Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › from 2020.08
RM3620E _51 Engine / Hybrid System _076500 M20A-FKS ENGINE MECHANICAL _0372435 CYLINDER HEAD GASKET A

M20A-FKS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Vehicle Identification Number (VIN) registration DTC P063051 is output (Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart entry and start system (for Entry Function)

·

smart entry and start system (for Start Function)

·

Steering lock function


for K120, K120F:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for K120:(Click here)
for K120F:(Click here)

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Front exhaust pipe assembly*2 GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Replacement of continuously variable transaxle assembly
for K120, K120F:
·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for K120:(Click here)
for K120F:(Click here)
Replacement of CVT fluid Air bleed oil pump with motor assembly Stop and start system (Click here)
ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for K120:(Click here)
for K120F:(Click here)
Replacement of front bumper assembly
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Front television camera view adjustment Panoramic view monitor system (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 16620D 3.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16207 4.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16260 5.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

Hide 16278B 6.REMOVE WATER HOSE CLAMP BRACKET

Hide 89481B 7.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ GPF)

Hide 25760 8.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY (w/ GPF)

Hide 25706 9.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ GPF)

Hide 17167 10.SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 22030 13.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25680 14.REMOVE EGR COOLER ASSEMBLY

Hide 25601 15.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25620 16.REMOVE EGR VALVE ASSEMBLY

Hide 16279 17.REMOVE NO. 3 WATER BY-PASS PIPE

Hide 17138B 18.REMOVE INTAKE MANIFOLD STAY

Hide 23826 19.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

Hide 17177 21.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23910A 22.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 23.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 24.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16260 25.REMOVE WATER BY-PASS HOSE ASSEMBLY

Hide 23807 26.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23291 28.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 30.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 32.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 19500 34.REMOVE IGNITION COIL ASSEMBLY

Hide 11452D 35.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15250 37.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 38.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 39.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 40.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 41.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 29300 42.REMOVE VACUUM PUMP ASSEMBLY

Hide 13471 43.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 16305E 45.REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY

Hide 11201 46.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 47.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 48.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320B 49.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 50.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 51.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13507A 52.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

Hide 13050 53.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 55.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 56.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 57.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 58.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 59.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 23477 60.REMOVE FUEL PUMP LIFTER GUIDE

Hide 11103 61.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13501A 63.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

Hide 13502B 64.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

Hide 13801 65.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 66.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 67.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 68.REMOVE CYLINDER HEAD GASKET

A426101

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 69.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 70.INSPECT CYLINDER HEAD SUB-ASSEMBLY