When replacing the injectors (including shuffling the injectors between the cylinders), common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipes with new ones.
When replacing the fuel supply pump assembly, common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.
43457
1.INSTALL DRIVE SHAFT BEARING BRACKET
Install the drive shaft bearing bracket with the 3 bolts.
17201
2.INSTALL TURBOCHARGER SUB-ASSEMBLY
25601L
3.INSTALL EGR COOLER WITH PIPE ASSEMBLY
16264
4.INSTALL NO. 2 WATER BY-PASS HOSE
25051
5.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
25509
6.INSTALL MANIFOLD CONVERTER INSULATOR SUB-ASSEMBLY
25589
7.INSTALL NO. 4 MANIFOLD CONVERTER INSULATOR
8.INSTALL NO. 1 WIRING HARNESS CLAMP BRACKET
25760A
9.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY
25860
10.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY
15481
11.INSTALL NO. 1 TURBO OIL PIPE
16279
12.INSTALL NO. 3 WATER BY-PASS PIPE
22100
13.INSTALL FUEL SUPPLY PUMP ASSEMBLY
Apply a light coat of engine oil to a new O-ring.
Install a new O-ring to the fuel supply pump assembly.
Install the No. 1 supply pump drive coupling.
When reusing the No. 1 supply pump drive coupling, it must be installed in the same orientation (top/bottom, front/back) as when it was removed.
Line up the No. 1 supply pump drive coupling with the groove in the camshaft end.
Install the fuel supply pump assembly with the 2 bolts.
Line up the end of the supply pump drive shaft with the No. 1 supply pump drive coupling.
23274D
14.INSTALL NO. 3 FUEL HOSE
23255B
15.INSTALL FUEL INJECTOR SEAL
23710B
16.INSTALL EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
23901E
17.INSTALL FUEL TUBE SUB-ASSEMBLY
23292A
18.INSTALL FUEL HOSE PROTECTOR
16278
19.INSTALL NO. 2 WATER BY-PASS PIPE
16281
20.INSTALL NO. 4 WATER BY-PASS HOSE
16296
21.INSTALL NO. 8 WATER BY-PASS HOSE
16283
22.INSTALL NO. 6 WATER BY-PASS HOSE
16261
23.INSTALL WATER BY-PASS HOSE
12581A
24.INSTALL NO. 1 CYLINDER BLOCK INSULATOR
19850
25.INSTALL GLOW PLUG ASSEMBLY
Using a 10 mm deep socket wrench, install the 4 glow plug assemblies.
Install the No. 1 glow plug connector with the 4 nuts.
Install the 4 glow plug screw grommets.
17111
26.INSTALL INTAKE MANIFOLD
17112
27.INSTALL NO. 2 INTAKE MANIFOLD
12631A
28.INSTALL ENGINE COVER BRACKET
17696
29.INSTALL GAS FILTER BRACKET
23265
30.INSTALL NO. 1 GAS FILTER
89421C
31.INSTALL DIESEL TURBO PRESSURE SENSOR
17853B
32.INSTALL INTAKE MANIFOLD INSULATOR
23810A
33.INSTALL COMMON RAIL ASSEMBLY
23282D
34.INSTALL NO. 4 FUEL HOSE
35.INSTALL INJECTION PIPE SUB-ASSEMBLY
23804C
36.INSTALL FUEL INLET PIPE SUB-ASSEMBLY
11452
37.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
25800
38.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY
25602
39.INSTALL NO. 2 EGR PIPE SUB-ASSEMBLY
25625
40.INSTALL EGR VALVE BRACKET
16296
41.CONNECT NO. 8 WATER BY-PASS HOSE
16295
42.INSTALL NO. 7 WATER BY-PASS HOSE
26100
43.INSTALL DIESEL THROTTLE BODY ASSEMBLY
29300
44.INSTALL VACUUM PUMP ASSEMBLY
16620
45.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
12315A
46.INSTALL ENGINE MOUNTING BRACKET
16288
47.INSTALL NO. 4 WATER BY-PASS PIPE
16603
48.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
16649B
49.INSTALL IDLER PULLEY COVER PLATE
16604
50.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
27020
51.INSTALL GENERATOR ASSEMBLY
88433A
52.INSTALL COMPRESSOR STAY
Install the compressor stay to the cylinder block sub-assembly.
88320
53.INSTALL COOLER COMPRESSOR ASSEMBLY WITH PULLEY
16361A
54.INSTALL FAN AND GENERATOR V BELT
55.CONNECT ENGINE WIRE