Vehicle may slip off the vehicle hoist if the vehicle hoist is handled incorrectly.
Danger! Life-threatening injuries!
Observe safety information on raising the vehicle using a vehicle hoist.
For additional information see:
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Motor vehicle may slip off the vehicle hoist if the weight is distributed unevenly.
Danger! Life-threatening injuries!
Ensure there is a specific weight compensation on the motor vehicle.
Motor vehicle may slip off the vehicle hoist where components are supported.
Danger! Life-threatening injuries!
Secure the vehicle hoist against lowering and lifting.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>B48 BATTERY>REMOVAL
2.REMOVE AND INSTALL BONNET HOOD SUPPORT ASSEMBLY
12601B
3.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
4.REMOVE NO. 1 INTEGRATION RELAY
5.REMOVE ENGINE ROOM ECM BOX
6.REMOVE WHEEL ASSEMBLY
53826A
7.REMOVE FRONT FENDER UPPER PROTECTOR LH
53825A
8.REMOVE FRONT FENDER UPPER PROTECTOR RH
Use the same procedure as for the LH side.
51219
9.REMOVE FRONT SUSPENSION MEMBER LOWER PROTECTOR
53879
10.REMOVE FRONT FENDER LINER LH
53878
11.REMOVE FRONT FENDER LINER RH
Use the same procedure as for the LH side.
25051
12.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
13.INSTALL ENGINE HANGER
Guide in and position special tool 2 459 012 on cylinder head.
Tighten the bolts (1) of special tool 2 459 012.
14.INSTALL ENGINE SUPPORT BRIDGE
for Type A:
Click hereSuspension>FRONT SUSPENSION>FRONT SUSPENSION MEMBER>REMOVAL
for Type B:
Click hereSuspension>FRONT SUSPENSION>FRONT SUSPENSION MEMBER>REMOVAL
12361
15.SEPARATE FRONT ENGINE MOUNTING INSULATOR LH
Release the E14 bolt (1) from the top.
12361
16.SEPARATE FRONT ENGINE MOUNTING INSULATOR RH
Release the E14 bolt (1) from the top.
52822
17.REMOVE AIR INTAKE DUCT LH
Lift air intake duct LH (1) with the guide (2), detach it from the latch mechanisms (3) to the rear and remove.
52821
18.REMOVE AIR INTAKE DUCT RH
Use the same procedure as for the LH side.
45220
19.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY
82161
20.SEPARATE FLOOR WIRE
Loosen T25 screws (1).
Remove the wire harness mounting (2) with wire harness, move it to the side and secure it in place.
48630
21.REMOVE FRONT UPPER SUSPENSION ARM ASSEMBLY LH (w/ Front Suspension Member Bracket)
Loosen 18 mm bolt (1).
Remove the front suspension member bracket sub-assembly LH (2).
48610
22.REMOVE FRONT UPPER SUSPENSION ARM ASSEMBLY RH (w/ Front Suspension Member Bracket)
Use the same procedure as for the LH side.
51201
23.SEPARATE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
| *a | Engine Lifter |
| *b | Attachment |
|
Attachment placement location |
Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.
The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.
If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments to keep the front suspension crossmember sub-assembly level.
Remove the E11 bolts (1).
Perform the operations on the left and right side.
Remove the E14 bolts (1), E18 bolts (2), bolts (3) and E18 bolts (4)
Lower the front axle support (1) by dimension (A).
Dimension (A) = maximum of 100 mm
When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.
12361
24.REMOVE FRONT ENGINE MOUNTING INSULATOR LH
Loosen bolts (1).
Remove front engine mounting insulator LH (2).
12361
25.REMOVE FRONT ENGINE MOUNTING INSULATOR RH
Use the same procedure as for the LH side.
12315
26.REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH
Loosen E12 bolts (1).
Remove the No. 1 front engine mounting bracket LH (2).
12311
27.REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH
Loosen E12 bolts (1).
Remove the No. 1 front engine mounting bracket RH (2).