Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE
RM27L0U _54 Brake _049325 PARKING BRAKE _0235756 PARKING BRAKE CABLE A

PARKING BRAKE  PARKING BRAKE CABLE  INSTALLATION  


PROCEDURE

Hide 1.INSTALL PARKING BRAKE SHOE LEVER LH

Hide 2.INSTALL PARKING BRAKE SHOE LEVER RH

HINT:

Use the same procedure for both sides.


Hide 46590 3.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

Hide 46550 4.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY RH

HINT:

Use the same procedure for both sides.


Hide 46580 5.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

Hide 46540 6.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY RH

HINT:

Use the same procedure for both sides.


Hide 7.INSTALL PARKING BRAKE SHOE RETURN SPRING LH

Hide 8.INSTALL PARKING BRAKE SHOE RETURN SPRING RH

HINT:

Use the same procedure for both sides.


Hide 9.CHECK PARKING BRAKE INSTALLATION

Hide 42431 10.INSTALL REAR DISC LH

Hide 42431 11.INSTALL REAR DISC RH

HINT:

Use the same procedure for both sides.


Hide 46430 12.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

C181308E01
2.227,0.431 2.369,0.583 0.142,0.152 10 A 2.833,0.589 2.979,0.737 0.145,0.149 10 B 2.971,1.289 3.111,1.445 0.140,0.156 10 C 0.651,1.53 0.782,1.692 0.131,0.163 10 D 1.81,1.031 2.089,0.51 false 1.81,1.179 2.69,0.662 false 1.954,1.373 2.951,1.373 false 1.762,1.375 0.788,1.601 false 2.21,0.51 2.088,0.51 false 2.807,0.662 2.685,0.662 false

a.

Attach the inner cable end to the carrier assembly and tighten the bolt to the specified torque. The inner cable end will be in position A.


b.

Push the inner cable from the opposite end. The inner cable end that is inside the brake assembly will move inbound as shown in B. From there, it will follow the lever shape and push open the guide spring, as shown in C. Finally, after the inner cable end moves in enough, the guide spring will force the cable end to seat in the final operation location, as shown in D.


c.

After connecting the inner cable end to the brake assembly, push and pull the opposite end of the inner cable 2 or 3 times to confirm that the inner cable end and brake assembly are securely connected.


d.
C154244

Install the No. 3 parking brake cable to the rear axle carrier with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install the No. 3 parking brake cable to the frame with the 4 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not bend and twist the parking brake cable.


C353510


f.

Apply MP grease to the areas where the cable contact the intermediate lever.


g.
C180582

Connect the No. 3 parking brake cable to the intermediate lever.


Hide 46420 13.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

C353511E01
0.958,0.979 1.271,1.177 0.313,0.198 10 false *A 4.375,0.708 4.688,0.906 0.313,0.198 10 false *A 0.979,2.302 1.292,2.5 0.313,0.198 10 false *A 0.646,3.656 0.958,3.854 0.313,0.198 10 false *A

HINT:

The No. 2 parking brake cable bolt locations are symmetric to those of the No. 3 parking brake cable, with the exception of the locations indicated with *A.


a.

Install the No. 2 parking brake cable to the rear axle carrier with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the No. 2 parking brake cable to the frame with the 8 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.

Connect the No. 2 parking brake cable to the intermediate lever.


Hide 46458A 14.INSTALL NO. 2 CABLE RETAINER

a.
C156991

Install the retainer with the bolt.

Torque:
13 N*m (128 kgf*cm, 9 ft.*lbf)


Hide 46301A 15.INSTALL INTERMEDIATE LEVER TENSION SPRING

a.
C156990

Install the tension spring.


Hide 16.ADJUST PARKING BRAKE SHOE CLEARANCE

Hide 17.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

Hide 18.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY RH

HINT:

Use the same procedure for both sides.


Hide 19.INSTALL REAR WHEEL LH

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 20.INSTALL REAR WHEEL RH

HINT:

Use the same procedure for both sides.


Hide 21.CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY

Hide 46410 22.INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY

a.

Install the No. 1 parking brake cable to the inside of the vehicle with the 2 bolts (labeled A).

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Connect the clamp (labeled B) to the No. 1 parking brake cable.


c.

Install the clamp with the nut (labeled C).

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.

Install the No. 1 parking brake cable and cable retainer with the bolt (labeled D).

Torque:
13 N*m (128 kgf*cm, 9 ft.*lbf)


e.

Temporarily install the adjustment nut and lock nut (labeled E).

NOTICE:

Do not bend and twist the parking brake cable.


HINT:

The nuts will be tightened to a torque specification in the "Adjust Parking Brake Pedal Travel" procedure.


C183663E06
1.75,3.573 1.906,3.76 0.156,0.188 10 false A 3.615,4.25 3.76,4.396 0.146,0.146 10 false B 3.188,4.021 3.375,4.208 0.188,0.188 10 false C 2.521,0.5 2.656,0.667 0.135,0.167 10 true D 5.99,1.229 6.188,1.396 0.198,0.167 10 false E 0.594,3.49 0.75,3.677 0.156,0.188 10 false A


Hide 17450B 23.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for 3UR-FE)

Hide 17450B 24.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for 3UR-FBE)

Hide 25.SETTLE PARKING BRAKE SHOE AND DISC

Hide 26.CHECK PARKING BRAKE PEDAL TRAVEL

Hide 27.ADJUST PARKING BRAKE PEDAL TRAVEL

Hide 55046A 29.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH

Hide 53601 30.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 34.INSPECT FOR EXHAUST GAS LEAK