Home › Brake › BRAKE (REAR) › REAR DISC BRAKE PAD
RM3210E _54 Brake _047537 BRAKE (REAR) _0244654 REAR DISC BRAKE PAD A

BRAKE (REAR)  REAR DISC BRAKE PAD  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear disc brake pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE REAR WHEEL

Hide 46441 4.LOOSEN NO. 1 WIRE ADJUSTING NUT

Hide 47658B 5.REMOVE PARKING BRAKE LEVER PROTECTOR

Hide 46430 6.SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 47850 7.SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY

CAUTION:

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when removing the rear disc brake pads.


a.
C349642C01
1.396,0.719 1.708,0.875 0.313,0.156 10 false *a 0.375,1.844 0.688,2 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the rear disc brake pad guide pins and remove the bolt.


b.

Pull the rear disc brake cylinder assembly upward.


Hide 8.REMOVE ANTI SQUEAL SPRING

Hide 04466 9.REMOVE REAR DISC BRAKE PAD KIT

a.

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 10.REMOVE REAR DISC BRAKE ANTI SQUEAL SHIM KIT

Hide 04946 11.INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT

Hide 04466 12.INSTALL REAR DISC BRAKE PAD KIT

CAUTION:

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when installing the rear disc brake pads.


a.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.



Hide 13.INSTALL ANTI SQUEAL SPRING

Hide 47850 14.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C350148N01
1.26,1.875 2.104,1.875 true 2.135,1.802 2.594,2 0.458,0.198 10 false SST 1.031,3.302 1.313,3.479 0.281,0.177 10 true 90°

To compensate for pad lining thickness, use SST to adjust the protrusion of the rear disc brake piston by turning it.

SST
09719-12010  (09719-01030)

NOTICE:
·

Place the disc between the 2 brake pads and determine the piston return value.

·

Turn the rear disc brake piston to the position where the protrusion on the rear disc brake pad lines up properly with the piston groove.

·

Make sure the brake fluid does not overflow from the reservoir.




b.

Hold the rear disc brake pad guide pin and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the bolt.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Install the rear disc brake cylinder assembly while holding both of the rear disc brake pads because the anti-squeal springs may fall off the rear disc brake pads.

·

Be sure that the anti-squeal springs are installed to the rear disc brake pads.




Hide 46430 15.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 47658B 16.INSTALL PARKING BRAKE LEVER PROTECTOR

Hide 17.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION


c.

Turn the power switch on (READY).


d.

Depress the brake pedal and release it.



Hide 18.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Hide 19.ADJUST PARKING BRAKE

Hide 20.INSTALL REAR WHEEL