For more information on the injector assemblies and common rail system, refer to System Description.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION
The ECM detects combustion deterioration for a specific cylinder.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0301 | Cylinder 1 Misfire Detected | While the engine speed is approximately 1000 rpm, it is detected that the number of misfires of the No. 1 cylinder is equal to or greater than the standard value.
(3 trip detection logic) |
·
No. 1 injector assembly ·
Compression pressure ·
Valve timing ·
EGR valve assembly ·
Fuel with low cetane number used ·
Flywheel ·
ECM |
Comes on | DTC stored |
| P0302 | Cylinder 2 Misfire Detected | While the engine speed is approximately 1000 rpm, it is detected that the number of misfires of the No. 2 cylinder is equal to or greater than the standard value.
(3 trip detection logic) |
·
No. 2 injector assembly ·
Compression pressure ·
Valve timing ·
EGR valve assembly ·
Fuel with low cetane number used ·
Flywheel ·
ECM |
Comes on | DTC stored |
| P0303 | Cylinder 3 Misfire Detected | While the engine speed is approximately 1000 rpm, it is detected that the number of misfires of the No. 3 cylinder is equal to or greater than the standard value.
(3 trip detection logic) |
·
No. 3 injector assembly ·
Compression pressure ·
Valve timing ·
EGR valve assembly ·
Fuel with low cetane number used ·
Flywheel ·
ECM |
Comes on | DTC stored |
| P0304 | Cylinder 4 Misfire Detected | While the engine speed is approximately 1000 rpm, it is detected that the number of misfires of the No. 4 cylinder is equal to or greater than the standard value.
(3 trip detection logic) |
·
No. 4 injector assembly ·
Compression pressure ·
Valve timing ·
EGR valve assembly ·
Fuel with low cetane number used ·
Flywheel ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0301
P0302 P0303 P0304 |
·
Cylinder 1 Quantity Compensation ·
Cylinder 2 Quantity Compensation ·
Cylinder 3 Quantity Compensation ·
Cylinder 4 Quantity Compensation ·
Target Common Rail Pressure ·
Common Rail Pressure |
If DTC P0301, P0302, P0303 or P0304 is stored, the following symptoms may appear:
Rough idle
Poor driveability
After confirming DTC P0301, P0302, P0303 or P0304, check the internal fuel pressure on the GTS by entering the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure.
Refer to DTC P0201.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0201
After replacing the ECM, the new ECM needs registration and initialization.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION
After replacing an injector assembly, the ECM needs registration.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION
After replacing the EGR valve assembly, the ECM needs initialization.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0301, P0302, P0303 or P0304 is output | A |
| P0301, P0302, P0303 or P0304 and other DTCs are output | B |
If any DTCs other than P0301, P0302, P0303 or P0304 are output, troubleshoot those DTCs first.
A
B
Check the wire harness and connector connections.
The wire harness and connectors have been connected securely and there are good connections.
Disconnect the injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I1-2 (#10) - B112-29 (IJ1+) | Always | Below 1 Ω |
| I1-1 (#1) - B112-59 (IJ1-) | Always | Below 1 Ω |
| I2-2 (#20) - B112-28 (IJ2+) | Always | Below 1 Ω |
| I2-1 (#2) - B112-58 (IJ2-) | Always | Below 1 Ω |
| I3-2 (#30) - B112-27 (IJ3+) | Always | Below 1 Ω |
| I3-1 (#3) - B112-57 (IJ3-) | Always | Below 1 Ω |
| I4-2 (#40) - B112-26 (IJ4+) | Always | Below 1 Ω |
| I4-1 (#4) - B112-56 (IJ4-) | Always | Below 1 Ω |
| I1-2 (#10) or B112-29 (IJ1+) - Body ground | Always | 10 kΩ or higher |
| I1-1 (#1) or B112-59 (IJ1-) - Body ground | Always | 10 kΩ or higher |
| I2-2 (#20) or B112-28 (IJ2+) - Body ground | Always | 10 kΩ or higher |
| I2-1 (#2) or B112-58 (IJ2-) - Body ground | Always | 10 kΩ or higher |
| I3-2 (#30) or B112-27 (IJ3+) - Body ground | Always | 10 kΩ or higher |
| I3-1 (#3) or B112-57 (IJ3-) - Body ground | Always | 10 kΩ or higher |
| I4-2 (#40) or B112-26 (IJ4+) - Body ground | Always | 10 kΩ or higher |
| I4-1 (#4) or B112-56 (IJ4-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation condition of the injector.
Injector is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of EGR-Valve / Data List / Target EGR Position and Actual EGR Valve Pos.
| Active Test Display |
|---|
| Actuator Test of EGR-Valve |
| Data List Display |
|---|
| Target EGR Position |
| Actual EGR Valve Pos |
Perform the following steps 1 to 4.
Step 1
Perform Actuator Test of EGR-Valve with control value of 0% (opening ratio in %).
Monitor the difference of the control value and EGR valve Actuator Position value (0 +/- 3%). EGR valve must operate within 1 second.
Step 2
Wait for 2 seconds or more.
Step 3
Perform Actuator Test of EGR-Valve with control value of 94% (opening ratio in %).
Monitor the difference of the control value and EGR valve Actuator Position value (0 +/- 3%). EGR valve must operate within 1 second.
Step 4
Wait for 2 seconds or more.
Perform the above steps 1 to 4 and check that the part operates as specified.
Part operates as specified.
Check the EGR valve for operation malfunctions and whether it is fully closed.
EGR valve is moving correctly and fully closed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the cylinder compression pressure.
Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel quality.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the engine mounting insulator for deformation.
Engine mounting insulator is not deformation.
There are discernible vibrations when the engine is running.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the flywheel for deformation and deviation.
Flywheel is not deformation and not deviation.
There are discernible vibrations when the engine is running.
If there are no malfunctions up to this step, DTCs may be stored due to vehicle vibrations. Clear the DTCs once and perform a drive test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the flywheel assembly.
Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Replace the engine mounting insulator.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Replace the EGR valve assembly.
Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR VALVE>REMOVAL
Perform EGR learning value reset.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector assembly.
Click hereEngine / Hybrid System>2WW FUEL>FUEL INJECTOR>REMOVAL
Register the injector assembly compensation code.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT