| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B150819 | Turn Signal/Hazard Flasher Circuit Current Above Threshold | Diagnosis Condition:
Auxiliary battery voltage is 10 V or more Malfunction Status:
·
Short in front turn signal light circuit ·
Short in side turn signal light circuit ·
Short in rear turn signal light circuit |
·
Headlight unit assembly ·
Headlight ECU sub-assembly ·
Side turn signal light assembly ·
Outer rear view mirror assembly (w/ Power Retract Mirror with Foot Light) ·
Outer mirror retractor (w/ Power Retract Mirror without Foot Light) ·
Rear combination light socket and wire ·
Combination meter assembly ·
Harness or connector ·
Instrument panel junction block assembly ·
Front turn signal light socket |
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the bulbs before performing the following procedure.
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION
Inspect the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| Front turn signal light LH and side turn signal light LH do not blink. | A |
| Front turn signal light RH and side turn signal light RH do not blink. | B |
| Rear turn signal light LH does not blink. | C |
| Rear turn signal light RH does not blink. | D |
A
B
C
D
Disconnect the G19 combination meter assembly connector.
Disconnect the 4A instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-1 (LL) or 4A-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4F instrument panel junction block assembly connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the 4H*1 or 4N*2 instrument panel junction block assembly connector.
*1: except LHD, Manual Transaxle
*2: for LHD, Manual Transaxle
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the G19 combination meter assembly connector.
Disconnect the A11 headlight ECU sub-assembly LH connector.
Disconnect the J13*1 or J14*2 outer rear view mirror assembly LH connector.
*1: w/ Panoramic View Monitor System
*2: w/o Panoramic View Monitor System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-1 (LL) or A11-11 (TNS) or J13-1 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-1 (LL) or A11-11 (TNS) or J14-10 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the A11 headlight ECU sub-assembly LH connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the J13*1 or J14*2 outer rear view mirror assembly LH connector.
*1: w/ Panoramic View Monitor System
*2: w/o Panoramic View Monitor System
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Remove the headlight unit assembly LH.
for Single Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>REMOVAL
for Triple Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>REMOVAL
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Remove the side turn signal light assembly LH connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. (w/ Power Retract Mirror with Foot Light) | A |
| DTC B150819 is output. (w/ Power Retract Mirror without Foot Light) | B |
| DTC B150718 is output. | C |
A
B
C
Disconnect the C front side turn signal light socket connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
for Single Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>REMOVAL
for Triple Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>REMOVAL
B
for Single Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>REMOVAL
for Triple Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>REMOVAL
Disconnect the G19 combination meter assembly connector.
Disconnect the 4A instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-2 (LR) or 4A-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4F instrument panel junction block assembly connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the 4H*1 or 4N*2 instrument panel junction block assembly connector.
*1: except LHD, Manual Transaxle
*2: for LHD, Manual Transaxle
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the G19 combination meter assembly connector.
Disconnect the A12 headlight ECU sub-assembly RH connector.
Disconnect the I13*1 or I14*2 outer rear view mirror assembly RH connector.
*1: w/ Panoramic View Monitor System
*2: w/o Panoramic View Monitor System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-2 (LR) or A12-11 (TNS) or I13-1 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-2 (LR) or A12-11 (TNS) or I14-10 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the A12 headlight ECU sub-assembly RH connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the I13*1 or I14*2 outer rear view mirror assembly RH connector.
*1: w/ Panoramic View Monitor System
*2: w/o Panoramic View Monitor System
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Remove the headlight unit assembly RH.
for Single Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>REMOVAL
for Triple Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>REMOVAL
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Remove the side turn signal light assembly RH connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. (w/ Power Retract Mirror with Foot Light) | A |
| DTC B150819 is output. (w/ Power Retract Mirror without Foot Light) | B |
| DTC B150718 is output. | C |
A
B
C
Disconnect the C front side turn signal light socket connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
for Single Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>REMOVAL
for Triple Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>REMOVAL
B
for Single Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>REMOVAL
for Triple Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>REMOVAL
Disconnect the N18 rear combination light socket and wire LH connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the G19 combination meter assembly connector.
Disconnect the N18 rear combination light socket and wire LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-5 (TRNL) or N18-4 (TRN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M14 rear combination light socket and wire RH connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the G19 combination meter assembly connector.
Disconnect the M14 rear combination light socket and wire RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-6 (TRNR) or M14-4 (TRN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG