Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › from 2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0445204 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Check Bus 4 Line  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen.
·

CAN main bus line, CAN branch line or connector

·

Central gateway ECU (network gateway ECU)

·

Airbag sensor assembly

·

Steering sensor

·

Skid control ECU (brake actuator assembly)

(for TMMF Made)

·

Electric brake booster (brake booster with master cylinder assembly)

(for TMMF Made)

·

Brake booster assembly with master cylinder

(for TMC Made)

·

Power steering ECU assembly

·

No. 1 global CAN junction connector

·

No. 2 global CAN junction connector



WIRING DIAGRAM

for TMC Made


C366140E09
1.354,0.719 1.969,0.917 0.615,0.198 10 false CAFH 1.354,1.219 1.969,1.417 0.615,0.198 10 false CAFL 1.833,0.594 2.115,0.844 0.281,0.25 10 false 26 1.833,1.146 2.115,1.396 0.281,0.25 10 false 27 2.688,0.604 2.969,0.854 0.281,0.25 10 false 1 2.635,1.135 2.917,1.385 0.281,0.25 10 false 12 4,0.604 4.333,0.771 0.333,0.167 10 false 2 3.969,1.156 4.302,1.323 0.333,0.167 10 false 13 3.969,1.594 4.302,1.76 0.333,0.167 10 false 15 3.979,1.927 4.313,2.094 0.333,0.167 10 false 4 2.51,2.385 3.094,2.552 0.583,0.167 10 false H113 2.51,2.552 4.167,3.021 1.656,0.469 10 false No. 2 Global CAN Junction Connector 4.969,0.604 5.302,0.771 0.333,0.167 10 false 24 4.969,1.135 5.302,1.302 0.333,0.167 10 false 23 5.25,0.604 5.865,0.802 0.615,0.198 10 false CA2H 5.25,1.135 5.865,1.333 0.615,0.198 10 false CA2L 5.135,1.646 5.75,1.844 0.615,0.198 10 false H40 5.135,1.802 7.083,2.302 1.948,0.5 10 false Central Gateway ECU (Network Gateway ECU) 1.333,3.635 1.948,3.833 0.615,0.198 10 false CANH 1.365,4.167 1.979,4.365 0.615,0.198 10 false CANL 1.854,3.531 2.135,3.781 0.281,0.25 10 false 3 1.854,4.083 2.135,4.25 0.281,0.167 10 false 8 2.677,3.542 2.958,3.708 0.281,0.167 10 false 2 2.625,4.094 2.906,4.26 0.281,0.167 10 false 13 3.99,3.542 4.271,3.708 0.281,0.167 10 false 4 3.969,4.073 4.25,4.24 0.281,0.167 10 false 15 3.99,5.677 4.271,5.844 0.281,0.167 10 false 3 3.969,6.198 4.25,6.365 0.281,0.167 10 false 14 2.635,6.188 2.917,6.354 0.281,0.167 10 false 12 2.698,5.667 2.979,5.833 0.281,0.167 10 false 1 1.833,5.688 2.115,5.854 0.281,0.167 10 false 7 1.833,6.208 2.115,6.375 0.281,0.167 10 false 8 4.969,5.677 5.25,5.844 0.281,0.167 10 false 43 4.969,6.208 5.25,6.375 0.281,0.167 10 false 42 5.26,5.792 5.875,5.99 0.615,0.198 10 false CA1H 5.25,6.333 5.865,6.531 0.615,0.198 10 false CA1L 5.01,6.688 5.625,6.885 0.615,0.198 10 false A38 5.01,6.865 6.563,7.365 1.552,0.5 10 false Brake Booster Assembly with Master Cylinder 2.583,6.719 3.198,6.917 0.615,0.198 10 false H110 2.583,6.885 4.25,7.292 1.667,0.406 10 false No. 1 Global CAN Junction Connector 0.49,6.698 1.104,6.896 0.615,0.198 10 false H1 0.49,6.854 1.792,7.469 1.302,0.615 10 false Power Steering ECU Assembly 1.354,5.667 1.969,5.865 0.615,0.198 10 false CANH 1.354,6.198 1.969,6.396 0.615,0.198 10 false CANL 0.74,4.552 1.354,4.75 0.615,0.198 10 false H39 0.729,4.719 2.927,4.969 2.198,0.25 10 false Steering Sensor 0.573,1.635 1.188,1.833 0.615,0.198 10 false H14 0.573,1.802 2.24,2.25 1.667,0.448 10 false Airbag Sensor Assembly


for TMMF Made


C403724E18
1.188,0.729 1.625,0.927 0.438,0.198 10 false CAFH 1.198,1.198 1.604,1.385 0.406,0.188 10 false CAFL 0.417,1.625 0.823,1.813 0.406,0.188 10 false H14 0.406,1.802 2.344,2.198 1.938,0.396 10 false Airbag Sensor Assembly 1.708,0.625 1.927,0.813 0.219,0.188 10 false 26 1.677,1.094 1.896,1.281 0.219,0.188 10 false 27 2.885,0.615 3.104,0.802 0.219,0.188 10 false 1 2.885,1.104 3.219,1.333 0.333,0.229 10 false 7 4.188,0.625 4.406,0.813 0.219,0.188 10 false 2 4.177,1.104 4.396,1.292 0.219,0.188 10 false 8 5.198,0.615 5.417,0.802 0.219,0.188 10 false 24 5.188,1.094 5.406,1.281 0.219,0.188 10 false 23 5.49,0.615 5.927,0.813 0.438,0.198 10 false CA2H 5.479,1.115 5.885,1.292 0.406,0.177 10 false CA2L 5.208,1.635 5.615,1.823 0.406,0.188 10 false H40 5.198,1.792 7.156,2.188 1.958,0.396 10 false Central Gateway ECU (Network Gateway ECU) 1.156,3.198 1.76,3.406 0.604,0.208 10 false CANH 1.177,3.688 1.688,3.865 0.51,0.177 10 false CANL 1.698,3.083 1.917,3.271 0.219,0.188 10 false 5 1.698,3.583 1.917,3.771 0.219,0.188 10 false 19 2.885,3.083 3.104,3.271 0.219,0.188 10 false 3 2.833,3.573 3.146,3.771 0.313,0.198 10 false 9 4.208,3.073 4.427,3.26 0.219,0.188 10 false 4 4.177,3.573 4.438,3.813 0.26,0.24 10 false 10 5.76,4.073 5.979,4.26 0.219,0.188 10 false A 6.24,4.083 6.458,4.271 0.219,0.188 10 false B 0.396,4.083 0.802,4.271 0.406,0.188 10 false A39 0.385,4.26 1.969,4.76 1.583,0.5 10 false Skid Control ECU (Brake Actuator Assembly) 2.719,4.104 3.125,4.292 0.406,0.188 10 false H112 2.708,4.292 5.219,4.583 2.51,0.292 10 false No. 2 Global CAN Junction Connector

C430892E05
0.667,2.573 1.781,2.813 1.115,0.24 10 false Steering Sensor 0.677,2.417 1.177,2.646 0.5,0.229 10 false H39 0.104,4.552 1.115,4.771 1.01,0.219 10 false A34*1, A35*2 0.083,4.719 2.51,5.115 2.427,0.396 10 false Electric Brake Booster (Brake Booster with Master Cylinder Assembly) 2.667,4.75 4.313,5.135 1.646,0.385 10 false No. 1 Global CAN Junction Connector 2.667,4.594 3.167,4.823 0.5,0.229 10 false H111 1.281,3.625 1.781,3.854 0.5,0.229 10 false CA1H 1.302,4.146 1.802,4.375 0.5,0.229 10 false CA1L 4.156,1.354 4.479,1.573 0.323,0.219 10 false 4 2.802,1.365 3.125,1.583 0.323,0.219 10 false 2 2.813,3.51 3.135,3.729 0.323,0.219 10 false 3 2.813,4.052 3.135,4.271 0.323,0.219 10 false 9 1.771,4.052 2.094,4.271 0.323,0.219 10 false 10 1.781,3.521 2.104,3.74 0.323,0.219 10 false 18 1.792,1.917 2.115,2.135 0.323,0.219 10 false 8 1.781,1.385 2.104,1.604 0.323,0.219 10 false 3 4.135,3.521 4.458,3.74 0.323,0.219 10 false 1 4.146,4.052 4.469,4.271 0.323,0.219 10 false 7 5.281,1.083 5.604,1.302 0.323,0.219 10 false A 5.594,1.083 5.917,1.302 0.323,0.219 10 false B 1.271,1.479 1.771,1.708 0.5,0.229 10 false CANH 1.292,2.021 1.792,2.25 0.5,0.229 10 false CANL 2.802,1.917 3.125,2.135 0.323,0.219 10 false 8 4.115,1.906 4.438,2.125 0.323,0.219 10 false 10 5.313,3.521 5.813,3.75 0.5,0.229 10 false CANH 5.323,4.052 5.823,4.281 0.5,0.229 10 false CANL 5.125,4.042 5.448,4.26 0.323,0.219 10 false 8 5.115,3.521 5.438,3.74 0.323,0.219 10 false 7 5.156,4.521 5.656,4.75 0.5,0.229 10 false H1 5.156,4.688 7.156,5.01 2,0.323 10 false Power Steering ECU Assembly 4.979,5.125 6.667,5.323 1.688,0.198 10 false *1: for LHD 4.979,5.438 6.667,5.635 1.688,0.198 10 false *2: for RHD


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C425195C72
1.51,0.073 1.927,0.323 0.417,0.25 2.292,0.885 2.802,1.677 true 2.198,0.844 2.656,0.198 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.135 2.063,0.333 0.458,0.198 10 false H40 2.854,1.656 3.323,1.875 0.469,0.219 10 false CA2L 2.688,0.094 3.167,0.26 0.479,0.167 10 false CA2H
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-24 (CA2H) - H40-23 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES

NG

86.CHECK VEHICLE TYPE
2.CHECK FOR SHORT IN CAN BUS LINES
a.
C425195C72
1.51,0.073 1.927,0.323 0.417,0.25 2.292,0.885 2.802,1.677 true 2.198,0.844 2.656,0.198 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.135 2.063,0.333 0.458,0.198 10 false H40 2.854,1.656 3.323,1.875 0.469,0.219 10 false CA2L 2.688,0.094 3.167,0.26 0.479,0.167 10 false CA2H
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-24 (CA2H) - H40-23 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Result
OK
NG



OK

3.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

59.CHECK VEHICLE TYPE
3.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C53
1.844,0.198 2.313,0.448 0.469,0.25 5.333,0.292 5.75,0.563 0.417,0.271 6.313,1.615 6.552,1.969 true 2.656,1.292 3.177,2.073 true 2.573,1.25 2.969,0.583 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 3.229,2.031 3.781,2.229 0.552,0.198 10 false CA2L 6.604,1.948 7.156,2.146 0.552,0.198 10 false BAT 3.031,0.479 3.583,0.677 0.552,0.198 10 false CA2H 5.427,0.344 5.74,0.542 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-24 (CA2H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-23 (CA2L) - H3-16 (BAT)



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

32.CHECK VEHICLE TYPE
4.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C54
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.135 5.729,0.406 0.417,0.271 5.458,1.021 6.031,0.531 true 2.656,1.313 3.24,2.083 true 2.573,1.24 3.115,0.531 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 3.281,2.052 3.833,2.25 0.552,0.198 10 false CA2L 6.073,0.406 6.625,0.604 0.552,0.198 10 false CG 3.177,0.438 3.729,0.635 0.552,0.198 10 false CA2H 5.417,0.188 5.729,0.385 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-24 (CA2H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-23 (CA2L) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

5.CHECK VEHICLE TYPE
5.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

18.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H113 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113,H3)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H113-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H113-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113,H3)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H113-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to No. 1 Global CAN Junction Connector
H113-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

NG

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113,H3)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H113-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Airbag Sensor Assembly
H113-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113,H3)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H113-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H113-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H14 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113,H3)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H113-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Airbag Sensor Assembly
H113-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H110 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to No. 2 Global CAN Junction Connector
H110-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Brake Booster Assembly with Master Cylinder
H110-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)
13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Steering Sensor
H110-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Power Steering ECU Assembly
H110-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

17.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)
a.

Disconnect the A38 brake booster assembly with master cylinder connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Brake Booster Assembly with Master Cylinder
H110-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)

16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the H39 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Steering Sensor
H110-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

17.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the H1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Power Steering ECU Assembly
H110-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

18.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H112 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H112-8 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

19.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

22.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
19.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to No. 1 Global CAN Junction Connector
H112-10 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

20.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

NG

25.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
20.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Airbag Sensor Assembly
H112-7 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

21.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

NG

23.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
21.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Skid Control ECU (Brake Actuator Assembly)
H112-9 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

24.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
22.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H112-8 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

23.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H14 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Airbag Sensor Assembly
H112-7 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

24.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Disconnect the A39 skid control ecu (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Skid Control ECU (Brake Actuator Assembly)
H112-9 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

25.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H111 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to No. 2 Global CAN Junction Connector
H111-10 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

26.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

26.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Electric Brake Booster (Brake Booster with Master Cylinder Assembly)
H111-9 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

27.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

29.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
27.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Steering Sensor
H111-8 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

28.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

30.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
28.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Power Steering ECU Assembly
H111-7 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

31.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
29.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
a.

Disconnect the A34*1 or A35*2 electric brake booster (brake booster with master cylinder assembly) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Electric Brake Booster (Brake Booster with Master Cylinder Assembly)
H111-9 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

30.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the H39 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Steering Sensor
H111-8 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

31.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the H1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Power Steering ECU Assembly
H111-7 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

32.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

33.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

45.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
33.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H113 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H110-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

34.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

36.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
34.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113,H3)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H113-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to No. 1 Global CAN Junction Connector
H113-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

35.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

NG

38.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
35.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113,H3)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H113-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Airbag Sensor Assembly
H113-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

37.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
36.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113,H3)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H113-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H113-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

37.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H14 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113,H3)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H113-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Airbag Sensor Assembly
H113-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

38.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H110 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to No. 2 Global CAN Junction Connector
H110-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

39.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

39.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Brake Booster Assembly with Master Cylinder
H110-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

40.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

42.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)
40.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Steering Sensor
H110-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

41.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

43.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
41.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Power Steering ECU Assembly
H110-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

44.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
42.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)
a.

Disconnect the A38 brake booster assembly with master cylinder connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Brake Booster Assembly with Master Cylinder
H110-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)

43.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the H39 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Steering Sensor
H110-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

44.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the H1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110,H3)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H110-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Power Steering ECU Assembly
H110-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

45.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H112 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H112-8 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

46.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

49.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
46.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to No. 1 Global CAN Junction Connector
H112-10 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

47.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

NG

52.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
47.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Airbag Sensor Assembly
H112-7 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

48.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

NG

50.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
48.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Skid Control ECU (Brake Actuator Assembly)
H112-9 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

51.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
49.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H112-8 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

50.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H14 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Airbag Sensor Assembly
H112-7 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

51.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Disconnect the H14 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112,H3)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H112-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Skid Control ECU (Brake Actuator Assembly)
H112-9 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

52.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H111 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to No. 2 Global CAN Junction Connector
H111-10 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

53.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

53.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Electric Brake Booster (Brake Booster with Master Cylinder Assembly)
H111-9 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

54.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

56.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
54.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Steering Sensor
H111-8 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

55.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

57.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
55.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Power Steering ECU Assembly
H111-7 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

58.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
56.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
a.

Disconnect the A34*1 or A35*2 electric brake booster (brake booster with master cylinder assembly) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Electric Brake Booster (Brake Booster with Master Cylinder Assembly)
H111-9 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

57.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the H39 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Steering Sensor
H111-8 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

58.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the H1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111,H3)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H111-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Power Steering ECU Assembly
H111-7 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

59.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

60.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

72.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
60.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H113 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H113-2 (CANH) - H113-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

61.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

63.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
61.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H113-4 (CANH) - H113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 1 Global CAN Junction Connector



Result:
Result
OK
NG



OK

62.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

NG

65.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
62.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H113-1 (CANH) - H113-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Airbag Sensor Assembly



Result:
Result
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

64.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
63.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H113-2 (CANH) - H113-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

64.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H14 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H113-1 (CANH) - H113-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Airbag Sensor Assembly



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

65.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H110 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H110-4 (CANH) - H110-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 2 Global CAN Junction Connector



Result:
Result
OK
NG



OK

66.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

66.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H110-3 (CANH) - H110-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Brake Booster Assembly with Master Cylinder



Result:
Result
OK
NG



OK

67.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

69.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)
67.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H110-2 (CANH) - H110-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Steering Sensor



Result:
Result
OK
NG



OK

68.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

70.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
68.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H110-1 (CANH) - H110-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Power Steering ECU Assembly



Result:
Result
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

71.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
69.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)
a.

Disconnect the A38 brake booster assembly with master cylinder connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H110-3 (CANH) - H110-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Brake Booster Assembly with Master Cylinder



Result:
Result
OK
NG



OK

REPLACE BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER)

70.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the H39 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H110-2 (CANH) - H110-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Steering Sensor



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

71.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the H1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H110-1 (CANH) - H110-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Power Steering ECU Assembly



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

72.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H112 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H112-2 (CANH) - H112-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

73.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

76.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
73.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H112-4 (CANH) - H112-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to No. 1 Global CAN Junction Connector



Result:
Result
OK
NG



OK

74.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

NG

79.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
74.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H112-1 (CANH) - H112-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Airbag Sensor Assembly



Result:
Result
OK
NG



OK

75.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

NG

77.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
75.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H112-3 (CANH) - H112-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Skid Control ECU (Brake Actuator Assembly)



Result:
Result
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

78.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
76.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H112-2 (CANH) - H112-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

77.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H14 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H112-1 (CANH) - H112-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Airbag Sensor Assembly



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

78.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Disconnect the A39 skid control ecu (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H112-3 (CANH) - H112-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Skid Control ECU (Brake Actuator Assembly)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

79.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H110 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H111-4 (CANH) - H111-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to No. 2 Global CAN Junction Connector



Result:
Result
OK
NG



OK

80.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

80.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H111-3 (CANH) - H111-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Electric Brake Booster (Brake Booster with Master Cylinder Assembly)



Result:
Result
OK
NG



OK

81.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

83.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
81.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H111-2 (CANH) - H111-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Steering Sensor



Result:
Result
OK
NG



OK

82.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

84.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
82.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H111-1 (CANH) - H111-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Power Steering ECU Assembly



Result:
Result
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

85.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
83.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
a.

Disconnect the A34*1 or A35*2 electric brake booster (brake booster with master cylinder assembly) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H111-3 (CANH) - H111-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Electric Brake Booster (Brake Booster with Master Cylinder Assembly)



Result:
Result
OK
NG



OK

REPLACE ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ELECTRIC BRAKE BOOSTER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

84.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the H39 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H111-2 (CANH) - H111-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Steering Sensor



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

85.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the H1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H111-1 (CANH) - H111-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Power Steering ECU Assembly



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

86.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

87.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

93.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
87.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-24 (CA2H) - H40-23 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 2 Global CAN Junction Connector



Result:
Result
OK
NG



OK

NG

88.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
88.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H113 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H113-2 (CANH) - H113-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

89.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

89.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H113)Location & Routing

Click Connector(H113)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H113-4 (CANH) - H113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 1 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

90.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
90.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H110 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H110-4 (CANH) - H110-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 2 Global CAN Junction Connector



Result:
Result
OK
NG



OK

91.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

91.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H110)Location & Routing

Click Connector(H110)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H110-1 (CANH) - H110-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Power Steering ECU Assembly



Result:
Result
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

92.CHECK FOR OPEN IN CAN MAIN BUS LINES (POWER STEERING ECU ASSEMBLY)
92.CHECK FOR OPEN IN CAN MAIN BUS LINES (POWER STEERING ECU ASSEMBLY)
a.

Disconnect the H1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H1)Location & Routing

Click Connector(H1)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assembly

H1-7 (CANH) - H1-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 1 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (POWER STEERING ECU ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

93.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-24 (CA2H) - H40-23 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 2 Global CAN Junction Connector



Result:
Result
OK
NG



OK

NG

94.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
94.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H112 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H112-2 (CANH) - H112-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

95.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

95.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H112)Location & Routing

Click Connector(H112)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Global CAN Junction Connector

H112-4 (CANH) - H112-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 1 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

96.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
96.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H110 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H111-4 (CANH) - H111-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 2 Global CAN Junction Connector



Result:
Result
OK
NG



OK

97.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

97.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H111)Location & Routing

Click Connector(H111)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Global CAN Junction Connector

H111-1 (CANH) - H111-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Power Steering ECU Assembly



Result:
Result
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

98.CHECK FOR OPEN IN CAN MAIN BUS LINES (POWER STEERING ECU ASSEMBLY)
98.CHECK FOR OPEN IN CAN MAIN BUS LINES (POWER STEERING ECU ASSEMBLY)
a.

Disconnect the H1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H1)Location & Routing

Click Connector(H1)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assembly

H1-7 (CANH) - H1-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 1 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (POWER STEERING ECU ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)