 0.861,0.127 0.687,0.127 false

Set the engine lifter.

Text in Illustration
*1 No. 2 Oil Pan Sub-assembly
*2 Drain Plug
*3 Rear Cover Plug
V100145

Attachment Installation Position

NOTICE:
·

Place the height adjustment attachment and plate lift attachment so that the engine assembly with transaxle is level.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.

·

Do not place any attachments onto the drain plug and rear cover plug of the hybrid vehicle transaxle assembly.




b.
A270109

Remove the bolt and 2 nuts, and separate the engine mounting insulator sub-assembly RH from the engine assembly.


c.
A268011

Remove the bolt and nut, and separate the engine mounting insulator LH from the engine mounting bracket LH.


d.
A268012

Remove the 6 bolts, operate the engine lifter and slowly remove the engine assembly with transaxle and front suspension crossmember sub-assembly from the vehicle.

NOTICE:

Make sure that the engine is clear of all wiring and hoses.



Hide 12281A 46.INSTALL NO. 1 ENGINE HANGER

a.
A214905

Install the 2 No. 1 engine hangers with 2 new bolts.

Torque:
44 N*m (448 kgf*cm, 32 ft.*lbf)

Part Name Part No.
No. 1 engine hanger 12281-21090
Bolt 91672-81025


Hide 47.FIX ENGINE ASSEMBLY WITH TRANSAXLE

a.

Attach the sling device to the engine hangers and chain block.

NOTICE:

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.



b.
A268014E01
0.098,0.997 0.260,1.147 0.163,0.151 10 *1 2.118,0.157 2.281,0.307 0.163,0.151 10 *2 3.212,0.873 3.375,1.024 0.163,0.151 10 *3 0.531,1.082 0.278,1.082 false 2.966,0.958 3.204,0.958 false 2.496,0.746 2.496,0.24 2.496,0.24 2.312,0.24 false

To enable removal of the engine assembly, adjust the positions of the height adjustment attachment and plate lift attachment and set them in place.

Text in Illustration
*1 No. 2 Oil Pan Sub-assembly
*2 Drain Plug
*3 Rear Cover Plug
V100145

Attachment Installation Position

NOTICE:
·

Place the height adjustment attachment and plate lift attachment so that the engine assembly with transaxle is level.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.

·

Do not place any attachments onto the drain plug and rear cover plug of the hybrid vehicle transaxle assembly.




c.
A269294

Using a rope or belt, secure the engine assembly with transaxle to the engine lifter.

NOTICE:
·

Set the engine assembly with transaxle so that it is horizontal.

·

Do not tighten the rope or belt with a tightening mechanism or any more than is necessary.




Hide 48.REMOVE ENGINE ASSEMBLY

a.
C249812

Disconnect the 4 clamps and No. 2 engine wire.


b.

Remove the 3 bolts and disconnect the 4 connectors, 7 clamps and wire harness from the hybrid vehicle transaxle assembly.

C354335


c.
U159487E03
1.01,2.375 0.75,2.375 true 2.521,0.479 2.833,0.479 true 2.552,0.771 2.656,0.771 2.656,0.771 2.656,0.479 true 0.563,2.302 0.75,2.51 0.188,0.208 10 true *2 2.865,0.385 3.063,0.573 0.198,0.188 10 true *1

Remove the 3 bolts, 2 wire harness clamp brackets and transmission control cable clamp from the hybrid vehicle transaxle assembly.

Text in Illustration
*1 Wire Harness Clamp Bracket
*2 Transmission Control Cable Clamp


d.
C249797

Remove the bolt, nut and drive shaft heat insulator sub-assembly from the engine and drive shaft heat insulator bracket.


e.
C249798

Disconnect the clamp from the drive shaft heat insulator bracket.


f.

Remove the 2 bolts and drive shaft heat insulator bracket from the engine.


g.
C249799

Remove the 2 bolts and starter hole heat insulator from the engine.


h.
C251104

Disengage the claw and remove the flywheel housing side cover from the engine.


i.
C250720

Remove the 6 bolts and hybrid vehicle transaxle assembly.

NOTICE:
·

To avoid damage to the knock pins, do not pry between the hybrid vehicle transaxle assembly and the engine.

·

To prevent the splines of the damper from becoming misaligned, do not allow the transaxle to hit the damper during transaxle removal and installation.




Hide 31270 49.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

a.

Gently place the engine assembly onto wood blocks or equivalent.

NOTICE:
·

Set the engine assembly so that it is horizontal.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.

·

This step should be done while hanging the engine assembly using the sling device and chain block.




b.

Remove the transmission input damper assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>REMOVAL).


Hide 13405 50.REMOVE FLYWHEEL SUB-ASSEMBLY

a.

Gently place the engine assembly onto wood blocks or equivalent.

NOTICE:
·

Set the engine assembly so that it is horizontal.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.

·

This step should be done while hanging the engine assembly using the sling device and chain block.





Hide 12305 51.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A270110

Remove the 3 bolts and engine mounting insulator sub-assembly RH.


Hide 12372A 52.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A268018

Disconnect the wire harness clamp.


b.

Remove the 5 bolts and engine mounting insulator LH.


Hide 53.INSTALL ENGINE STAND

a.

Using a sling device and chain block, install the engine stand to the engine assembly.

NOTICE:
·

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.




Hide 82121 54.DISCONNECT ENGINE WIRE

a.

Disconnect all of the clamps and connectors and remove the engine wire from the engine assembly.


Hide 12281A 55.REMOVE NO. 1 ENGINE HANGER

a.

Remove the 2 bolts and 2 No. 1 engine hangers.