Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Short in CAN Bus Lines  


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
·

Short between CAN bus lines

·

Combination meter assembly

·

Center airbag sensor assembly

·

Main body ECU (driver side junction block assembly)

·

Steering angle sensor

·

Brake actuator assembly (skid control ECU)

·

Air conditioning amplifier assembly

·

4WD control ECU*1

·

Bus buffer ECU*2

·

Network gateway ECU*3

·

Radio and display receiver assembly*4

·

Navigation receiver assembly*5

·

Brake control with bracket relay*6

·

ECM

·

No. 1 junction connector

·

No. 2 junction connector

·

DLC3 CAN branch wire or connector



*1: for 4WD

*2: w/ Bus Buffer ECU

*3: w/ Blind Spot Monitor System

*4: w/ Audio and Visual System

*5: w/ Navigation System

*6: w/ Trailer Brake Control System


WIRING DIAGRAM

C308789E03
0.719,4.302 1.115,4.479 0.396,0.177 10 false CANH 0.74,4.854 1.125,5.031 0.385,0.177 10 false CANL 0.229,5.229 0.583,5.396 0.354,0.167 10 false J156 0.219,5.406 1.396,5.792 1.177,0.385 10 false Brake Control with Bracket Relay*1 2.969,4.229 3.073,4.365 0.104,0.135 10 false 7 2.896,4.75 3.052,4.927 0.156,0.177 10 false 18 2.958,6.115 3.063,6.271 0.104,0.156 10 false 1 2.896,6.615 3.052,6.792 0.156,0.177 10 false 12 1.229,4.74 1.417,4.896 0.188,0.156 10 false 10 1.24,4.219 1.385,4.375 0.146,0.156 10 false 4 6.01,4.354 6.438,4.531 0.427,0.177 10 false CANH 6.021,4.875 6.406,5.042 0.385,0.167 10 false CANL 5.719,5.177 5.917,5.333 0.198,0.156 10 false J6 5.698,5.354 7.083,5.552 1.385,0.198 10 false Steering Angle Sensor 3.854,4.219 3.948,4.406 0.094,0.188 10 false 6 3.854,4.74 4.021,4.917 0.167,0.177 10 false 17 5.813,4.75 5.896,4.927 0.083,0.177 10 false 9 5.74,4.281 5.917,4.448 0.177,0.167 10 false 10 6.01,6.219 6.427,6.385 0.417,0.167 10 false CANH 6.031,6.729 6.448,6.906 0.417,0.177 10 false CANL 5.51,7.042 5.833,7.198 0.323,0.156 10 false A17 5.5,7.198 7.083,7.51 1.583,0.313 10 false Brake Actuator Assembly (Skid Control ECU) 2.781,7.094 3.042,7.26 0.26,0.167 10 false J75 2.771,7.25 4.344,7.458 1.573,0.208 10 false No. 1 Junction Connector 3.854,6.115 3.958,6.271 0.104,0.156 10 false 8 3.854,6.635 4.042,6.792 0.188,0.156 10 false 19 5.74,6.656 5.917,6.813 0.177,0.156 10 false 13 5.74,6.115 5.917,6.281 0.177,0.167 10 false 12 6.021,2.448 6.417,2.604 0.396,0.156 10 false CANH 6.042,2.865 6.438,3.052 0.396,0.188 10 false CANL 5.906,3.354 6.188,3.521 0.281,0.167 10 false J46 5.906,3.531 7.021,3.948 1.115,0.417 10 false Center Airbag Sensor Assembly 3.854,2.344 3.948,2.51 0.094,0.167 10 false 3 3.854,2.854 4.021,3.031 0.167,0.177 10 false 14 5.75,2.875 5.927,3.052 0.177,0.177 10 false 22 5.729,2.344 5.896,2.51 0.167,0.167 10 false 13 6.042,0.458 6.458,0.635 0.417,0.177 10 false CANH 6.052,1.229 6.448,1.375 0.396,0.146 10 false CANL 5.875,1.49 6.135,1.646 0.26,0.156 10 false J28 5.865,1.656 7.052,2.031 1.188,0.375 10 false Combination Meter Assembly 3.844,0.49 3.948,0.646 0.104,0.156 10 false 4 3.854,0.99 4.031,1.167 0.177,0.177 10 false 15 5.74,1.01 5.917,1.167 0.177,0.156 10 false 40 5.74,0.479 5.917,0.625 0.177,0.146 10 false 39 0.74,2.458 1.156,2.615 0.417,0.156 10 false CANH 0.771,2.99 1.135,3.167 0.365,0.177 10 false CANL 0.229,3.354 0.427,3.521 0.198,0.167 10 false J2 0.198,3.542 1.99,3.958 1.792,0.417 10 false Main Body ECU (Driver Side Junction Block Assembly) 2.948,2.333 3.052,2.5 0.104,0.167 10 false 5 2.896,2.854 3.073,3.031 0.177,0.177 10 false 16 1.25,2.875 1.365,3.052 0.115,0.177 10 false 6 1.25,2.344 1.365,2.5 0.115,0.156 10 false 5 0.719,0.594 1.135,0.75 0.417,0.156 10 false CANH 0.75,1.115 1.146,1.281 0.396,0.167 10 false CANL 0.563,1.479 0.781,1.635 0.219,0.156 10 false J17 0.5,1.646 0.885,1.802 0.385,0.156 10 false DLC3 2.948,0.5 3.052,0.646 0.104,0.146 10 false 2 2.875,0.979 3.052,1.156 0.177,0.177 10 false 13 1.24,1 1.417,1.156 0.177,0.156 10 false 14 1.25,0.469 1.385,0.656 0.135,0.188 10 false 6 0.198,7.219 2.521,7.365 2.323,0.146 10 false *1: w/ Trailer Brake Control System

