Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  P0305  Cylinder 5 Misfire Detected  P0306  Cylinder 6 Misfire Detected  P0307  Cylinder 7 Misfire Detected  P0308  Cylinder 8 Misfire Detected  


DESCRIPTION

A093767E16
2.302,0.906 2.708,1.073 0.406,0.167 10 false ECM 0.427,0.927 1.292,1.125 0.865,0.198 10 false CMP Sensor 0.427,1.729 1.292,1.917 0.865,0.188 10 false CKP Sensor

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.

If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and stores a DTC.

DTC No. DTC Detection Condition Trouble Area
P0300 Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
·

High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks when detect immediately).

·

Emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Injector assembly

·

Fuel pressure

·

Mass Air Flow (MAF) meter

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Air induction system

·

EGR valve assembly

·

ECM


P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
·

High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks when detect immediately).

·

Emission deterioration misfire occurs (MIL illuminates).



When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).

·

Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs once.

·

An excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).

·

At a high engine rpm, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.

·

At a normal engine rpm, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.


HINT:

If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.



MONITOR STRATEGY

Related DTCs P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
P0307: Cylinder 7 misfire
P0308: Cylinder 8 misfire
Required Sensors/Components (Main) Crankshaft position sensor and camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature and intake air temperature sensors and mass air flow meter
Frequency of Operation Continuous
Duration 1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation 2 driving cycles: MIL illuminates when misfire detected
MIL flashes immediately: When catalyst damaged misfire occurs
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Misfire
Monitor runs whenever following DTCs not present P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (Knock Sensor)
P0335 (Crankshaft position sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle speed sensor)
Battery voltage 8 V or more
VVT system Not operated by scan tool
Engine RPM 400 to 5900 rpm
Either of following conditions (a) or (b) met -
(a) ECT at engine start More than -7°C (19°F)
(b) ECT More than 20°C (68°F)
Fuel cut OFF

Monitor Period of Emission-Related-Misfire
First 1000 revolutions after engine start, or Check Mode Crankshaft 1000 revolutions
Except above Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks)
All of following conditions 1, 2, 3 and 4 met Crankshaft 200 revolutions x 3
Except above (MIL blinks immediately) Crankshaft 200 revolutions
1. Driving cycles 1st
2. Check mode OFF
3. Engine RPM Less than 2200 rpm
4. Engine load Less than 70%

TYPICAL MALFUNCTION THRESHOLDS

Monitor Period of Emission-Related-Misfire
Misfire rate 1.5% or more

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks)
Number of misfires per 200 revolutions 144 or more (varies with intake air amount and RPM)

