Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2014.07–2015.06
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P1604  Startability Malfunction  


DESCRIPTION

This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.

Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1604 Either condition is met. (1 trip detection logic):
·

The engine speed is below 500 rpm with the STA signal on for a certain amount of time (refer to the illustration below).*1

·

After the engine starts (engine speed is 500 rpm or more), the engine speed drops to 200 rpm or less within approximately 2 seconds.*2


·

Immobiliser system*3

·

Engine assembly (excess friction, compression loss)

·

Starter assembly

·

Crankshaft position sensor

·

Camshaft position sensor

·

Engine coolant temperature sensor

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line (fuel filter, pipes and hoses)

·

Fuel injector assembly

·

Throttle with motor body assembly

·

Fuel pressure regulator

·

Battery

·

Drive plate and ring gear sub-assembly*4

·

Flywheel sub-assembly*5

·

Spark plug

·

Ignition coil circuit

·

Intake system

·

Camshaft timing oil control valve assembly

·

Mass air flow meter

·

Heated oxygen sensor (sensor 1)

·

Valve timing

·

Fuel

·

Purge VSV

·

Intake valve

·

ECM



*1: In case that the engine is difficult to start or that the engine does not start.

*2: In case that the engine speed drops or the engine stalls right after engine start.

*3: w/ Immobiliser System

*4: for Automatic Transaxle

*5: for Manual Transaxle

A220316E01
0.314,1.641 1.192,1.824 0.878,0.184 10 Starting Time 1.276,0.37 1.960,0.554 0.684,0.184 10 (Seconds) 3.844,1.136 5.000,1.486 1.156,0.350 10 Region Indicating Malfunction 6.401,2.662 6.682,2.859 0.281,0.198 10 (°C) 1.43,2.26 1.553,2.437 0.123,0.177 10 2 1.883,2.78 2.122,2.936 0.239,0.156 10 -30 3.499,2.78 3.696,2.950 0.198,0.170 10 20 5.189,2.78 5.401,2.964 0.211,0.184 10 80 3.518,3.178 5.368,3.362 1.850,0.184 10 Engine Coolant Temperature

Reference waveforms showing a normal cold engine start


A259947


Reference waveforms showing a normal warm engine start


A258726


Reference values when there is an air leak in the air induction system during starting difficulty


Freeze Frame Data P1604 Startability Malfunction
Engine and ECT
Current P1604: Startability Malfunction
Time Freeze Frame Data
Item Data1 Data2 Data3 Data4 Data5 Unit
Engine Speed 253 1382 582 196 157 rpm
Calculate Load 94.1 42.7 25.0 94.1 94.1 %
Vehicle Load 9.8 6.6 14.1 17.2 15.2 %
MAF 0.32 1.18 1.07 0.43 0.31 gm/s
Atmosphere Pressure 103 103 103 103 103 kPa
Coolant Temp 89 89 89 89 89 °C
Intake Air 48 48 48 48 48 °C
Ambient Temperature 25 25 25 25 25 °C
Battery Voltage 10.351 12.421 12.578 12.285 12.226 V
Throttle Sensor Volt % 20.3 17.6 20.3 20.3 20.3 %
Throttle Sensor #2 Volt % 53.3 49.4 53.3 53.3 53.3 %
Throttle Sensor Position 1.5 0.0 1.5 1.5 1.5 %
Throttle Motor DUTY 20.3 17.6 20.3 20.3 20.3 %
Injector (Port) 8624 4102 2944 2545 2545 μs
Injection Volume (Cylinder 1) 0.153 0.153 0.133 0.133 0.133 ml
Fuel Pump/Speed Status ON ON ON ON ON
EVAP (Purge) VSV 0.0 0.0 0.0 0.0 0.0 %
Evap Purge Flow 0.0 0.0 0.0 0.0 0.0 %
Purge Density Learn Value 0.000 0.000 0.000 0.000 0.000
EVAP purge VSV OFF OFF OFF OFF OFF
Target Air-Fuel Ratio 1.186 1.167 1.136 1.110 1.186
O2S B1S1 0.015 0.015 0.015 0.015 0.015 V
O2S B1 S2 0.000 0.015 0.000 0.000 0.000 V
Short FT #1 0.000 0.000 0.000 0.000 0.000 %
Long FT #1 -5.469 -4.688 -5.469 -4.688 -5.469 %
Total FT #1 0.000 0.000 0.000 0.000 0.000
Fuel System Status #1 Unused OL OL Unused Unused
IGN Advance 5.0 5.0 13.0 11.5 11.5 deg
Knock Feedback Value -1.5 -1.5 -1.5 -1.5 -1.5 °CA
Knock Correct Learn Value 10.2 10.2 10.2 10.2 10.2 °CA
VVT Control Status #1 OFF OFF OFF OFF OFF
Starter Signal ON OFF OFF OFF OFF


WIRING DIAGRAM

Refer to P0100 for the mass air flow meter circuit (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0100).

Refer to P0115 for the engine coolant temperature sensor circuit (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0115).

Refer to P0335 for the crankshaft position sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0335).

Refer to P0351 for the ignition coil circuit (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0351).

Refer to P0443 for the purge VSV circuit (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0443).

Refer to Fuel Pump Control Circuit (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>Fuel Pump Control Circuit).

Refer to Fuel Injector Circuit (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit).

Refer to Starter Signal Circuit (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>Starter Signal Circuit).

CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.

As the DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

When the Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.

·

Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

·

When confirming the freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to start the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and compare it with the freeze frame data.

·

If the malfunction does not reoccur, carefully check the vehicle conditions from when the malfunction occurred using freeze frame data.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.

·

If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.



Malfunction Recurrence and Inspection Areas


a.

Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

i.

The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).

HINT:

One of the following problems may be present: battery depletion, excess engine friction, a starter malfunction or a crankshaft position sensor malfunction.


·

If the battery voltage is less than 6 V during cranking, there is a high probability that engine friction is abnormal.

·

If the battery voltage drops to 5 V or less when starting the engine, the battery may be malfunctioning.

·

If the battery voltage fluctuates while cranking the engine, it can be concluded that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor and/or an ECM may be malfunctioning.

A215383E32
0.133,0.091 4.289,0.274 4.156,0.184 10 When the engine speed for all 5 sets of freeze frame data is 0 rpm: 0.306,1.08 1.573,1.597 1.267,0.517 10 Was the minimum battery voltage 5 V or higher? 2.267,1.08 3.479,1.625 1.211,0.545 10 Was the minimum battery voltage 6 V or higher? 4.061,1.071 5.244,1.450 1.184,0.378 10 Did the battery voltage fluctuate? 5.674,1.033 7.084,1.397 1.410,0.364 10 Inspect the crankshaft position sensor 0.866,3.073 2.161,3.423 1.295,0.350 10 Recharge or replace the battery 2.976,2.933 4.178,3.297 1.202,0.364 10 Inspect the engine assembly 5.209,2.942 6.393,3.109 1.184,0.167 10 Inspect the starter 0.825,4.746 1.166,4.898 0.341,0.151 10 YES 0.825,5.223 1.082,5.388 0.258,0.165 10 NO



ii.

All engine speeds recorded in the freeze frame data are between 60 and 250 rpm (the engine cranks but there is no combustion).

HINT:

If the engine speed is between 60 and 250 rpm (no initial combustion), there may be a wiring problem or a complete failure of an ignition or fuel system part.


·

Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and the engine may not be able to be started.

A215384E14
0.082,0.086 2.821,0.270 2.739,0.184 10 Engine speed is between 60 and 250 rpm: 0.39,0.913 1.851,1.457 1.461,0.545 10 Has an ignition system DTC (IGF, NE, G, etc.) been output? 2.94,0.913 4.290,1.263 1.350,0.350 10 Is the engine coolant temperature normal? 5.294,0.913 6.755,1.124 1.461,0.211 10 Inspect the fuel system 1.483,2.622 3.139,3.139 1.656,0.517 10 Repair the malfunctioning areas indicated by the output DTCs 5.364,2.636 6.631,3.181 1.267,0.545 10 Replace the engine coolant temperature sensor 0.922,4.471 1.245,4.627 0.323,0.156 10 YES 0.922,5.06 1.189,5.216 0.267,0.156 10 NO



iii.

The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).

HINT:

If the engine speed is 250 rpm or higher (combustion occurs but the initial combustion and starter turnoff timing is too late), the fuel injection volume is often incorrect (too low or too high) and determining the cause of the malfunction is often difficult.


·

Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and engine starting trouble may occur.

·

If Long FT #1 is incorrect, there may be a fuel supply problem due to the injectors or fuel pump being clogged, etc.

·

If the engine cranking speed is too high, compression loss may have occurred due to carbon interfering with the valve operation.

A215383E98
0.104,0.073 2.396,0.281 2.292,0.208 10 false Engine speed is 250 rpm or higher: 0.229,1.031 1.583,1.604 1.354,0.573 10 false Was "Coolant Temp" normal? 2.25,1.021 3.458,1.604 1.208,0.583 10 false Was "Long FT" normal (within +/- 15%)? 4.125,1.031 5.156,1.573 1.031,0.542 10 false Was the engine cranking speed too high? 5.75,1.031 6.948,1.406 1.198,0.375 10 false Inspect the engine assembly 0.875,2.948 2.125,3.51 1.25,0.563 10 false Replace the engine coolant temperature sensor 3.063,2.938 4.365,3.344 1.302,0.406 10 false Inspect the injectors and fuel pump 5.208,2.938 6.677,3.333 1.469,0.396 10 false Inspect the fuel system and intake system 0.823,4.75 1.25,5 0.427,0.25 10 false YES 0.823,5.229 1.167,5.417 0.344,0.188 10 false NO




b.

When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, perform the following inspections ("Problem symptoms" and "Systems to inspect")

i.

Problem symptoms

1.

The engine does not crank.

HINT:

The starter is normal if a noise that indicates the starter pinion gear is extending is heard. The battery may be fully depleted or there may be excess engine friction.


2.

The engine cranking speed is abnormal.

HINT:

If the engine cranking speed is too high (for example, 300 rpm or higher with no combustion), compression loss may have occurred because carbon interfered with valve operation, etc.


3.

There is no initial combustion.

HINT:

If there is no initial combustion, there is probably a wiring problem or an ignition or fuel system part malfunction.


4.

The engine stalls after starter turnoff.

HINT:

If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the VVT may have a problem returning.


5.

The initial combustion and starter turnoff occur late.

HINT:

If the initial combustion and starter turnoff occur late, the fuel injection volume is probably incorrect (too low or too high).


HINT:

Causes of fuel system malfunctions according to conditions present at the time of the malfunction.

·

When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.

·

When 15 to 120 minutes have elapsed after stopping the engine: Problem with injector fuel seal.

·

When a long time has elapsed after stopping the engine: Pressure regulator is stuck open.





ii.

Systems to inspect.

1.

Intake system

2.

Ignition system

3.

Fuel system





INSPECTION FLOW


a.

Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

Freeze Frame Data Item Result Suspected Area Procedure
Engine Speed 0 rpm (no engine cranking at all)
·

Battery fully depleted

·

Engine assembly (excess friction)

·

Starter assembly

·

Crankshaft position sensor

·

ECM


4 to 9
60 to 250 rpm (engine cranks but no initial combustion*2)
·

Fuel pump control circuit

·

Ignition system

·

Immobiliser system*1

·

Engine coolant temperature sensor

·

Fuel injection system


10 to 14
250 rpm or higher (combustion occurs but initial combustion and starter turnoff*3 occur late)
·

Engine assembly (compression loss)

·

Fuel injection system

·

Fuel pump control circuit


15 to 23

*1: w/ Immobiliser System

HINT:
·

*2: First combustion after cranking begins.

·

*3: Condition when engine speed increases and starter can be turned off.




b.

When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.

i.

Problem symptoms

Problem Symptom Suspected Area Suspected Component Procedure
The engine does not crank Battery malfunction
·

Battery fully depleted


26 to 31
Starting system
·

Starter assembly (includes pinion gear wear or tooth damage)

·

Starting system


Engine assembly
·

Engine assembly (excess friction)

·

Drive plate wear or tooth damage*1

·

Flywheel wear or tooth damage*2


Cranking speed too low Battery malfunction
·

Battery fully depleted


32 to 34
Starting system
·

Starter assembly


Engine assembly
·

Engine assembly (excess friction)


Cranking speed too high Engine assembly
·

Engine assembly (compression loss)


There is no initial combustion Fuel supply problem
·

Cannot maintain pressure due to pressure regulator malfunction

·

Fuel injector leak

·

Fuel leak from fuel line

·

Fuel pump control circuit

·

Fuel pump


35 to 48
Immobiliser system
·

Immobiliser system*3


Ignition system malfunction
·

Spark plug

·

Crankshaft position sensor

·

No. 1 ignition coil


Engine stalls after starter turnoff Air suction
·

Intake system connections


49 to 54
Deposits in throttle body
·

Throttle with motor body assembly


VVT valve does not return properly
·

Camshaft timing oil control valve assembly


Mass air flow meter malfunction
·

Mass air flow meter


The initial combustion and starter turnoff occur late Engine coolant temperature sensor malfunction
·

Engine coolant temperature sensor


55 to 68
Mass air flow meter malfunction
·

Mass air flow meter


Abnormal A/F learning value
·

Heated oxygen sensor (sensor 1)


Deviation from fuel injection characteristics
·

Fuel injector assembly


Wet-fouled or dry-fouled spark plug
·

Spark plug


Lack of fuel pressure
·

Pressure regulator

·

Fuel pump

·

Fuel pump control circuit



*1: for Automatic Transaxle

*2: for Manual Transaxle

*3: w/ Immobiliser System


ii.

Systems to inspect.

Troubleshooting by System Suspected Area Suspected Component Procedure
Fuel system troubleshooting A Abnormal air-fuel ratio learning value
·

Fuel injector assembly


83 to 90
91 to 98
Rough idling
·

Crankshaft position sensor


Abnormal fuel pressure
·

Fuel

·

Fuel leak from fuel line

·

Fuel pump

·

Pressure regulator


Fuel system troubleshooting B Abnormal concentration of HC in surge tank
·

Purge VSV system

·

Fuel injector assembly


99 to 101
Fuel system troubleshooting C Injection signal system malfunction
·

Fuel injector assembly

·

Crankshaft position sensor

·

Camshaft position sensor

·

ECM


70 to 73
Intake system troubleshooting Difference between ISC target value and opening angle when idling
·

Engine assembly (compression loss)

·

Valve timing

·

Engine coolant temperature sensor

·

ECM


80 to 82
102 to 104
Ignition system troubleshooting Camshaft and/or crankshaft position sensor signal malfunction
·

Crankshaft position sensor system (including sensor installation)

·

Camshaft position sensor system (including sensor installation)

·

ECM


74 to 79
105 to 110




NOTICE:
·

Inspect the fuses circuit related to this system before performing the following inspection procedure

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.
A103809E46
2.302,0.073 3.24,0.281 0.938,0.208 10 false DTC is stored 1.323,1.063 2.104,1.24 0.781,0.177 10 false 0.5 seconds 0.354,1.052 1.135,1.25 0.781,0.198 10 false 0.5 seconds 0.333,2.865 2.677,3.063 2.344,0.198 10 false Freeze frame data recorded point 2.271,1.052 3.052,1.25 0.781,0.198 10 false 0.5 seconds 0.219,2.479 0.313,2.635 0.094,0.156 10 false 1 1.167,2.479 1.281,2.625 0.115,0.146 10 false 2 2.104,2.458 2.208,2.604 0.104,0.146 10 false 3 2.708,2.625 2.823,2.792 0.115,0.167 10 false 4 3.063,2.438 3.167,2.594 0.104,0.156 10 false 5

Read DTCs and record the Freeze Frame Data.

HINT:
·

This freeze frame data shows the actual engine conditions when engine starting trouble occurred.

·

When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.

·

The fourth set of freeze frame data is the data recorded when then the DTC is stored.



Result
Result Proceed to
DTC P1604 is output A
DTC P1604 and other DTCs are output B



A

2.CHECK ENGINE IMMOBILISER SYSTEM

B

2.CHECK ENGINE IMMOBILISER SYSTEM
HINT:

If the vehicle is not equipped with a immobiliser system, proceed to next step (OK).


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Fuel Cut.


e.

Read the value displayed on the tester.

OK:

Immobiliser Fuel Cut is OFF


HINT:

If the engine is cranked immediately after reconnecting the battery cable (key verification for immobiliser system not completed), the engine cannot be started. Key verification needs to wait for several seconds after turning the ignition switch to ON.




OK

3.CHECK MALFUNCTION CONDITION

NG

3.CHECK MALFUNCTION CONDITION
a.

Confirm the problem symptoms.

Result
Result Proceed to
Freeze frame data exists, but the starting difficulty cannot be reproduced and it is unknown what kind of starting difficulty occurred A
The problem symptoms can be reproduced, or the malfunction conditions are known B



A

4.READ FREEZE FRAME DATA

B

25.CONFIRM PROBLEM SYMPTOM
4.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Suspected Area Proceed to
Engine Speed Battery Voltage
All 5 sets of freeze frame data are 0 rpm (no engine cranking at all) Minimum voltage is less than 5 V Battery fully depleted A
Minimum voltage is 5 V or higher
·

Starter malfunction

·

Crankshaft position sensor system

·

Excess engine friction

·

ECM


B
60 to 250 rpm (engine cranks but no initial combustion) -
·

Fuel pump control circuit

·

Ignition system

·

Engine coolant temperature sensor

·

Fuel injection system


C
250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late) -
·

Engine assembly

·

Engine coolant temperature sensor

·

Fuel injection system

·

Fuel pump control circuit


D

Result
Freeze Frame Data Item Suspected Area Proceed to
Low Rev for Eng Start
ON exists
·

Intake system connections

·

Throttle with motor body assembly

·

Camshaft timing oil control valve assembly

·

Mass air flow meter


E

HINT:

When DTC P1604 is stored, either "Engine Start Hesitation"*1 or "Low Rev for Eng Start"*2 in the Freeze Frame Data will be ON. If "Low Rev for Eng Start" is ON, proceed to E.

*1: This value turns ON when the engine speed does not reach a certain value for a certain period of time when starting the engine.

*2: This value turns ON when the engine stalls immediately after starting the engine. If "Low Rev for Eng Start" is ON, as there is a possibility that the low engine speed or engine stall was caused by the user, confirm the following freeze frame data items.

·

Immobiliser Fuel Cut

·

Engine Speed (Starter Off)

·

Shift SW Status [R, D Range] (for Automatic Transaxle)





A

CHARGE OR REPLACE BATTERY

B

5.READ FREEZE FRAME DATA

C

10.READ FREEZE FRAME DATA

D

15.READ FREEZE FRAME DATA

E

49.INSPECT MASS AIR FLOW METER
5.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Battery Voltage Minimum voltage is 6 V or higher and voltage does not fluctuate*1 Starter system A
Minimum voltage is 6 V or higher and voltage fluctuates*2, *3
·

Crankshaft position sensor system

·

ECM


B
Minimum voltage is 5 to 6 V*4
·

Excess engine friction

·

Battery fully depleted


C

HINT:
·
A217930E01
0.97,0.0060 2.223,0.176 1.253,0.17 10 Freeze Frame Data 0.97,1.742 2.223,1.912 1.253,0.17 10 Freeze Frame Data 0.162,0.178 0.777,0.668 0.615,0.49 10 Voltage does not Fluctuate 0.128,2.086 0.815,2.419 0.688,0.333 10 Voltage Fluctuates

*1: The 5 sets of freeze frame data show approximately the same battery voltage.

·

*2: The 5 sets of freeze frame data show different battery voltages.

·

*3: If the voltage fluctuates, it can be determined that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor system and/or the ECM may be malfunctioning.

·

*4: There may be excess engine friction. Make sure that the crankshaft rotates smoothly when turning it by hand. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.





A

B

6.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

C

CHECK AND REPAIR ENGINE ASSEMBLY OR BATTERY

6.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

7.INSPECT CRANKSHAFT POSITION SENSOR

NG

7.INSPECT CRANKSHAFT POSITION SENSOR
a.

Disconnect the crankshaft position sensor connector.


b.

Check for oil on the connector terminals.

OK:

No oil on the terminals.




OK

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0335 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0335).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

9.CHECK CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

10.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Suspected Area Proceed to
Coolant Temp, Ambient Temperature, Intake Air Coolant Temp, Ambient Temperature Fuel Pump/Speed Status
Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C (18°F) or more*1 Coolant Temp is 125°C (257°F) or more, or lower than Ambient Temperature by 15°C (27°F) or more - Engine coolant temperature sensor A
Other than above All 5 sets of freeze frame data are ON - B
At least 1 of the 5 sets of freeze frame data is OFF Fuel pump control circuit C
Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C (18°F) *2 - At least 1 of the 5 sets of freeze frame data is OFF Fuel pump control circuit C
All 5 sets of freeze frame data are ON - B

HINT:
·

*1: A long time had not elapsed after stopping the engine.

·

*2: A long time had elapsed after stopping the engine.





A

B

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)

C

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Disconnect the fuel pump connector.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


e.
U158065E02
0.188,0.104 0.385,0.26 0.198,0.156 10 false *a 1.573,0.406 1.938,0.594 0.365,0.188 10 false K17

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K17-4 - Body ground Active Test is being performed 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Fuel Pump)

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0300).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)

NG

13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


d.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
Fuel leakage or signs of fuel leakage are present A
No fuel leakage or signs of fuel leakage B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.





A

REPAIR OR REPLACE FUEL LINE

B

14.CHECK FUEL SYSTEM
14.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B

HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

REPAIR OR REPLACE FUEL SYSTEM

B

24.PERFORM SIMULATION TEST
15.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Suspected Area Proceed to
Coolant Temp, Ambient Temperature, Intake Air Coolant Temp, Ambient Temperature Long FT #1 Engine Speed
Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C (18°F) or more Coolant Temp is 125°C (257°F) or more, or lower than Ambient Temperature by 15°C (27°F) or more - - Engine coolant temperature sensor A
Other than above -15% or less, or +15% or more -
·

Fuel pump control circuit

·

Fuel injector assembly


B
-15 to +15% Minimum speed is 300 rpm or more*1 Engine assembly C
Minimum speed is below 300 rpm
·

Fuel system

·

Intake air system


D
Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C (18°F) - -15% or less, or +15% or more -
·

Fuel pump control circuit

·

Fuel injector assembly


B
-15 to +15% Minimum speed is 300 rpm or more*1 Engine assembly C
Minimum speed is below 300 rpm
·

Fuel system

·

Intake air system


D

HINT:

*1: Compression loss may have occurred in the engine assembly.




A

B

16.INSPECT FUEL INJECTOR ASSEMBLY

C

CHECK AND REPAIR ENGINE ASSEMBLY

D

18.READ FREEZE FRAME DATA
16.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check that no carbon is stuck to the fuel injector assembly.

OK:

No carbon present.




OK

17.CHECK FUEL SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

17.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B

HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

REPAIR OR REPLACE FUEL SYSTEM

B

24.PERFORM SIMULATION TEST
18.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON end turn the tester on.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Coolant Temp Engine coolant temperature is 40°C (104°F) or less*1 Pressure regulator A
Engine coolant temperature is 40 to 90°C (104 to 194°F)*2 Fuel injector assembly B
Engine coolant temperature is 90°C (194°F) or more*3 Pressure regulator A

HINT:

*1: If the engine coolant temperature is 40°C [104°F] or less (after stopping the engine and the vehicle is not driven for a long period of time), the pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*2: If the engine coolant temperature is 40 to 90°C [104 to 194°F] (15 to 120 minutes have passed after stopping the engine), there may be fuel leaking from a fuel injector assembly.

*3: If the engine coolant temperature is 90°C [194°F] or more (2 to 5 minutes have passed after stopping the engine), there may be a problem with the pressure regulator failing to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.




A

19.CHECK FUEL PRESSURE

B

20.INSPECT FUEL INJECTOR ASSEMBLY
19.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

Standard:

147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)


HINT:

If the engine cannot be started, read the values after cranking the engine.


Result
Result Proceed to
Abnormal A
Normal B



A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY

B

24.PERFORM SIMULATION TEST
20.INSPECT FUEL INJECTOR ASSEMBLY
a.

Clean the inside of the surge tank with compressed air.


b.

After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

Result
Result Proceed to
400 ppm or higher A
Less than 400 ppm B

HINT:

If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.




A

21.INSPECT FUEL INJECTOR ASSEMBLY

B

22.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
21.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL INJECTOR>INSPECTION).

Result
Result Proceed to
Normal A
Abnormal B



A

22.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

B

REPLACE FUEL INJECTOR ASSEMBLY

22.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Check if carbon is in the air flow passage.

Result
Result Proceed to
No carbon present A
Carbon in passage B



A

23.CHECK INTAKE SYSTEM

B

CLEAN OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

23.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leak (See page Engine / Hybrid System>2NZ-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leak in intake system.




OK

24.PERFORM SIMULATION TEST

NG

REPAIR OR REPLACE INTAKE SYSTEM

24.PERFORM SIMULATION TEST
a.

Check if the engine can be started.

Result
Result Proceed to
Engine cannot be started A
Engine can be started B



A

25.CONFIRM PROBLEM SYMPTOM

B

END

25.CONFIRM PROBLEM SYMPTOM
a.

Confirm the problem symptoms.

HINT:

The problem symptoms below can be determined by reading the freeze frame data.


Result
Problem Symptom Suspected Area Proceed to
The engine does not crank
·

Battery fully depleted

·

Starter (includes pinion gear wear or tooth damage)

·

Starter system

·

Engine assembly (excess friction)

·

Drive plate wear or tooth damage*1

·

Flywheel wear or tooth damage*2


A
Abnormal cranking speed
·

Battery fully depleted

·

Starter assembly

·

Engine assembly (excess friction, compression loss)


B
There is no initial combustion (combustion does not occur even once)*3
·

Pressure regulator fuel pressure maintenance

·

Fuel injector leak

·

Fuel leak from fuel line

·

Fuel pump control circuit

·

Fuel pump

·

Spark plug

·

Crankshaft position sensor system

·

Ignition coil system


C
The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*4
·

Intake system connections

·

Throttle with motor body assembly

·

Camshaft timing oil control valve assembly

·

Mass air flow meter system


D
The initial combustion and starter turnoff occur late*5
·

Engine coolant temperature sensor

·

Mass air flow meter

·

Heated oxygen sensor (sensor 1)

·

Fuel injector assembly

·

Spark plug

·

Pressure regulator

·

Fuel pump

·

Fuel pump control circuit


E

*1: for Automatic Transaxle

*2: for Manual Transaxle

HINT:
·

If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter assembly may be malfunctioning.

·

*3: If there is no initial combustion, a wire harness may be malfunctioning, or the ignition or fuel system may be malfunctioning.

·

*4: If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the camshaft timing oil control valve assembly may have a problem returning.

·

*5: If the initial combustion and starter turnoff occur late, the fuel injection volume may be incorrect (too low or too high).





A

26.PERFORM SIMULATION TEST

B

32.PERFORM SIMULATION TEST

C

35.INSPECT FUEL INJECTOR ASSEMBLY

D

49.INSPECT MASS AIR FLOW METER

E

55.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
26.PERFORM SIMULATION TEST
a.

When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.

Result
Problem Symptom Suspected Area Proceed to
A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely.*3
·

Battery

·

Excess engine friction

·

Starter assembly


A
A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely.
·

Drive plate*1

·

Flywheel*2

·

Starter assembly


B
A noise indicating that the starter pinion gear is extending is not heard
·

Battery

·

Starter assembly

·

Starter system


C

*1: for Automatic Transaxle

*2: for Manual Transaxle

HINT:

*3: The battery may be fully depleted or there may be excess engine friction.




A

27.INSPECT BATTERY

B

29.INSPECT STARTER ASSEMBLY (STARTER PINION GEAR)

C

30.INSPECT BATTERY
27.INSPECT BATTERY

OK

28.CHECK ENGINE ASSEMBLY

NG

CHARGE OR REPLACE BATTERY

28.CHECK ENGINE ASSEMBLY
a.

Check that the crankshaft rotates smoothly when rotating it by hand.

OK:

Crankshaft rotates smoothly.


HINT:

Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.