C288311E02
0.221,5.471 0.633,5.609 0.413,0.139 10 J135 0.221,5.625 1.522,6.039 1.302,0.415 10 Navigation Receiver Assembly*4 0.221,7.343 0.822,7.482 0.601,0.139 10 J123 0.221,7.498 2.135,7.912 1.914,0.415 10 Network Gateway ECU*6 2.981,6.376 3.081,6.515 0.100,0.139 10 6 2.907,6.896 3.080,7.035 0.173,0.139 10 17 0.718,4.586 1.131,4.725 0.413,0.139 10 CANH 0.718,5.106 1.131,5.245 0.413,0.139 10 CANL 1.257,5.026 1.431,5.164 0.173,0.139 10 10 1.257,4.506 1.431,4.644 0.173,0.139 10 9 0.741,6.457 1.131,6.595 0.390,0.139 10 CA1H 0.76,6.977 1.131,7.115 0.371,0.139 10 CA1L 1.257,6.896 1.431,7.035 0.173,0.139 10 15 1.257,6.376 1.431,6.515 0.173,0.139 10 16 6.058,4.586 6.471,4.725 0.413,0.139 10 CAN+ 6.058,5.106 6.471,5.245 0.413,0.139 10 CAN- 5.889,5.471 6.302,5.609 0.413,0.139 10 J59 5.889,5.625 7.024,6.039 1.135,0.415 10 Bus Buffer ECU*5 3.868,4.506 3.968,4.644 0.100,0.139 10 5 3.868,5.026 4.041,5.164 0.173,0.139 10 16 5.827,5.026 5.923,5.164 0.097,0.139 10 2 5.827,4.506 5.923,4.644 0.097,0.139 10 3 6.058,6.38 6.471,6.518 0.413,0.139 10 CANH 6.058,7.096 6.471,7.235 0.413,0.139 10 CANL 6.208,7.348 6.621,7.487 0.413,0.139 10 A24 6.208,7.502 6.636,7.686 0.428,0.183 10 ECM 2.78,7.348 3.193,7.487 0.413,0.139 10 J74 2.78,7.502 4.494,7.917 1.714,0.415 10 No. 2 Junction Connector 3.868,6.397 3.968,6.536 0.100,0.139 10 3 3.868,6.917 4.041,7.056 0.173,0.139 10 14 5.75,6.917 5.923,7.056 0.173,0.139 10 11 5.75,6.397 5.923,6.536 0.173,0.139 10 10 5.806,3.589 6.219,3.727 0.413,0.139 10 A25 5.806,3.743 7.108,4.157 1.302,0.415 10 4WD Control ECU*2 3.868,2.624 3.968,2.762 0.100,0.139 10 2 3.868,3.144 4.041,3.282 0.173,0.139 10 13 5.75,3.144 5.923,3.282 0.173,0.139 10 22 6.058,2.704 6.471,2.843 0.413,0.139 10 CANH 6.058,3.224 6.471,3.363 0.413,0.139 10 CANL 5.75,2.624 5.923,2.762 0.173,0.139 10 23 6.058,0.822 6.471,0.961 0.413,0.139 10 CANH 6.058,1.342 6.471,1.481 0.413,0.139 10 CANL 5.75,0.742 5.923,0.880 0.173,0.139 10 11 5.876,1.706 6.289,1.845 0.413,0.139 10 J19 5.876,1.861 7.081,2.275 1.205,0.415 10 Air Conditioning Amplifier Assembly 3.868,0.742 3.968,0.880 0.100,0.139 10 1 3.868,1.262 4.041,1.400 0.173,0.139 10 12 5.75,1.262 5.923,1.400 0.173,0.139 10 12 0.718,2.709 1.131,2.847 0.413,0.139 10 CANH 0.718,3.229 1.131,3.368 0.413,0.139 10 CANL 0.221,3.593 0.633,3.732 0.413,0.139 10 J139 0.221,3.747 2.015,4.162 1.795,0.415 10 Radio and Display Receiver Assembly*3 2.981,2.628 3.081,2.767 0.100,0.139 10 7 2.907,3.148 3.080,3.287 0.173,0.139 10 18 1.257,3.148 1.431,3.287 0.173,0.139 10 10 1.257,2.628 1.431,2.767 0.173,0.139 10 9 2.981,0.742 3.081,0.880 0.100,0.139 10 4 2.907,1.262 3.080,1.400 0.173,0.139 10 15 0.3,7.965 2.222,8.114 1.922,0.148 10 *2: for 4WD 0.3,8.259 2.854,8.408 2.554,0.148 10 *3: w/ Audio and Visual System 0.3,8.554 2.222,8.702 1.922,0.148 10 *4: w/ Navigation System 2.574,7.965 5.128,8.114 2.554,0.148 10 *5: w/ Bus Buffer ECU 2.574,8.259 5.128,8.408 2.554,0.148 10 *6: w/ Blind Spot Monitor System

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
3.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
a.
U152555E01
0.05,0 0.219,0.185 0.168,0.185 10 *a 2.33,0.273 2.796,0.458 0.466,0.185 10 CANH 1.201,1.758 1.612,1.943 0.410,0.185 10 CANL 1.965,0.847 2.16,0.354 2.16,0.354 2.287,0.354 false 1.97,1.413 1.82,1.839 1.82,1.839 1.688,1.839 false 0.223,1.07 0.474,1.209 0.251,0.139 10 J17

Disconnect the J75 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J17-6 (CANH) - J17-14 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Front view of DLC3



OK

4.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

4.CONNECT CONNECTOR
a.

Reconnect the J75 No. 1 junction connector.



NEXT

5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR)
5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR)
a.
U152555E01
0.05,0 0.219,0.185 0.168,0.185 10 *a 2.33,0.273 2.796,0.458 0.466,0.185 10 CANH 1.201,1.758 1.612,1.943 0.410,0.185 10 CANL 1.965,0.847 2.16,0.354 2.16,0.354 2.287,0.354 false 1.97,1.413 1.82,1.839 1.82,1.839 1.688,1.839 false 0.223,1.07 0.474,1.209 0.251,0.139 10 J17

Disconnect the J74 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J17-6 (CANH) - J17-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3



