Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2013.11–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0050193 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Short in CAN Bus Lines  


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Symptom Trouble Area

*1: w/ Blind Spot Monitor System

*2: w/ Stop and Start System

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: w/ Navigation System

*5: for 4WD/AWD

*6: w/ Entry and Start System

*7: w/ Lane Departure Alert System

The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
·

Short between CAN bus lines

·

ECM

·

Blind spot monitor sensor LH*1

·

Brake actuator assembly (skid control ECU)

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)

·

Air conditioning amplifier assembly

·

Engine stop and start ECU*2

·

Radio and display receiver assembly*3

·

Navigation receiver assembly*4

·

4WD ECU assembly*5

·

Certification ECU (smart key ECU assembly)*6

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Airbag sensor assembly

·

Lane departure warning camera*7

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

No. 3 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C279372E02
6.219,1.469 6.677,1.667 0.458,0.198 10 false ECM 6.01,1.177 6.469,1.375 0.458,0.198 10 false CANL 6.01,0.417 6.469,0.615 0.458,0.198 10 false CANH 5.135,0.531 5.594,0.729 0.458,0.198 10 false A62 5.135,1.063 5.594,1.26 0.458,0.198 10 false A62 5.594,0.531 6.052,0.729 0.458,0.198 10 false A61 5.583,1.052 6.042,1.25 0.458,0.198 10 false A61 5.604,0.813 6.063,1.01 0.458,0.198 10 false 6*2 5.604,0.271 6.063,0.469 0.458,0.198 10 false 7*2 5.146,0.271 5.604,0.469 0.458,0.198 10 false 13*1 5.146,0.813 5.604,1.01 0.458,0.198 10 false 26*1 3.906,1.063 4.365,1.26 0.458,0.198 10 false N27 3.896,0.531 4.354,0.729 0.458,0.198 10 false N27 3.958,0.292 4.417,0.49 0.458,0.198 10 false 1 3.958,0.823 4.417,1.021 0.458,0.198 10 false 2 3.969,2.396 4.427,2.594 0.458,0.198 10 false 2 3.969,1.875 4.427,2.073 0.458,0.198 10 false 1 3.885,2.115 4.344,2.313 0.458,0.198 10 false N28 3.896,2.646 4.354,2.844 0.458,0.198 10 false N28 2.75,1.052 3.208,1.25 0.458,0.198 10 false N29 2.833,0.802 3.292,1 0.458,0.198 10 false 2 2.833,0.292 3.292,0.49 0.458,0.198 10 false 1 2.75,0.521 3.208,0.719 0.458,0.198 10 false N29 1.25,0.417 1.708,0.615 0.458,0.198 10 false 2 1.25,0.938 1.708,1.135 0.458,0.198 10 false 7 0.75,0.542 1.208,0.74 0.458,0.198 10 false CA1P 0.75,1.042 1.208,1.24 0.458,0.198 10 false CA1N 0.188,1.427 0.646,1.625 0.458,0.198 10 false R1 0.198,1.594 2.25,1.833 2.052,0.24 10 false Blind Spot Monitor Sensor LH*3 2.531,3.063 4.458,3.5 1.927,0.438 10 false No. 3 CAN Junction Connector 3.594,8.167 6.083,8.417 2.49,0.25 10 false No. 1 CAN Junction Connector 6.031,6.125 6.49,6.323 0.458,0.198 10 false CANH 6.031,6.646 6.49,6.844 0.458,0.198 10 false CANL 2.823,3.771 3.281,3.969 0.458,0.198 10 false 1 3.969,3.75 4.427,3.948 0.458,0.198 10 false 1 3.969,5.875 4.427,6.073 0.458,0.198 10 false 1 2.823,5.875 3.281,6.073 0.458,0.198 10 false 1 3.979,4.292 4.438,4.49 0.458,0.198 10 false 2 2.833,4.292 3.292,4.49 0.458,0.198 10 false 2 2.833,6.396 3.292,6.594 0.458,0.198 10 false 2 3.979,6.396 4.438,6.594 0.458,0.198 10 false 2 5.74,6 6.198,6.198 0.458,0.198 10 false 14 5.74,6.521 6.198,6.719 0.458,0.198 10 false 13 3.854,4 4.313,4.198 0.458,0.198 10 false G118 3.854,4.521 4.313,4.719 0.458,0.198 10 false G118 2.708,4 3.167,4.198 0.458,0.198 10 false G120 2.708,4.521 3.167,4.719 0.458,0.198 10 false G120 1.25,3.896 1.708,4.094 0.458,0.198 10 false 25 1.25,4.427 1.708,4.625 0.458,0.198 10 false 14 0.74,3.99 1.198,4.188 0.458,0.198 10 false CANH 0.75,4.531 1.208,4.729 0.458,0.198 10 false CANL 3.865,6.115 4.323,6.313 0.458,0.198 10 false G123 3.854,6.646 4.313,6.844 0.458,0.198 10 false G123 2.708,6.115 3.167,6.313 0.458,0.198 10 false G124 2.698,6.635 3.156,6.833 0.458,0.198 10 false G124 0.188,4.896 2.24,5.135 2.052,0.24 10 false A64 0.188,5.063 1.813,5.438 1.625,0.375 10 false Brake Actuator Assembly (Skid Control ECU) 0.469,7.031 2.521,7.271 2.052,0.24 10 false G14 0.49,7.188 1.031,7.417 0.542,0.229 10 false DLC3 0.76,6.115 1.219,6.313 0.458,0.198 10 false CANH 0.771,6.625 1.229,6.823 0.458,0.198 10 false CANL 1.25,6.021 1.708,6.219 0.458,0.198 10 false 6 1.26,6.531 1.719,6.729 0.458,0.198 10 false 14 5.375,7.01 6.594,7.167 1.219,0.156 10 false G78 5.375,7.188 7.052,7.552 1.677,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.167,7.875 2.583,8.333 2.417,0.458 10 false *1: for 2AR-FE, 3ZR-FAE, 3ZR-FE 0.167,8.167 3.417,8.417 3.25,0.25 10 false *2: for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF 0.167,8.5 3.417,8.75 3.25,0.25 10 false *3: w/ Blind Spot Monitor System