MONITOR RESULT

WIRING DIAGRAM

A164725E02
5.11,0.272 5.391,0.428 0.281,0.156 10 #10 5.11,0.958 5.391,1.114 0.281,0.156 10 #20 5.11,1.645 5.391,1.801 0.281,0.156 10 #30 5.11,2.335 5.391,2.491 0.281,0.156 10 #40 5.11,3.026 5.391,3.182 0.281,0.156 10 #50 5.11,3.716 5.391,3.872 0.281,0.156 10 #60 5.11,4.415 5.391,4.571 0.281,0.156 10 #70 5.11,5.133 5.391,5.289 0.281,0.156 10 #80 5.101,5.734 5.405,5.890 0.304,0.156 10 E01 5.101,6.084 5.405,6.240 0.304,0.156 10 E02 5.845,6.559 6.197,6.715 0.351,0.156 10 ECM 5.845,6.414 6.132,6.584 0.286,0.169 10 D74 4.862,6.071 5.045,6.220 0.184,0.150 10 42 4.862,5.72 5.045,5.870 0.184,0.150 10 43 4.778,5.12 5.045,5.269 0.267,0.149 10 106 4.778,3.712 5.045,3.861 0.267,0.149 10 107 4.865,4.406 5.045,4.558 0.180,0.152 10 83 4.865,3.013 5.045,3.165 0.180,0.152 10 84 4.792,2.326 5.045,2.475 0.253,0.149 10 108 4.862,1.64 5.045,1.789 0.184,0.149 10 85 4.778,0.946 5.045,1.095 0.267,0.149 10 109 4.869,0.26 5.045,0.402 0.177,0.142 10 86 3.784,0.268 3.895,0.421 0.111,0.152 10 2 3.784,0.957 3.895,1.109 0.111,0.152 10 2 3.784,1.645 3.895,1.797 0.111,0.152 10 2 3.784,2.333 3.895,2.485 0.111,0.152 10 2 3.784,3.021 3.895,3.174 0.111,0.152 10 2 3.784,3.71 3.895,3.862 0.111,0.152 10 2 3.784,4.398 3.895,4.550 0.111,0.152 10 2 3.784,5.122 3.895,5.274 0.111,0.152 10 2 4.404,0.273 4.518,0.429 0.114,0.156 10 1 0.532,1.368 0.647,1.524 0.114,0.156 10 1 4.404,0.96 4.518,1.116 0.114,0.156 10 1 4.404,1.646 4.518,1.802 0.114,0.156 10 1 4.404,2.333 4.518,2.489 0.114,0.156 10 1 4.404,3.019 4.518,3.175 0.114,0.156 10 1 4.404,3.706 4.518,3.862 0.114,0.156 10 1 4.404,4.392 4.518,4.548 0.114,0.156 10 1 4.408,5.126 4.522,5.282 0.114,0.156 10 1 3.663,0.569 4.527,0.746 0.864,0.177 10 No. 1 Injector 3.663,0.429 3.937,0.580 0.274,0.151 10 H1 3.663,1.802 3.937,1.953 0.274,0.151 10 H2 3.663,3.185 3.937,3.335 0.274,0.151 10 H3 3.663,4.576 3.937,4.727 0.274,0.151 10 H4 3.663,1.256 4.527,1.433 0.864,0.177 10 No. 2 Injector 3.663,1.116 3.961,1.266 0.298,0.151 10 F1 3.663,2.498 3.961,2.649 0.298,0.151 10 F2 3.663,3.881 3.961,4.031 0.298,0.150 10 F3 3.663,5.3 3.961,5.451 0.298,0.150 10 F4 3.663,1.943 4.527,2.119 0.864,0.177 10 No. 3 Injector 3.663,2.629 4.527,2.806 0.864,0.177 10 No. 4 Injector 3.663,3.323 4.527,3.500 0.864,0.177 10 No. 5 Injector 3.663,4.022 4.527,4.199 0.864,0.177 10 No. 6 Injector 3.663,4.712 4.527,4.889 0.864,0.177 10 No. 7 Injector 3.663,5.432 4.527,5.608 0.864,0.177 10 No. 8 Injector 2.917,0.475 3.170,0.638 0.253,0.163 10 INJ 1.566,0.909 1.847,1.065 0.282,0.156 10 IG2 0.424,0.505 1.086,0.666 0.662,0.161 10 IG2 MAIN 2.34,0.609 2.554,0.779 0.214,0.170 10 1B 2.34,0.343 2.554,0.513 0.214,0.170 10 1B 1.083,1.369 1.297,1.539 0.214,0.170 10 1B 0.266,1.369 0.480,1.539 0.214,0.170 10 1C 2.395,0.201 2.496,0.343 0.100,0.142 10 8 2.395,0.775 2.496,0.917 0.100,0.142 10 7 1.353,1.372 1.484,1.514 0.132,0.142 10 6 1.232,1.743 1.364,1.885 0.132,0.142 10 6 1.232,2.677 1.364,2.819 0.132,0.142 10 5 1.643,1.526 2.771,1.709 1.128,0.184 10 Integration Relay 1.257,1.958 1.534,2.123 0.276,0.165 10 IG2 1.239,2.425 1.571,2.590 0.332,0.165 10 AM2 1.687,2.263 2.648,2.465 0.961,0.202 10 Ignition Switch 1.687,2.116 1.880,2.291 0.193,0.174 10 J9 1.264,3.237 1.596,3.421 0.332,0.184 10 AM2 1.425,5.738 1.900,5.922 0.474,0.184 10 Battery

A259910E03
5.377,0.841 5.713,1.011 0.336,0.170 10 IGT1 3.471,0.911 3.808,1.081 0.336,0.170 10 IGT1 5.377,2.508 5.713,2.678 0.336,0.170 10 IGT3 5.377,4.176 5.713,4.346 0.336,0.170 10 IGT5 5.377,5.843 5.713,6.013 0.336,0.170 10 IGT7 5.378,1.25 5.709,1.419 0.331,0.169 10 IGF1 3.473,1.32 3.804,1.489 0.331,0.169 10 IGF1 5.911,6.458 6.206,6.614 0.295,0.156 10 D74 5.121,0.841 5.305,0.997 0.184,0.156 10 40 5.121,2.508 5.305,2.664 0.184,0.156 10 37 5.121,4.176 5.305,4.332 0.184,0.156 10 35 5.121,5.843 5.305,5.999 0.184,0.156 10 38 5.037,1.25 5.304,1.406 0.267,0.156 10 104 5.902,6.612 6.266,6.796 0.364,0.184 10 ECM 3.853,0.831 3.968,0.987 0.114,0.156 10 3 3.856,1.228 3.991,1.391 0.135,0.163 10 2 2.891,0.835 2.991,0.991 0.100,0.156 10 1 2.897,1.227 3.011,1.383 0.114,0.156 10 4 2.813,1.58 3.107,1.736 0.295,0.156 10 D10 2.841,1.748 4.010,1.918 1.170,0.170 10 No. 1 Ignition Coil 3.051,0.909 3.262,1.063 0.211,0.154 10 +B 3.051,1.316 3.401,1.471 0.350,0.156 10 GND 3.471,2.593 3.808,2.762 0.336,0.170 10 IGT3 3.473,3.001 3.804,3.170 0.331,0.169 10 IGF2 3.853,2.512 3.968,2.668 0.114,0.156 10 3 3.856,2.909 3.991,3.072 0.135,0.163 10 2 2.891,2.502 2.991,2.658 0.100,0.156 10 1 2.897,2.909 3.011,3.065 0.114,0.156 10 4 2.813,3.261 3.107,3.417 0.295,0.156 10 D12 2.841,3.429 4.010,3.599 1.170,0.170 10 No. 3 Ignition Coil 3.051,2.59 3.262,2.744 0.211,0.154 10 +B 3.051,2.997 3.401,3.153 0.350,0.156 10 GND 3.471,4.26 3.808,4.430 0.336,0.170 10 IGT5 3.473,4.669 3.804,4.838 0.331,0.169 10 IGF2 3.853,4.18 3.968,4.335 0.114,0.156 10 3 3.856,4.576 3.991,4.739 0.135,0.163 10 2 2.891,4.184 2.991,4.340 0.100,0.156 10 1 2.897,4.576 3.011,4.732 0.114,0.156 10 4 2.813,4.928 3.107,5.084 0.295,0.156 10 D14 2.841,5.096 4.010,5.266 1.170,0.170 10 No. 5 Ignition Coil 3.051,4.258 3.262,4.411 0.211,0.154 10 +B 3.051,4.664 3.401,4.820 0.350,0.156 10 GND 3.471,5.927 3.808,6.097 0.336,0.170 10 IGT7 3.473,6.336 3.804,6.505 0.331,0.169 10 IGF1 3.853,5.847 3.968,6.003 0.114,0.156 10 3 3.856,6.244 3.991,6.407 0.135,0.163 10 2 2.891,5.837 2.991,5.993 0.100,0.156 10 1 2.897,6.243 3.011,6.399 0.114,0.156 10 4 2.813,6.595 3.107,6.751 0.295,0.156 10 D16 2.813,6.764 3.982,6.933 1.170,0.170 10 No. 7 Ignition Coil 3.051,5.925 3.262,6.079 0.211,0.154 10 +B 3.051,6.331 3.401,6.487 0.350,0.156 10 GND 1.657,0.515 1.905,0.671 0.248,0.156 10 INJ 0.139,0.118 1.119,0.302 0.980,0.184 10 from IG2 Relay 1.54,7.548 1.668,7.718 0.128,0.170 10 A 4.553,7.548 4.681,7.718 0.128,0.170 10 B 4.791,7.548 4.919,7.718 0.128,0.170 10 C

A259911E02
5.38,0.896 5.748,1.061 0.368,0.165 10 IGT2 5.38,2.559 5.748,2.724 0.368,0.165 10 IGT4 5.38,4.221 5.748,4.386 0.368,0.165 10 IGT6 5.38,5.903 5.748,6.068 0.368,0.165 10 IGT8 5.38,1.307 5.730,1.491 0.350,0.184 10 IGF2 5.945,6.661 6.240,6.826 0.295,0.165 10 D74 5.135,0.91 5.347,1.085 0.211,0.174 10 33 5.07,1.307 5.346,1.472 0.276,0.165 10 105 5.144,2.563 5.333,2.724 0.188,0.161 10 34 5.13,4.231 5.319,4.391 0.188,0.161 10 36 5.13,5.912 5.319,6.072 0.188,0.161 10 39 3.853,0.915 3.972,1.071 0.119,0.156 10 3 3.853,1.307 3.972,1.463 0.119,0.156 10 2 2.9,0.915 3.001,1.079 0.100,0.164 10 1 2.886,1.319 3.004,1.493 0.119,0.174 10 4 3.461,0.99 3.820,1.155 0.360,0.165 10 IGT2 3.078,0.999 3.298,1.155 0.221,0.156 10 +B 3.078,1.391 3.419,1.547 0.341,0.156 10 GND 3.451,1.391 3.802,1.547 0.350,0.156 10 IGF2 3.853,2.591 3.972,2.747 0.119,0.156 10 3 3.853,2.984 3.972,3.140 0.119,0.156 10 2 2.9,2.591 3.001,2.755 0.100,0.164 10 1 2.886,2.996 3.004,3.170 0.119,0.174 10 4 3.461,2.666 3.820,2.831 0.360,0.165 10 IGT4 3.078,2.675 3.298,2.831 0.221,0.156 10 +B 3.078,3.068 3.419,3.224 0.341,0.156 10 GND 3.451,3.068 3.802,3.224 0.350,0.156 10 IGF1 3.853,4.254 3.972,4.410 0.119,0.156 10 3 3.853,4.646 3.972,4.802 0.119,0.156 10 2 2.9,4.254 3.001,4.418 0.100,0.164 10 1 2.886,4.658 3.004,4.833 0.119,0.174 10 4 3.461,4.329 3.820,4.494 0.360,0.165 10 IGT6 3.078,4.338 3.298,4.494 0.221,0.156 10 +B 3.078,4.73 3.419,4.886 0.341,0.156 10 GND 3.451,4.73 3.802,4.886 0.350,0.156 10 IGF1 3.853,5.926 3.972,6.082 0.119,0.156 10 3 3.853,6.318 3.972,6.474 0.119,0.156 10 2 2.9,5.926 3.001,6.090 0.100,0.164 10 1 2.886,6.33 3.004,6.505 0.119,0.174 10 4 3.461,6.001 3.820,6.166 0.360,0.165 10 IGT8 3.078,6.01 3.298,6.166 0.221,0.156 10 +B 3.078,6.402 3.419,6.558 0.341,0.156 10 GND 3.451,6.402 3.802,6.558 0.350,0.156 10 IGF2 5.945,6.804 6.286,6.969 0.341,0.165 10 ECM 1.545,0.093 1.684,0.258 0.139,0.165 10 A 4.572,0.093 4.710,0.258 0.139,0.165 10 B 4.796,0.093 4.934,0.258 0.139,0.165 10 C 2.888,1.656 3.202,1.821 0.313,0.165 10 D25 2.888,1.805 4.035,1.989 1.147,0.184 10 No. 2 Ignition Coil 2.888,3.337 3.202,3.502 0.313,0.165 10 D23 2.888,3.487 4.035,3.670 1.147,0.184 10 No. 4 Ignition Coil 2.888,5 3.202,5.165 0.313,0.165 10 D21 2.888,5.149 4.035,5.333 1.147,0.184 10 No. 6 Ignition Coil 2.888,6.662 3.202,6.828 0.313,0.165 10 D19 2.888,6.812 4.035,6.996 1.147,0.184 10 No. 8 Ignition Coil

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

6.

Using the Techstream, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE).

7.

Read the misfire counts of each cylinder (cylinder No. 1 to No. 8) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

8.

Drive the vehicle several times with the conditions, such as engine rpm and engine load, as shown in Misfire RPM and Misfire Load in the freeze frame data.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, with the engine speed and engine load the same as Misfire RPM and Misfire Load in the freeze frame data.

Engine RPM Duration
Idling 8.0 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


9.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.


10.

Record the DTC(s), freeze frame data and misfire counts.

11.

Turn the ignition switch off and wait for at least 5 seconds.

12.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).


CAUTION / NOTICE / HINT

HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors may be a cause of the problem:

1.

The fuel level is low.

2.

Improper fuel is used.

3.

The spark plugs are dirty.


·

After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3, No. 4, No. 5, No. 6, No. 7 and No. 8).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after the repairs.

·

For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine RPM. If misfires only occur during high engine RPM driving, only DTC P0300 is stored.

In the event of DTC P0300 being present, perform the following operations:

2.

Start the engine and conduct the confirmation driving pattern.

3.

Read the misfiring rates of each cylinder or DTC(s) using the Techstream.

4.

Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.

5.

After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.


·

When either Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).

·

When Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.

·

An extremely imbalanced drive wheel, which causes body vibration, may cause misfire DTCs to be detected.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 is output A
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output B


HINT:

If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308 are output, troubleshoot those DTCs first.