OK

6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

27.CONNECT CONNECTOR
6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U152537E01
2.266,1.417 2.39,1.663 2.39,1.663 2.572,1.663 false 2.266,1.199 2.453,0.959 2.453,0.959 2.635,0.959 false 0.441,1.236 0.684,1.377 0.243,0.140 10 J74 2.653,0.883 3.114,1.023 0.460,0.140 10 CANH 2.59,1.588 3.051,1.728 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J74-1 (CANH) - J74-12 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NG

13.CONNECT CONNECTOR
7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)
NOTICE:

For vehicles without a 4WD, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Bus Buffer ECU)".


a.
U152538E01
0.441,1.236 0.684,1.377 0.243,0.140 10 J74 2.167,1.417 2.291,1.663 2.291,1.663 2.474,1.663 false 2.167,1.199 2.354,0.959 2.354,0.959 2.537,0.959 false 2.555,0.883 3.015,1.023 0.460,0.140 10 CANH 2.492,1.588 2.952,1.728 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J74-2 (CANH) - J74-13 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)

NG

15.CONNECT CONNECTOR
8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)
NOTICE:

For vehicles without a bus buffer ECU, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Network Gateway ECU)".


a.
U152539E01
0.441,1.236 0.684,1.377 0.243,0.140 10 J74 1.834,1.417 2.278,1.866 2.278,1.866 2.461,1.866 false 1.834,1.199 2.278,0.75 2.278,0.75 2.461,0.75 false 2.479,0.674 2.939,0.814 0.460,0.140 10 CANH 2.479,1.791 2.939,1.931 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J74-5 (CANH) - J74-16 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

17.CONNECT CONNECTOR
9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
NOTICE:

For vehicles without a blind spot monitor system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - ECM)".


a.
U152540E01
1.727,1.417 1.283,1.866 1.283,1.866 1.1,1.866 false 1.727,1.199 1.195,0.662 1.195,0.662 1.012,0.662 false 2.71,1.236 2.953,1.377 0.243,0.140 10 J74 0.491,0.586 0.952,0.726 0.460,0.140 10 CANH 0.579,1.791 1.040,1.931 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J74-6 (CANH) - J74-17 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - ECM)

NG

19.CONNECT CONNECTOR
10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - ECM)
a.
U152541E01
0.441,1.236 0.684,1.377 0.243,0.140 10 J74 2.049,1.417 2.317,1.746 2.317,1.746 2.499,1.746 false 2.049,1.199 2.39,0.87 2.39,0.87 2.572,0.87 false 2.59,0.794 3.051,0.934 0.460,0.140 10 CANH 2.517,1.671 2.977,1.811 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J74-3 (CANH) - J74-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)

Result
Result Proceed to
OK (w/ Audio and Visual System) A
OK (w/ Navigation System) B
NG C



A

11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

C

21.CONNECT CONNECTOR
11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
U152542E01
2.667,1.236 2.910,1.377 0.243,0.140 10 J74 1.611,1.417 1.339,1.823 1.339,1.823 1.157,1.823 false 1.611,1.199 1.232,0.694 1.232,0.694 1.049,0.694 false 0.519,0.618 0.979,0.758 0.460,0.140 10 CANH 0.683,1.748 1.143,1.888 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J74-7 (CANH) - J74-18 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

23.CONNECT CONNECTOR
12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)
a.
U152542E01
2.667,1.236 2.910,1.377 0.243,0.140 10 J74 1.611,1.417 1.339,1.823 1.339,1.823 1.157,1.823 false 1.611,1.199 1.232,0.694 1.232,0.694 1.049,0.694 false 0.519,0.618 0.979,0.758 0.460,0.140 10 CANH 0.683,1.748 1.143,1.888 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J74-7 (CANH) - J74-18 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

25.CONNECT CONNECTOR
13.CONNECT CONNECTOR
a.

Reconnect the J74 No. 2 junction connector.



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
14.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U152458E01
0.363,1.303 0.611,1.445 0.248,0.142 10 J19 0.68,1.842 1.069,1.984 0.390,0.142 10 CANL 2.353,1.842 2.765,1.984 0.413,0.142 10 CANH 0.052,0.046 0.338,0.188 0.286,0.142 10 *a 1.785,1.383 2.237,1.92 2.237,1.92 2.331,1.92 false 1.708,1.383 1.257,1.92 1.257,1.92 1.162,1.92 false

Disconnect the J19 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J19-11 (CANH) - J19-12 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

15.CONNECT CONNECTOR
a.

Reconnect the J74 No. 2 junction connector.



NEXT

16.CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)
16.CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)
a.
U152605E01
0.121,0.065 0.356,0.342 0.235,0.276 10 *a 0.748,1.801 1.140,1.939 0.392,0.137 10 CANL 0.588,1.558 1.003,1.695 0.415,0.137 10 CANH 0.544,1.074 0.811,1.211 0.267,0.137 10 A25 1.452,1.383 1.25,1.632 1.25,1.632 1.095,1.632 false 1.224,1.877 1.39,1.877 1.39,1.877 1.526,1.383 false

Disconnect the A25 4WD control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A25-23 (CANH) - A25-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to 4WD Control ECU)



OK

REPLACE 4WD CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)

17.CONNECT CONNECTOR
a.

Reconnect the J74 No. 2 junction connector.



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRES (BUS BUFFER ECU)
18.CHECK FOR SHORT IN CAN BUS WIRES (BUS BUFFER ECU)
a.
U152607E01
0.878,1.823 1.395,1.965 0.517,0.142 10 CAN- 2.375,1.823 2.892,1.965 0.517,0.142 10 CAN+ 0.119,0.092 0.636,0.234 0.517,0.142 10 *a 0.516,1.084 0.760,1.226 0.244,0.142 10 J59 1.996,1.424 2.15,1.901 2.15,1.901 2.326,1.901 false 1.696,1.424 1.543,1.901 1.543,1.901 1.366,1.901 false

Disconnect the J59 bus buffer ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J59-3 (CAN+) - J59-2 (CAN-) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Bus Buffer ECU)



OK

REPLACE BUS BUFFER ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CAN+, CAN-)

19.CONNECT CONNECTOR
a.

Reconnect the J74 No. 2 junction connector.



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)
20.CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)
a.
U152499E01
1.246,1.243 1.037,1.018 1.037,1.018 0.914,1.018 false 1.031,1.637 1.103,1.637 1.103,1.637 1.355,1.293 false 0.424,0.944 0.813,1.081 0.389,0.137 10 CA1H 0.582,1.551 0.970,1.688 0.389,0.137 10 CA1L 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 2.747,1.159 3.068,1.296 0.321,0.137 10 J123

Disconnect the J123 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J123-16 (CA1H) - J123- 15 (CA1L) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)

21.CONNECT CONNECTOR
a.

Reconnect the J74 No. 2 junction connector.



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
22.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U152461E03
2.885,0.344 2.74,0.344 2.74,0.344 2.479,0.823 true 2.583,0.833 2.792,1.042 2.792,1.042 2.885,1.042 true 0.25,1.073 0.521,1.219 0.271,0.146 10 false A24 0.063,0 0.323,0.146 0.26,0.146 10 false *a 2.917,0.26 3.323,0.406 0.406,0.146 10 false CANH 2.938,0.979 3.344,1.125 0.406,0.146 10 false CANL

Disconnect the A24 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A24-10 (CANH) - A24-11 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)

Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C
NG D



A

B

C

D

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

23.CONNECT CONNECTOR
a.

Reconnect the J74 No. 2 junction connector.



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)
24.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
U152464E01
1.536,0.415 1.860,0.555 0.324,0.140 10 J139 0.047,0.049 0.252,0.218 0.205,0.170 10 *a 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the J139 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J139-9 (CANH) - J139-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

25.CONNECT CONNECTOR
a.

Reconnect the J74 No. 2 junction connector.



NEXT

26.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)
26.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)
a.
U152463E01
0.047,0.049 0.252,0.218 0.205,0.170 10 *a 1.553,0.362 1.877,0.503 0.324,0.140 10 J135 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the J135 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J135-9 (CANH) - J135-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)

27.CONNECT CONNECTOR
a.

Reconnect the J74 No. 2 junction connector.



NEXT

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U152543E01
0.441,1.236 0.684,1.377 0.243,0.140 10 J75 2.266,1.417 2.39,1.663 2.39,1.663 2.572,1.663 false 2.266,1.199 2.453,0.959 2.453,0.959 2.635,0.959 false 2.653,0.883 3.114,1.023 0.460,0.140 10 CANH 2.59,1.588 3.051,1.728 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Disconnect the J75 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J75-1 (CANH) - J75-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)
a.
U152544E01
0.441,1.236 0.684,1.377 0.243,0.140 10 J75 2.049,1.417 2.317,1.746 2.317,1.746 2.499,1.746 false 2.049,1.199 2.39,0.87 2.39,0.87 2.572,0.87 false 2.59,0.794 3.051,0.934 0.460,0.140 10 CANH 2.517,1.671 2.977,1.811 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J75-3 (CANH) - J75-14 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

35.CONNECT CONNECTOR
30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U152545E01
0.441,1.236 0.684,1.377 0.243,0.140 10 J75 1.834,1.417 2.278,1.866 2.278,1.866 2.461,1.866 false 1.834,1.199 2.278,0.75 2.278,0.75 2.461,0.75 false 2.479,0.674 2.939,0.814 0.460,0.140 10 CANH 2.479,1.791 2.939,1.931 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J75-5 (CANH) - J75-16 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NG

37.CONNECT CONNECTOR
31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)
a.
U152546E01
2.701,1.236 2.944,1.377 0.243,0.140 10 J75 1.727,1.417 1.283,1.866 1.283,1.866 1.1,1.866 false 1.727,1.199 1.195,0.662 1.195,0.662 1.012,0.662 false 0.491,0.586 0.952,0.726 0.460,0.140 10 CANH 0.579,1.791 1.040,1.931 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J75-6 (CANH) - J75-17 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - BRAKE CONTROL WITH BRACKET RELAY)

NG

39.CONNECT CONNECTOR
32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - BRAKE CONTROL WITH BRACKET RELAY)
NOTICE:

For vehicles without a trailer brake control system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Skid Control ECU)".


a.
U152549E01
2.753,1.236 2.996,1.377 0.243,0.140 10 J75 1.606,1.417 1.33,1.797 1.33,1.797 1.148,1.797 false 1.606,1.199 1.156,0.67 1.156,0.67 0.974,0.67 false 0.453,0.594 0.913,0.735 0.460,0.140 10 CANH 0.627,1.722 1.087,1.863 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J75-7 (CANH) - J75-18 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)

NG

41.CONNECT CONNECTOR
33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)
a.
U152547E01
2.753,1.236 2.996,1.377 0.243,0.140 10 J75 1.503,1.417 1.227,1.742 1.227,1.742 1.044,1.742 false 1.503,1.199 1.156,0.763 1.156,0.763 0.974,0.763 false 0.453,0.687 0.913,0.827 0.460,0.140 10 CANH 0.524,1.666 0.984,1.807 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J75-8 (CANH) - J75-19 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

43.CONNECT CONNECTOR
34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U152548E01
0.441,1.236 0.684,1.377 0.243,0.140 10 J75 1.937,1.417 2.278,1.866 2.278,1.866 2.461,1.866 false 1.937,1.199 2.278,0.75 2.278,0.75 2.461,0.75 false 2.479,0.674 2.939,0.814 0.460,0.140 10 CANH 2.479,1.791 2.939,1.931 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J75-4 (CANH) - J75-15 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

45.CONNECT CONNECTOR
35.CONNECT CONNECTOR
a.

Reconnect the J75 No. 1 junction connector.



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
36.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
a.
U152453E02
2.01,1 2.479,0.417 2.479,0.417 2.563,0.417 false 2.135,1.25 2.49,1.656 2.49,1.656 2.573,1.656 false 0.427,1.01 0.677,1.156 0.25,0.146 10 false J46 2.615,0.333 3.052,0.51 0.438,0.177 10 false CANH 0.063,0 0.271,0.177 0.208,0.177 10 false *a 2.594,1.583 3,1.76 0.406,0.177 10 false CANL

Disconnect the J46 center airbag sensor assembly connector.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J46-13 (CANH) - J46-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

37.CONNECT CONNECTOR
a.

