Use the same procedure for RHD and LHD vehicles.
The procedure below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure below is for the LH side.
75954A
1.INSTALL REAR INNER BLACK OUT TAPE LH (w/ Black Out Tape)
75988E
2.INSTALL REAR DOOR OUTSIDE STRIPE LH (w/ Black Out Tape)
75978H
3.INSTALL REAR DOOR LOWER OUTSIDE STRIPE LH (w/ Black Out Tape)
4.INSTALL HOLE PLUG
Install the hole plug.
Use the same procedure described for the other side.
67003C
5.INSTALL REAR DOOR PANEL CUSHION
Attach the claw and install the rear door panel cushion.
6.INSTALL SCREW GROMMET
Attach the claw and install the screw grommet.
Use the same procedure described for the other side.
67836H
7.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH (w/ Child Protection Cover)
Install the rear door lock child protection cover LH.
67858B
8.INSTALL REAR DOOR PANEL PROTECTOR LH
75062
9.INSTALL OUTSIDE MOULDING SET LH (for Off Road Package)
75062
10.INSTALL OUTSIDE MOULDING SET LH (except Off Road Package)
75078
11.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH
67874C
12.INSTALL REAR DOOR NO. 5 WEATHERSTRIP LH
Attach the clip and install the rear door No. 5 weatherstrip LH.
75764A
13.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING LH
75766B
14.INSTALL REAR DOOR WINDOW FRAME MOULDING LH (REAR PILLAR SIDE)
75792
15.INSTALL DOOR WINDOW FRAME MOULDING CLIP
Attach the claw to install a new door window frame moulding clip.
67846A
16.INSTALL REAR DOOR FRONT OUTSIDE SEAL LH
75762B
17.INSTALL REAR DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)
67872
18.INSTALL REAR DOOR WEATHERSTRIP LH
Attach the clip and install the rear door weatherstrip LH.
Attach the clip and install the clip.
| *a | Correct |
| *b | Incorrect |
Check that the rear door weatherstrip LH is securely installed to the rail of the rear door upper window frame moulding LH as shown in the illustration.
If the rear door weatherstrip LH is not securely installed, water may leak into the vehicle.
68640A
19.INSTALL REAR DOOR CHECK ASSEMBLY LH
When reusing a bolt (B):
Clean the threads of the bolt with non-residue solvent.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
Install the rear door check assembly LH to the door panel with the 2 bolts (A).
|
Bolt (A) |
|
Bolt (B) |
Install the rear door check assembly LH to the body panel with the bolt (B).
69204A
20.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly LH.
| *a | Inside |
| *b | Outside |
Attach the guide as shown in the illustration.
Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly LH with the "TORX" screw.
69242G
21.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD
Attach the guide and install the rear door rear outside handle pad.
69241G
22.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD
Attach the claw and guide to install the rear door front outside handle pad.
69227L
23.INSTALL REAR DOOR OUTSIDE HANDLE COVER LH
|
Install in this Direction |
Attach the claw and install the rear door outside handle cover LH as shown in the illustration.
Using a T30 "TORX" socket wrench, install the rear door outside handle cover LH with the "TORX" screw.
69240
24.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
|
Install in this Direction |
Install the rear door outside handle assembly LH by pushing and sliding it in the direction indicated by the arrow shown in the illustration.
| *1 | Holder |
|
Install in this Direction |
Attach the holder as shown in the illustration.
w/ Entry and Start System:
Connect the connector.
|
Install in this Direction |
Attach the claw and close the connector cover as shown in the illustration.
69780E
25.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
69740E
26.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
69038A
27.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)
69318D
28.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)
When reusing rear door lock with motor assembly LH:
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSTALLATION
69060A
29.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)
69780E
30.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
69740E
31.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
69318D
32.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)
When reusing rear door lock with motor assembly LH:
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSTALLATION
69060A
33.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)
85720D
34.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
69804
35.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Apply MP grease to the sliding parts of the rear door window regulator sub-assembly LH.
|
Install in this Direction |
Pull in the rear door window regulator sub-assembly LH through the service hole as shown in the illustration.
|
Nut |
|
Connector |
Install the rear door window regulator sub-assembly LH with the 6 nuts in the order shown in the illustration.
Do not damage the rear door panel with the rear door window regulator sub-assembly LH.
Connect the connector.
68104
36.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
Connect the power window regulator switch assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal.
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25A-FKS:
for M20A-FKS:
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION
Turn the ignition switch to ON.
Move the rear door window regulator sub-assembly LH until the installation bolts can be seen.
|
Install in this Direction |
Insert the rear door glass sub-assembly LH to the rear door panel in the shown in the illustration.
Install the rear door glass sub-assembly LH with the 2 bolts.
Be careful not to damage the rear door glass sub-assembly LH.
Move the rear door window regulator sub-assembly LH until the open position.
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25A-FKS:
for M20A-FKS:
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
Disconnect the power window regulator switch assembly connector.
Install the hole plug.
68189
37.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
Install the rear door quarter window weatherstrip LH to the rear door quarter window glass LH.
68124C
38.INSTALL REAR DOOR QUARTER WINDOW GLASS LH
|
Install in this Direction |
Install the rear door quarter window glass LH with rear door quarter window weatherstrip LH as shown in the illustration.
67408E
39.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
|
Install in this Direction |
Install the rear door glass run LH to the rear door window division bar sub-assembly LH.
|
Install in this Direction |
Insert the rear door window division bar sub-assembly LH with rear door glass run LH into the rear door panel assembly in the direction indicated by the arrow shown in the illustration.
Install the rear door window division bar sub-assembly LH with the 2 bolts.
|
Pull back in this Direction |
Pull back part of the rear door weatherstrip LH and install the screw as shown in the illustration.
68152C
40.INSTALL REAR DOOR GLASS RUN LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Install the rear door glass run LH as shown in the illustration.
Install the rear door glass run LH so that the top of it aligns with the top of the rear door window division bar sub-assembly.
75722A
41.INSTALL REAR DOOR BELT MOULDING LH
67674A
42.INSTALL REAR DOOR FRAME GARNISH LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Attach the guide and install the rear door frame garnish LH in the direction indicated by the arrows, in the order shown in the illustration.
67842E
43.INSTALL REAR DOOR SERVICE HOLE COVER LH
| *a | Reference Point |
|
Butyl Tape |
Apply new butyl tape to the rear door panel.
Begin applying the butyl tape from the reference point shown in the illustration.
The butyl tape can be applied from either reference point.
| *1 | Rear Door Lock Remote Control Cable Assembly |
| *2 | Rear Door Inside Locking Cable Assembly |
|
Install in this Direction |
Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover LH.
| *a | Reference Point |
|
Butyl Tape |
Align the top of the rear door service hole cover LH with the reference point on the rear door panel and install it.
Align the bottom of the rear door service hole cover LH with the reference point on the rear door panel and install it.
Securely install the rear door service hole cover LH to prevent wrinkles and air bubbles.
There should be no wrinkles or folds after installing the rear door service hole cover LH.
After installing the rear door service hole cover LH, check the seal quality.
86160B
44.INSTALL REAR SPEAKER ASSEMBLY
68199
45.INSTALL REAR DOOR REAR BELT SEAL LH
|
Install in this Direction |
Install the rear door rear belt seal LH as shown in the illustration.
|
Install in this Direction |
Attach the guide and install part of the rear door weatherstrip LH with the clip.
68197A
46.INSTALL REAR DOOR FRONT BELT SEAL LH
|
Install in this Direction |
Install the rear door front belt seal LH to the rear door inner glass weatherstrip LH as shown in the illustration.
68174A
47.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH
|
Install in this Direction |
Install the rear door inner glass weatherstrip LH with rear door front belt seal LH as shown in the illustration.
|
Install in this Direction |
Attach the guide and install part of the rear door weatherstrip LH with the clip.
69206C
48.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH
|
Install in this Direction |
Temporarily install the rear door inside handle sub-assembly LH in the direction indicated by the arrow as shown in the illustration.
Attach the claw and clamp to install the rear door inside handle sub-assembly LH.
67604
49.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
|
Install in this Direction |
Attach the clamp and connect the rear door inside locking cable assembly and rear door lock remote control cable assembly to the rear door inside handle sub-assembly LH in the direction of the arrow indicated in the illustration.
|
Install in this Direction |
Attach the claw and clip to install the rear door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration.
Attach the claw and clip as shown in the illustration.
|
Install in this Direction |
Attach the clip and install the 3 screws as shown in the illustration.
Remove the protective tape.
84810D
50.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
84751R
51.INSTALL REAR SEAT HEATER SWITCH (w/ Seat Heater Switch)
52.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
w/ Seat Heater Switch:
Connect the 2 connectors.
w/o Seat Heater Switch:
Connect the connector.
|
Install in this Direction |
Attach the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the guide and claw to install the rear power window regulator switch assembly with rear door armrest base panel.
Remove the protective tape.
74646A
53.INSTALL DOOR ASSIST GRIP COVER LH
|
Install in this Direction |
Attach the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the claw in the order shown in the illustration.
Attach the clip and install the door assist grip cover LH.
Remove the protective tape.
69278C
54.INSTALL REAR DOOR INSIDE HANDLE BEZEL LH
Attach the claw and install the rear door inside handle bezel LH.
55.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25A-FKS:
for M20A-FKS:
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65351A
56.INSTALL BATTERY HOLE COVER (for HV Model)
58416K
57.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)
58410B
58.INSTALL DECK BOARD ASSEMBLY (for HV Model)
59. INITIALIZE POWER WINDOW CONTROL SYSTEM
60. CHECK POWER WINDOW CONTROL SYSTEM
61. CHECK POWER DOOR LOCK CONTROL SYSTEM