C281177E02
3.813,1.24 4.427,1.438 0.615,0.198 10 false G125 3.823,0.719 4.438,0.917 0.615,0.198 10 false G125 2.677,0.719 3.292,0.917 0.615,0.198 10 false G126 2.667,1.229 3.281,1.427 0.615,0.198 10 false G126 2.667,2.823 3.281,3.021 0.615,0.198 10 false G127 2.667,3.354 3.281,3.552 0.615,0.198 10 false G127 3.823,3.354 4.438,3.552 0.615,0.198 10 false G119 3.823,2.833 4.438,3.031 0.615,0.198 10 false G119 1.26,1.229 1.875,1.427 0.615,0.198 10 false G81 1.719,1.229 2.333,1.427 0.615,0.198 10 false G80 1.708,0.719 2.323,0.917 0.615,0.198 10 false G80 1.271,0.719 1.885,0.917 0.615,0.198 10 false G81 0.688,0.729 1.302,0.927 0.615,0.198 10 false CANH 6.01,0.719 6.625,0.917 0.615,0.198 10 false CANH 6.01,1.229 6.625,1.427 0.615,0.198 10 false CANL 0.688,1.24 1.302,1.438 0.615,0.198 10 false CANL 0.688,3.375 1.302,3.573 0.615,0.198 10 false CANL 0.677,2.844 1.292,3.042 0.615,0.198 10 false CANH 6.01,6.833 6.625,7.031 0.615,0.198 10 false CANH 6.01,7.375 6.625,7.573 0.615,0.198 10 false CANL 0.667,4.74 1.281,4.938 0.615,0.198 10 false CANH 0.635,6.813 1.25,7.01 0.615,0.198 10 false CANH 0.698,5.24 1.313,5.438 0.615,0.198 10 false CANL 0.656,7.344 1.271,7.542 0.615,0.198 10 false CANL 2.51,3.969 5.063,4.219 2.552,0.25 10 false No. 1 CAN Junction Connector 3.938,8.531 6.49,8.781 2.552,0.25 10 false No. 2 CAN Junction Connector 3.823,4.708 4.438,4.906 0.615,0.198 10 false G129 3.823,5.24 4.438,5.438 0.615,0.198 10 false G129 2.667,4.708 3.281,4.906 0.615,0.198 10 false G155 2.667,5.229 3.281,5.427 0.615,0.198 10 false G155 3.813,6.823 4.427,7.021 0.615,0.198 10 false G156 3.823,7.344 4.438,7.542 0.615,0.198 10 false G156 2.667,6.823 3.281,7.021 0.615,0.198 10 false G130 2.667,7.344 3.281,7.542 0.615,0.198 10 false G130 1.219,7.354 1.833,7.552 0.615,0.198 10 false G143 1.219,6.813 1.833,7.01 0.615,0.198 10 false G143 1.677,6.823 2.292,7.021 0.615,0.198 10 false G139 1.677,7.354 2.292,7.552 0.615,0.198 10 false G139 3.917,0.5 4.531,0.698 0.615,0.198 10 false 1 2.781,0.5 3.396,0.698 0.615,0.198 10 false 1 2.792,2.615 3.406,2.813 0.615,0.198 10 false 1 3.938,2.604 4.552,2.802 0.615,0.198 10 false 1 3.948,4.479 4.563,4.677 0.615,0.198 10 false 1 2.813,4.479 3.427,4.677 0.615,0.198 10 false 1 2.792,6.573 3.406,6.771 0.615,0.198 10 false 1 3.938,6.594 4.552,6.792 0.615,0.198 10 false 1 3.938,7.115 4.552,7.313 0.615,0.198 10 false 2 2.781,7.135 3.396,7.333 0.615,0.198 10 false 2 2.802,4.99 3.417,5.188 0.615,0.198 10 false 2 3.938,5 4.552,5.198 0.615,0.198 10 false 2 3.938,3.146 4.552,3.344 0.615,0.198 10 false 2 2.802,3.125 3.417,3.323 0.615,0.198 10 false 2 2.802,1.01 3.417,1.208 0.615,0.198 10 false 2 3.938,1.031 4.552,1.229 0.615,0.198 10 false 2 5.698,0.625 6.313,0.823 0.615,0.198 10 false 13 5.698,1.135 6.313,1.333 0.615,0.198 10 false 22 1.25,0.479 1.865,0.677 0.615,0.198 10 false 11*4 1.229,1 1.844,1.198 0.615,0.198 10 false 12*4 1.74,1.01 2.354,1.208 0.615,0.198 10 false 9*5 1.74,0.49 2.354,0.688 0.615,0.198 10 false 8*5 1.229,2.719 1.844,2.917 0.615,0.198 10 false 15 1.229,3.25 1.844,3.448 0.615,0.198 10 false 16 1.219,4.594 1.833,4.792 0.615,0.198 10 false 4 1.229,5.135 1.844,5.333 0.615,0.198 10 false 8 5.76,6.719 6.375,6.917 0.615,0.198 10 false 3 5.771,7.25 6.385,7.448 0.615,0.198 10 false 2 0.156,1.625 1.708,2.01 1.552,0.385 10 false Air Conditioning Amplifier Assembly 5.563,1.615 6.938,1.958 1.375,0.344 10 false G92 5.563,1.792 7.115,2.156 1.552,0.365 10 false Airbag Sensor Assembly 0.115,3.75 2.208,4.042 2.094,0.292 10 false G87 0.125,3.917 2.219,4.208 2.094,0.292 10 false Engine Stop and Start ECU*6 0.125,5.615 2.219,5.906 2.094,0.292 10 false h1 0.125,5.781 2.219,6.073 2.094,0.292 10 false Power Steering ECU Assembly 4.573,7.719 6.667,8.01 2.094,0.292 10 false G12 4.583,7.875 7.031,8.26 2.448,0.385 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 0.094,7.771 2.542,8.156 2.448,0.385 10 false Radio and Display Receiver Assembly*7 1.313,6.604 1.927,6.802 0.615,0.198 10 false 9*7 1.229,7.104 1.844,7.302 0.615,0.198 10 false 10*7 1.698,7.104 2.313,7.302 0.615,0.198 10 false 10*8 1.74,6.583 2.354,6.781 0.615,0.198 10 false 9*8 0.083,8.083 2.531,8.469 2.448,0.385 10 false Navigation Receiver Assembly*8 0.135,8.906 3.333,9.25 3.198,0.344 10 false *4: for Automatic Air Conditioning System 0.125,9.219 3.323,9.563 3.198,0.344 10 false *5: for Manual Air Conditioning System 0.146,9.531 3.344,9.875 3.198,0.344 10 false *6: w/ Stop and Start System 2.969,8.938 6.833,9.406 3.865,0.469 10 false *7: w/ Audio and Visual System (for Radio and Display Type) 2.969,9.26 6.167,9.604 3.198,0.344 10 false *8: w/ Navigation System

C277471E05
2.5,3.833 4.417,4.125 1.917,0.292 10 false No. 2 CAN Junction Connector 5.833,3.792 7,4.167 1.167,0.375 10 false G16 5.833,3.958 7,4.333 1.167,0.375 10 false Combination Meter Assembly 5.75,2.792 6.5,3 0.75,0.208 10 false 32 6.042,3.542 6.792,3.75 0.75,0.208 10 false CANL 6.031,2.792 6.781,3 0.75,0.208 10 false CANH 5.75,3.333 6.5,3.542 0.75,0.208 10 false 31 6.031,0.792 6.781,1 0.75,0.208 10 false CANH 6.031,1.313 6.781,1.521 0.75,0.208 10 false CANL 3.885,0.792 5.052,1.167 1.167,0.375 10 false G131 3.885,1.302 5.052,1.677 1.167,0.375 10 false G131 4,0.552 4.75,0.76 0.75,0.208 10 false 1 4,1.073 4.75,1.281 0.75,0.208 10 false 2 2.844,0.542 3.594,0.75 0.75,0.208 10 false 1 2.844,2.667 3.594,2.875 0.75,0.208 10 false 1 3.99,2.667 4.74,2.875 0.75,0.208 10 false 1 2.854,1.073 3.604,1.281 0.75,0.208 10 false 2 2.854,3.188 3.604,3.396 0.75,0.208 10 false 2 4.021,3.188 4.771,3.396 0.75,0.208 10 false 2 2.729,0.792 3.896,1.167 1.167,0.375 10 false G132 2.719,1.313 3.885,1.688 1.167,0.375 10 false G132 3.875,2.896 5.042,3.271 1.167,0.375 10 false G128 3.875,3.417 5.042,3.792 1.167,0.375 10 false G128 2.729,3.417 3.896,3.792 1.167,0.375 10 false G157 2.729,2.906 3.896,3.281 1.167,0.375 10 false G157 0.75,0.823 1.5,1.031 0.75,0.208 10 false CANH 0.771,1.313 1.521,1.521 0.75,0.208 10 false CANL 0.76,3.438 1.51,3.646 0.75,0.208 10 false CA1N 0.729,2.906 1.479,3.115 0.75,0.208 10 false CA1P 1.271,2.771 2.021,2.979 0.75,0.208 10 false 6 1.292,3.302 2.042,3.51 0.75,0.208 10 false 12 1.26,0.667 2.01,0.875 0.75,0.208 10 false 14 1.26,1.188 2.01,1.396 0.75,0.208 10 false 15 5.802,0.677 6.552,0.885 0.75,0.208 10 false 6 5.823,1.188 6.573,1.396 0.75,0.208 10 false 5 5.563,1.708 6.729,2.083 1.167,0.375 10 false G86 5.573,1.875 7.104,2.094 1.531,0.219 10 false 4WD ECU Assembly*9 0.177,4.271 2.094,4.563 1.917,0.292 10 false *9: for 4WD/AWD 0.177,4.521 2.146,4.708 1.969,0.188 10 false *10: w/ Entry and Start System 0.167,3.792 1.333,4.167 1.167,0.375 10 false Q13 0.167,3.958 2.438,4.313 2.271,0.354 10 false Lane Departure Warning Camera*11 0.167,1.677 1.333,2.052 1.167,0.375 10 false G84 0.167,1.844 2,2.219 1.833,0.375 10 false Certification ECU (Smart Key ECU Assembly)*10 2.188,4.292 4.583,4.594 2.396,0.302 10 false *11: w/ Lane Departure Alert System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

For vehicles with an entry and start system:

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
a.
C253362C01
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.323,0.385 2.323,0.385 2.552,0.385 true 1.958,1.469 1.635,1.896 1.635,1.896 1.385,1.896 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.583,0.313 3.052,0.479 0.469,0.167 10 CANH 1.01,1.813 1.479,1.979 0.469,0.167 10 CANL
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G124 No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

2.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

2.CONNECT CONNECTOR
a.

Reconnect wire harness No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR SIDE)
3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR SIDE)
a.
C253362C01
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.323,0.385 2.323,0.385 2.552,0.385 true 1.958,1.469 1.635,1.896 1.635,1.896 1.385,1.896 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.583,0.313 3.052,0.479 0.469,0.167 10 CANH 1.01,1.813 1.479,1.979 0.469,0.167 10 CANL
*a Front view of DLC3


Disconnect the N28 No. 3 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

NG

9.CONNECT CONNECTOR
4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 3 CAN junction connectors.

C278780C06
5.25,2.833 5.417,2.5 5.417,2.5 5.583,2.5 true 5.25,3 5.417,3.25 5.417,3.25 5.583,3.25 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 2.031,2.198 2.344,2.396 0.313,0.198 10 false N29 5.667,2.417 6.167,2.667 0.5,0.25 10 false CANH 5.667,3.167 6.167,3.417 0.5,0.25 10 false CANL 4.25,2.219 4.563,2.417 0.313,0.198 10 false *a 2.021,1.76 2.333,1.958 0.313,0.198 10 false N27
*1 No. 3 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 3 CAN Junction Connector)
- -


Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Blind Spot Monitor System

N27 Y W ECM
N29 R W Blind Spot Monitor Sensor LH*


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/ Blind Spot Monitor System

N27-1 (CANH) - N27-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N29-1 (CANH) - N29-2 (CANL)* Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to ECM CAN main wire) B
NG (to blind spot monitor sensor LH CAN branch wire [w/ Blind Spot Monitor System]) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

5.CONNECT CONNECTOR

C

7.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 3 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
6.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
C277468C01
1.573,0.313 1.99,0.573 0.417,0.26 0.552,2.354 0.969,2.615 0.417,0.26 2.938,0.729 2.74,0.729 2.74,0.729 2.51,1.125 true 2.958,1.375 2.771,1.375 2.771,1.375 2.51,1.219 true 2.74,2.719 2.552,2.719 2.552,2.719 2.094,3.135 true 2.406,2.521 2.219,2.521 2.219,2.521 2,3.135 true 2.073,0.365 2.385,0.521 0.313,0.156 10 *A 1.031,2.396 1.344,2.552 0.313,0.156 10 *B 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 2.979,0.656 3.427,0.833 0.448,0.177 10 CANH 3,1.302 3.427,1.458 0.427,0.156 10 CANL 1.646,0.365 2.26,0.563 0.615,0.198 10 A62 0.625,2.406 1.24,2.604 0.615,0.198 10 A61 2.438,2.448 2.865,2.604 0.427,0.156 10 CANL 2.792,2.656 3.24,2.833 0.448,0.177 10 CANH
*A for 2AR-FE, 3ZR-FAE, 3ZR-FE
*B for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2AR-FE, 3ZR-FAE, 3ZR-FE
Tester Connection Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF
Tester Connection Condition Specified Condition
A61-7 (CANH) - A61-6 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

7.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 3 CAN junction connectors.

Result:
Proceed to
NEXT




NEXT

8.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
8.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.
C268297C01
1.5,0.167 1.833,0.417 0.333,0.25 0.75,0.667 1,0.667 1,0.667 1.5,1.167 true 0.833,1.833 1.083,1.833 1.083,1.833 1.5,1.333 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.417,1.75 1.031,1.948 0.615,0.198 10 CA1N 1.573,0.208 1.885,0.365 0.313,0.156 10 R1 0.333,0.583 0.948,0.781 0.615,0.198 10 CA1P
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-2 (CA1P) - R1-7 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR LH (CA1P, CA1N)

9.CONNECT CONNECTOR
a.

Reconnect wire harness No. 3 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)
10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C253921C03
5.229,2.802 5.438,2.594 5.438,2.594 5.646,2.594 true 5.229,3 5.438,3.271 5.438,3.271 5.646,3.271 true 0.052,0.063 0.365,0.219 0.313,0.156 10 *1 2.01,1.76 2.438,1.917 0.427,0.156 10 G118 4.25,2.208 4.563,2.365 0.313,0.156 10 *a 5.667,2.521 6.094,2.677 0.427,0.156 10 CANH 5.667,3.198 6.094,3.354 0.427,0.156 10 CANL
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
- -


Code Color (CANH Side) Color (CANL Side) Connect to
G118 L W No. 3 CAN Junction Connector


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G118-1 (CANH) - G118-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

11.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect wire harness No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)
12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)
a.
C253362C01
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.323,0.385 2.323,0.385 2.552,0.385 true 1.958,1.469 1.635,1.896 1.635,1.896 1.385,1.896 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.583,0.313 3.052,0.479 0.469,0.167 10 CANH 1.01,1.813 1.479,1.979 0.469,0.167 10 CANL
*a Front view of DLC3


Disconnect the G129 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)

NG

30.CONNECT CONNECTOR
13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connectors.

C253921C31
5.229,2.802 5.438,2.594 5.438,2.594 5.646,2.594 true 5.229,3 5.438,3.271 5.438,3.271 5.646,3.271 true 0.052,0.063 0.365,0.219 0.313,0.156 10 false *1 2.01,1.76 2.438,1.917 0.427,0.156 10 false G155 4.25,2.208 4.563,2.365 0.313,0.156 10 false *a 2.031,1.979 2.458,2.135 0.427,0.156 10 false G156 2.021,2.198 2.448,2.354 0.427,0.156 10 false G128 2.021,2.646 2.448,2.802 0.427,0.156 10 false G130 2.021,2.865 2.448,3.021 0.427,0.156 10 false G131 2.01,3.083 2.438,3.24 0.427,0.156 10 false G132 2.021,3.313 2.448,3.469 0.427,0.156 10 false G157 5.677,2.5 6.104,2.656 0.427,0.156 10 false CANH 5.677,3.177 6.104,3.333 0.427,0.156 10 false CANL
*1 No. 2 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
- -


Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: w/ Navigation System

*3: for 4WD/AWD

*4: w/ Entry and Start System

*5: w/ Lane Departure Alert System

G128 G W Combination Meter Assembly
G130 Y W
·

Radio and Display Receiver Assembly*1

·

Navigation Receiver Assembly*2


G131 L W 4WD ECU Assembly*3
G132 R W Certification ECU (Smart Key ECU Assembly)*4
G155 LG W Power Steering ECU Assembly
G156 P W Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
G157 B W Lane Departure Warning Camera*5


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: w/ Navigation System

*3: for 4WD/AWD

*4: w/ Entry and Start System

*5: w/ Lane Departure Alert System

G128-1 (CANH) - G128-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G130-1 (CANH) - G130-2 (CANL)*1, *2 Cable disconnected from negative (-) battery terminal 200 Ω or higher
G131-1 (CANH) - G131-2 (CANL)*3 Cable disconnected from negative (-) battery terminal 200 Ω or higher
G132-1 (CANH) - G132-2 (CANL)*4 Cable disconnected from negative (-) battery terminal 200 Ω or higher
G155-1 (CANH) - G155-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G156-1 (CANH) - G156-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G157-1 (CANH) - G157-2 (CANL)*5 Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to combination meter assembly CAN main wire) B
NG (to radio and display receiver assembly [w/ Audio and Visual System {for Radio and Display Type}] or navigation ECU receiver assembly [w/ Navigation System] CAN branch wire) C
NG (to 4WD ECU assembly CAN branch wire [for 4WD/AWD]) D
NG (to certification ECU [smart key ECU assembly] CAN branch wire [w/ Entry and Start System]) E
NG (to power steering ECU assembly CAN branch wire) F
NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) G
NG (to lane departure warning camera CAN branch wire [w/ Lane Departure Alert System]) H



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

14.CONNECT CONNECTOR

C

16.CONNECT CONNECTOR

D

20.CONNECT CONNECTOR

E

22.CONNECT CONNECTOR

F

24.CONNECT CONNECTOR

G

26.CONNECT CONNECTOR

H

28.CONNECT CONNECTOR
14.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

15.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
15.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
C221258C08
1.521,0.333 1.927,0.615 0.406,0.281 1.25,2 1.521,2 1.521,2 1.677,1.323 true 1.052,1.781 1.292,1.781 1.292,1.781 1.615,1.302 true 0.073,0.052 0.24,0.24 0.167,0.188 10 *a 0.635,1.688 1.063,1.844 0.427,0.156 10 CANH 0.875,1.906 1.271,2.063 0.396,0.156 10 CANL 1.583,0.375 1.906,0.563 0.323,0.188 10 G16
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-32 (CANH) - G16-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

16.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

17.CHECK VEHICLE TYPE
17.CHECK VEHICLE TYPE
a.

Check for vehicle types.


Result:
Proceed to
w/ Audio and Visual System (for Radio and Display Type)
w/ Navigation System



w/ Audio and Visual System (for Radio and Display Type)

18.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)

w/ Navigation System

19.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)
18.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E140414C05
1.469,0.417 1.969,0.698 0.5,0.281 2.083,1.469 2.25,2 2.25,2 2.5,2 true 1.938,1.469 1.833,2 1.833,2 1.667,2 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 2.552,1.906 3.167,2.104 0.615,0.198 10 CANL 1.24,1.917 1.854,2.115 0.615,0.198 10 CANH 1.542,0.469 2,0.667 0.458,0.198 10 G143
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-9 (CANH) - G143-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

19.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)
a.
E140414C06
1.469,0.417 1.969,0.698 0.5,0.281 2.083,1.469 2.25,2 2.25,2 2.5,2 true 1.938,1.469 1.833,2 1.833,2 1.667,2 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 2.552,1.917 3.167,2.115 0.615,0.198 10 CANL 1.24,1.927 1.854,2.125 0.615,0.198 10 CANH 1.542,0.469 2,0.667 0.458,0.198 10 G139
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G139-9 (CANH) - G139-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)

20.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

21.CHECK FOR SHORT IN CAN BUS WIRES (4WD ECU ASSEMBLY)
21.CHECK FOR SHORT IN CAN BUS WIRES (4WD ECU ASSEMBLY)
a.
C251077C03
0.333,0.958 0.75,1.25 0.417,0.292 2.583,1.5 2.417,1.5 2.417,1.5 2.24,1.24 true 2.51,1.75 2.344,1.75 2.344,1.75 2.177,1.25 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.396,1.021 0.854,1.219 0.458,0.198 10 G86 2.625,1.406 3.083,1.604 0.458,0.198 10 CANL 2.563,1.656 3.021,1.854 0.458,0.198 10 CANH
*a Rear view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G86-6 (CANH) - G86-5 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD ECU ASSEMBLY (CANH, CANL)

22.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

23.CHECK FOR OPEN IN CAN BUS WIRES (CERTIFICATION ECU)
23.CHECK FOR OPEN IN CAN BUS WIRES (CERTIFICATION ECU)
a.
C277454C01
1.385,0.26 1.865,0.563 0.479,0.302 2.083,1.271 2.438,1.938 2.438,1.938 2.646,1.938 true 1.948,1.271 1.729,1.938 1.729,1.938 1.552,1.938 true 0.073,0.052 0.385,0.208 0.313,0.156 10 *a 1.49,0.344 1.802,0.5 0.313,0.156 10 G84 1.135,1.865 1.594,2.021 0.458,0.156 10 CANH 2.677,1.854 3.135,2.01 0.458,0.156 10 CANL
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-14 (CANH) - G84-15 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

24.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

25.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)
25.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)
a.
C268317C01
2.438,1.167 2.844,1.469 0.406,0.302 1.458,1.271 1.26,0.979 1.26,0.979 1.052,0.979 true 1.042,1.781 1.292,1.781 1.292,1.781 1.458,1.427 true 0.063,0.052 0.375,0.208 0.313,0.156 10 *a 2.552,1.24 2.865,1.396 0.313,0.156 10 h1 0.646,0.896 1.146,1.104 0.5,0.208 10 CANH 0.646,1.698 1.146,1.906 0.5,0.208 10 CANL
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h1-4 (CANH) - h1-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

26.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

27.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
27.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
a.
C277459C01
0.354,1.115 0.771,1.365 0.417,0.25 1.083,1.833 1.333,1.833 1.333,1.833 1.51,1.385 true 2.167,1.833 1.917,1.833 1.917,1.833 1.677,1.385 true 0.083,0.052 0.396,0.208 0.313,0.156 10 *a 2.198,1.75 2.677,1.906 0.479,0.156 10 CANH 0.656,1.75 1.135,1.906 0.479,0.156 10 CANL 0.417,1.167 0.896,1.323 0.479,0.156 10 G12
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-3 (CANH) - G12-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

28.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

29.CHECK FOR SHORT IN CAN BUS WIRES (LANE DEPARTURE WARNING CAMERA)
29.CHECK FOR SHORT IN CAN BUS WIRES (LANE DEPARTURE WARNING CAMERA)
a.
C268302C01
0.333,1.208 0.771,1.448 0.438,0.24 2.063,1.229 2.302,0.854 2.302,0.854 2.5,0.854 true 2.083,1.521 2.271,1.802 2.271,1.802 2.469,1.802 true 0.052,0.042 0.365,0.198 0.313,0.156 10 *a 0.406,1.24 0.719,1.396 0.313,0.156 10 Q13 2.521,1.719 3.021,1.896 0.5,0.177 10 CA1N 2.521,0.771 3.021,0.948 0.5,0.177 10 CA1P
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


Disconnect the lane departure warning camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-6 (CA1P) - Q13-12 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO LANE DEPARTURE WARNING CAMERA (CA1P, CA1N)

30.CONNECT CONNECTOR
a.

Reconnect wire harness No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connectors.

C253921C25
5.229,2.802 5.438,2.594 5.438,2.594 5.646,2.594 true 5.229,3 5.438,3.271 5.438,3.271 5.646,3.271 true 0.052,0.063 0.365,0.219 0.313,0.156 10 false *1 2.021,2.198 2.448,2.354 0.427,0.156 10 false G120 4.25,2.208 4.563,2.365 0.313,0.156 10 false *a 5.667,2.521 6.094,2.677 0.427,0.156 10 false CANH 5.667,3.198 6.094,3.354 0.427,0.156 10 false CANL 2.021,2.427 2.448,2.583 0.427,0.156 10 false G126 2.021,2.646 2.448,2.802 0.427,0.156 10 false G127 2.021,2.865 2.448,3.021 0.427,0.156 10 false G123 2.031,3.302 2.458,3.458 0.427,0.156 10 false G125 2.021,1.969 2.448,2.125 0.427,0.156 10 false G119
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
- -


Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Stop and Start System

G119 V W No. 2 CAN Junction Connector
G120 R W Brake Actuator Assembly (Skid Control ECU)
G123 Y W Main Body ECU (Multiplex Network Body ECU)
G125 BR W Airbag Sensor Assembly
G126 G W Air Conditioning Amplifier Assembly
G127 LG W Engine Stop and Start ECU*


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/ Stop and Start System

G119-1 (CANH) - G119-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G120-1 (CANH) - G120-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G123-1 (CANH) - G123-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G125-1 (CANH) - G125-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G126-1 (CANH) - G126-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G127-1 (CANH) - G127-2 (CANL)* Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to brake actuator assembly [skid control ECU] CAN branch wire) B
NG (to main body ECU [multiplex network body ECU] CAN branch wire) C
NG (to airbag sensor assembly CAN branch wire) D
NG (to air conditioning amplifier assembly CAN branch wire) E
NG (to engine stop and start ECU CAN branch wire [w/ Stop and Start System]) F
NG (to No. 2 CAN junction connector CAN main wire) G



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

32.CONNECT CONNECTOR

C

34.CONNECT CONNECTOR

D

36.CONNECT CONNECTOR

E

38.CONNECT CONNECTOR

F

40.CONNECT CONNECTOR

G

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

32.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

33.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
33.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
a.
C234968C30
1.552,0.177 2.01,0.448 0.458,0.271 0.479,0.74 0.677,0.74 0.677,0.74 1.458,1.281 true 0.885,1.927 1.115,1.927 1.115,1.927 1.458,1.365 true 0.083,0.073 0.344,0.229 0.26,0.156 10 *a 0.479,1.844 0.885,2.01 0.406,0.167 10 CANH 0.063,0.667 0.469,0.833 0.406,0.167 10 CANL 1.667,0.229 2.073,0.438 0.406,0.208 10 A64
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-25 (CANH) - A64-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

34.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
35.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
C212975C04
0.344,1.073 0.813,1.333 0.469,0.26 1.167,0.417 1.333,0.417 1.333,0.417 1.604,1.177 true 1.542,1.177 1.083,0.667 1.083,0.667 0.917,0.667 true 0.073,0.052 0.313,0.24 0.24,0.188 10 *a 0.5,0.594 0.927,0.75 0.427,0.156 10 CANH 0.75,0.333 1.156,0.49 0.406,0.156 10 CANL 0.438,1.135 0.771,1.292 0.333,0.156 10 G78
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G78-14 (CANH) - G78-13 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

36.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

37.CHECK FOR OPEN IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY)
37.CHECK FOR OPEN IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY)
a.
C210016C04
0.302,1 0.75,1.302 0.448,0.302 1.99,1.052 2.198,0.448 2.198,0.448 2.333,0.448 true 2.094,1.323 2.271,1.698 2.271,1.698 2.417,1.698 true 0.052,0.063 0.24,0.24 0.188,0.177 10 *a 2.375,0.375 2.813,0.552 0.438,0.177 10 CANH 0.375,1.073 0.656,1.25 0.281,0.177 10 G92 2.458,1.615 2.896,1.792 0.438,0.177 10 CANL
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G92-13 (CANH) - G92-22 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)

38.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

39.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
39.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
C277462C01
2.594,1.948 3.031,2.208 0.438,0.26 0.156,0.313 0.594,0.573 0.438,0.26 0.635,1.969 0.854,1.969 0.854,1.969 1.042,2.354 true 0.646,1.719 0.896,1.719 0.896,1.719 1.156,2.354 true 1.667,0.875 2.073,1.51 2.073,1.51 2.354,1.51 true 1.583,0.896 1.094,1.458 1.094,1.458 0.771,1.458 true 0.667,0.365 0.979,0.521 0.313,0.156 10 *A 3.115,2.01 3.323,2.375 0.208,0.365 10 *B 0.083,0.073 0.396,0.229 0.313,0.156 10 *a 0.24,0.375 0.698,0.573 0.458,0.198 10 G81 2.677,2 3.135,2.198 0.458,0.198 10 G80 2.396,1.427 2.948,1.625 0.552,0.198 10 CANH 0.219,1.635 0.771,1.833 0.552,0.198 10 CANH 0.25,1.896 0.802,2.094 0.552,0.198 10 CANL 0.375,1.375 0.927,1.573 0.552,0.198 10 CANL
*A for Automatic Air Conditioning System
*B for Manual Air Conditioning System
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Air Conditioning System
Tester Connection Condition Specified Condition
G81-11 (CANH) - G81-12 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

for Manual Air Conditioning System
Tester Connection Condition Specified Condition
G80-8 (CANH) - G80-9 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

40.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

41.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
41.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
a.
C251435C06
0.313,0.927 0.677,1.156 0.365,0.229 2.646,1.5 2.406,1.5 2.406,1.5 2.146,1.188 true 2.573,1.698 2.333,1.698 2.333,1.698 2.073,1.198 true 0.354,0.969 0.813,1.167 0.458,0.198 10 G87 0.073,0.094 0.531,0.292 0.458,0.198 10 *a 2.677,1.417 3.135,1.615 0.458,0.198 10 CANH 2.615,1.625 3.073,1.823 0.458,0.198 10 CANL
*a Rear view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-15 (CANH) - G87-16 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ENGINE STOP AND START ECU (CANH, CANL)