Reconnect the J75 No. 1 junction connector.



NEXT

38.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
38.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U152508E01
1.53,1.359 1.871,1.926 1.871,1.926 2.01,1.926 false 1.414,1.359 1.073,1.926 1.073,1.926 0.935,1.926 false 2.057,1.853 2.478,1.989 0.422,0.137 10 CANL 0.385,1.853 0.807,1.989 0.422,0.137 10 CANH 0.7,1.161 0.876,1.298 0.176,0.137 10 J2 0.067,0.048 0.267,0.185 0.199,0.137 10 *a

Disconnect the J2 main body ECU (driver side junction block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J2-5 (CANH) - J2-6 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Driver Side Junction Block Assembly])



OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

39.CONNECT CONNECTOR
a.

Reconnect the J75 No. 1 junction connector.



NEXT

40.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
40.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
a.
U152505E01
1.172,1.309 0.944,1.537 0.944,1.537 0.834,1.537 false 1.008,1.802 1.068,1.802 1.068,1.802 1.307,1.309 false 0.338,1.451 0.759,1.594 0.421,0.143 10 CANH 1.688,0.335 1.855,0.478 0.167,0.143 10 J6 0.51,1.72 0.931,1.863 0.421,0.143 10 CANL 0.058,0.035 0.253,0.178 0.195,0.143 10 *a

Disconnect the J6 steering angle sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J6-10 (CANH) - J6-9 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Steering Angle Sensor)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

41.CONNECT CONNECTOR
a.

Reconnect the J75 No. 1 junction connector.



NEXT

42.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE CONTROL WITH BRACKET RELAY)
42.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE CONTROL WITH BRACKET RELAY)
a.
U152659E01
1.526,0.315 1.856,0.456 0.330,0.141 10 J156 2.32,1.513 2.572,1.73 2.572,1.73 2.729,1.73 false 2.32,1.093 2.572,0.876 2.572,0.876 2.729,0.876 false 0.133,0.08 0.585,0.222 0.452,0.141 10 *a 2.756,0.799 3.180,0.940 0.424,0.141 10 CANH 2.756,1.646 3.156,1.787 0.400,0.141 10 CANL

Disconnect the J156 brake control with bracket relay connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J156-4 (CANH) - J156-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Control with Bracket Relay)



OK

REPLACE BRAKE CONTROL WITH BRACKET RELAY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE CONTROL WITH BRACKET RELAY (CANH, CANL)

43.CONNECT CONNECTOR
a.

Reconnect the J75 No. 1 junction connector.



NEXT

44.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
44.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
a.
U152527E01
1.246,1.152 1.073,0.726 1.073,0.726 0.961,0.726 false 1.342,1.161 1.093,1.858 1.093,1.858 0.961,1.858 false 0.08,0.054 0.252,0.214 0.172,0.159 10 *a 1.568,0.576 1.836,0.713 0.268,0.137 10 A17 0.432,1.788 0.865,1.925 0.433,0.137 10 CANH 0.478,0.648 0.874,0.785 0.395,0.137 10 CANL

Disconnect the A17 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A17-12 (CANH) - A17-13 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

45.CONNECT CONNECTOR
a.

Reconnect the J75 No. 1 junction connector.



NEXT

46.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
46.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U152504E01
0.937,1.249 0.71,1.482 0.71,1.482 0.593,1.482 false 1.032,1.249 0.947,1.706 0.947,1.706 0.83,1.706 false 0.328,1.636 0.748,1.778 0.420,0.142 10 CANH 0.135,1.402 0.554,1.544 0.420,0.142 10 CANL 0.08,0.05 0.500,0.192 0.420,0.142 10 *a 1.612,0.212 1.855,0.354 0.244,0.142 10 J28

Disconnect the J28 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J28-39 (CANH) - J28-40 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)