A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

OK:

PCV hose is connected correctly and is not damaged.




OK

3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)

NG

3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.


e.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.




NEXT

4.READ VALUE USING TECHSTREAM
4.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.


e.

Read the value displayed on the Techstream.

Result
Data List Techstream Display Proceed to
Catalyst OT MF F/C AVAIL (Avail) A
NOT AVL (Not Avl) B



A

5.PERFORM ACTIVE TEST USING TECHSTREAM

B

6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
5.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.


f.

Perform the Active Test.

NOTICE:

When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.




NEXT

6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count to Cylinder #8 Misfire Count.


b.

Allow the engine to idle.


c.

Read each value for Cylinder #1 Misfire Count to Cylinder #8 Misfire Count displayed on the Techstream. If no misfire counts occur in any cylinders, perform the following procedures:

i.

Move the shift lever to D.


ii.

Check Cylinder #1 Misfire Count to Cylinder #8 Misfire Count.


iii.

If misfire counts are still not displayed, perform procedure "A" and "B", and then check the misfire counts again.

Procedure A: Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read value using Techstream (Misfire RPM and Misfire Load)" procedures above.

Procedure B: Read Cylinder #1 Misfire Count to Cylinder #8 Misfire Count or DTCs displayed on the Techstream.

Result
Result Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B

HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.






A

7.INSPECT SPARK PLUG

B

19.CHECK INTAKE SYSTEM
7.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the spark plug (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

8.CHECK FOR SPARK (SPARK TEST)

NG

8.CHECK FOR SPARK (SPARK TEST)
a.

Perform the spark test (See page Engine / Hybrid System>1UR-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after replacing the ignition coil or the spark plug (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

9.CHECK CYLINDER COMPRESSION PRESSURE
9.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER
U151414E01
0.15,0.993 0.445,1.163 0.295,0.170 10 D74 0.068,0.039 2.416,0.395 2.348,0.356 10 Front view of wire harness connector: (to ECM) 1.883,0.965 2.169,1.120 0.286,0.156 10 E01 3.056,2.533 3.323,2.688 0.267,0.156 10 #10 3.02,1.054 3.287,1.210 0.267,0.156 10 #30 2.48,0.986 2.747,1.142 0.267,0.156 10 #50 2.14,2.895 2.410,3.051 0.271,0.156 10 #60 2.39,2.648 2.675,2.804 0.286,0.156 10 #40 2.785,2.795 3.042,2.951 0.258,0.156 10 #20 3.159,2.51 2.537,1.971 false 2.636,1.158 2.342,1.977 false 3.135,1.231 2.445,1.977 false 2.239,1.725 2.033,1.146 false 2.538,2.098 2.893,2.786 false 2.445,2.098 2.554,2.64 false 2.263,2.889 2.343,2.109 false 1.839,2.655 2.106,2.811 0.267,0.156 10 #80 2.004,2.65 2.235,2.109 false 1.44,2.9 1.707,3.056 0.267,0.156 10 #70 1.625,2.885 2.249,1.952 false

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D74-86 (#10) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-109 (#20) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-85 (#30) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-108 (#40) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-84 (#50) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-107 (#60) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-83 (#70) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-106 (#80) - D74-43 (E01) Ignition switch ON 11 to 14 V




OK

11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>1UR-FE FUEL>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

12.CHECK INTAKE SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

12.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leakage (See page Engine / Hybrid System>1UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage in intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

13.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

13.CHECK FUEL PRESSURE

OK

14.READ VALUE USING TECHSTREAM (COOLANT TEMP)

NG

36.CHECK FUEL LINE
14.READ VALUE USING TECHSTREAM (COOLANT TEMP)

OK

15.READ VALUE USING TECHSTREAM (MAF)

NG

15.READ VALUE USING TECHSTREAM (MAF)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read the MAF with the engine speed at 3000 rpm.

Standard:

Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off)




OK

16.CHECK VALVE TIMING

NG

31.CHECK HARNESS AND CONNECTOR
16.CHECK VALVE TIMING

OK

17.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

NG

17.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

31.CHECK HARNESS AND CONNECTOR

NG

18.INSPECT EGR VALVE ASSEMBLY
18.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

31.CHECK HARNESS AND CONNECTOR

NG

19.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leakage (See page Engine / Hybrid System>1UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage in intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

20.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

20.CHECK FUEL PRESSURE

OK

21.READ VALUE USING TECHSTREAM (COOLANT TEMP)

NG

36.CHECK FUEL LINE
21.READ VALUE USING TECHSTREAM (COOLANT TEMP)

OK

22.READ VALUE USING TECHSTREAM (MAF)

NG

22.READ VALUE USING TECHSTREAM (MAF)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read the MAF with the engine speed at 3000 rpm.

Standard:

Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off)




OK

23.CHECK VALVE TIMING

NG

31.CHECK HARNESS AND CONNECTOR
23.CHECK VALVE TIMING

OK

24.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

NG

24.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

31.CHECK HARNESS AND CONNECTOR

NG

25.INSPECT EGR VALVE ASSEMBLY
25.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

26.INSPECT SPARK PLUG

NG

26.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the spark plug (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

27.CHECK FOR SPARK (SPARK TEST)

NG

27.CHECK FOR SPARK (SPARK TEST)
a.

Perform the spark test (See page Engine / Hybrid System>1UR-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after replacing the ignition coil or the spark plug (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

28.CHECK CYLINDER COMPRESSION PRESSURE
28.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

29.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

29.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
U151414E01
0.15,0.993 0.445,1.163 0.295,0.170 10 D74 0.068,0.039 2.416,0.395 2.348,0.356 10 Front view of wire harness connector: (to ECM) 1.883,0.965 2.169,1.120 0.286,0.156 10 E01 3.056,2.533 3.323,2.688 0.267,0.156 10 #10 3.02,1.054 3.287,1.210 0.267,0.156 10 #30 2.48,0.986 2.747,1.142 0.267,0.156 10 #50 2.14,2.895 2.410,3.051 0.271,0.156 10 #60 2.39,2.648 2.675,2.804 0.286,0.156 10 #40 2.785,2.795 3.042,2.951 0.258,0.156 10 #20 3.159,2.51 2.537,1.971 false 2.636,1.158 2.342,1.977 false 3.135,1.231 2.445,1.977 false 2.239,1.725 2.033,1.146 false 2.538,2.098 2.893,2.786 false 2.445,2.098 2.554,2.64 false 2.263,2.889 2.343,2.109 false 1.839,2.655 2.106,2.811 0.267,0.156 10 #80 2.004,2.65 2.235,2.109 false 1.44,2.9 1.707,3.056 0.267,0.156 10 #70 1.625,2.885 2.249,1.952 false

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D74-86 (#10) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-109 (#20) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-85 (#30) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-108 (#40) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-84 (#50) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-107 (#60) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-83 (#70) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-106 (#80) - D74-43 (E01) Ignition switch ON 11 to 14 V




OK

30.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

30.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>1UR-FE FUEL>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

31.CHECK HARNESS AND CONNECTOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

31.CHECK HARNESS AND CONNECTOR
a.

Check the connection and terminal contact pressure of connectors and wire harness between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

32.CHECK WHETHER DTC OUTPUT RECURS
32.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


k.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL
(DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 is output)
A
NORMAL
(DTC is not output)
B



A

33.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

33.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
U151537E02
1.521,1.531 0.833,1.958 false 1.76,1.521 2.448,1.927 false 1.469,3.865 1.75,4.406 false 1.385,3.865 1.031,4.406 false 0.458,1.396 0.729,1.573 0.271,0.177 10 false D7 0.49,1.875 0.833,2.052 0.344,0.177 10 false E2G 2.5,1.844 2.781,2.083 0.281,0.24 10 false VG 0.125,2.917 0.448,3.094 0.323,0.177 10 false D74 1.667,4.427 2.073,4.625 0.406,0.198 10 false E2G 0.917,4.427 1.135,4.604 0.219,0.177 10 false VG 0.156,0.094 2.49,0.438 2.333,0.344 10 false Front view of wire harness connector: (to MAF Meter) 0.146,2.167 2.479,2.51 2.333,0.344 10 false Front view of wire harness connector: (to ECM)

a.

Disconnect the MAF meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-3 (VG) - D74-74 (VG) Always Below 1 Ω
D7-2 (E2G) - D74-75 (E2G) Always Below 1 Ω
D7-3 (VG) or D74-74 (VG) - Body ground Always 10 kΩ or higher




OK

34.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the results of the inspection performed in steps 15 and 22 indicates no problem, proceed to the next step without replacing the mass air flow meter assembly.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

35.CHECK WHETHER DTC OUTPUT RECURS
35.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


k.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 is output)
B



A

END

B

36.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

REPAIR OR REPLACE FUEL LINE