OK

NG

REPAIR OR REPLACE ENGINE ASSEMBLY

29.INSPECT STARTER ASSEMBLY (STARTER PINION GEAR)
a.

b.

Check for starter pinion gear wear and damage.

OK:

There is no wear or damage.


Result
Result Proceed to
NG A
OK (for Automatic Transaxle) B
OK (for Manual Transaxle) C



A

REPLACE STARTER ASSEMBLY

B

REPLACE DRIVE PLATE AND GEAR SUB-ASSEMBLY

C

REPLACE FLYWHEEL SUB-ASSEMBLY

30.INSPECT BATTERY

OK

31.INSPECT STARTER ASSEMBLY

NG

CHARGE OR REPLACE BATTERY

31.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly (See page Engine / Hybrid System>2NZ-FE STARTING>STARTER>INSPECTION).



OK

NG

REPLACE STARTER ASSEMBLY

32.PERFORM SIMULATION TEST
a.

Check the cranking speed.

Result
Problem Symptom Suspected Area Proceed to
Cranking speed is slow (100 rpm or less)
·

Battery

·

Starter assembly

·

Excess engine friction


A
Cranking speed is fast (300 rpm or more)*1 Engine compression loss B

HINT:

*1: If the cranking speed is fast, there may be compression loss.




A

33.INSPECT BATTERY

B

CHECK AND REPAIR ENGINE ASSEMBLY

33.INSPECT BATTERY

OK

34.CHECK ENGINE ASSEMBLY

NG

CHARGE OR REPLACE BATTERY

34.CHECK ENGINE ASSEMBLY
a.

Check that the crankshaft rotates smoothly when rotating it by hand.

OK:

Crankshaft rotates smoothly.


HINT:

Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.




OK

NG

CHECK AND REPAIR ENGINE ASSEMBLY

35.INSPECT FUEL INJECTOR ASSEMBLY
a.

Using a sound scope or screwdriver, check for an injector operating sound while cranking the engine.

OK:

Fuel injector operating sound is heard.




OK

36.CHECK FUEL PRESSURE

NG

47.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
36.CHECK FUEL PRESSURE

OK

37.CHECK SPARK PLUG AND SPARK

NG

45.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
37.CHECK SPARK PLUG AND SPARK

OK

38.CONFIRM VEHICLE CONDITION

NG

41.INSPECT SPARK PLUG
38.CONFIRM VEHICLE CONDITION
a.

Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

Result
Problem Symptom Suspected Area Proceed to
When the engine is stopped and a long time has passed, engine starting trouble occurs*1 Pressure regulator is stuck open A
When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2 Fuel injector leak B
When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3 Failure to maintain fuel pressure by pressure regulator A
Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs - C*4

HINT:

*1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*2: Fuel may be leaking from a fuel injector assembly.

*3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*4: From step 69, perform fuel system troubleshooting C (steps 70 to 73).




A

39.CHECK FUEL PRESSURE

B

40.INSPECT FUEL INJECTOR ASSEMBLY

C

69.CHECK MALFUNCTION CONDITION
39.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

Standard:

147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)


HINT:

If the engine cannot be started, check the fuel pressure after cranking the engine.


Result
Result Proceed to
Abnormal A
Normal B*1

HINT:

*1: From step 69, perform fuel system troubleshooting C (steps 70 to 73).




A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY

B

69.CHECK MALFUNCTION CONDITION
40.INSPECT FUEL INJECTOR ASSEMBLY
a.

Clean the inside of the surge tank with compressed air.


b.

After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

Result
Result Proceed to
400 ppm or higher A
Less than 400 ppm B*1

HINT:
·

If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.

·

*1: From step 69, perform fuel system troubleshooting C (steps 70 to 73).





A

REPLACE FUEL INJECTOR ASSEMBLY

B

69.CHECK MALFUNCTION CONDITION
41.INSPECT SPARK PLUG

HINT:

Even if the spark plug of only one cylinder is malfunctioning, replace the spark plugs of all cylinders.



OK

42.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

NG

42.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


d.

Start the engine.


e.

While running the engine, read the value of Engine Speed.

OK:

A value that matches the actual engine speed is constantly output.


HINT:
·

Check the engine speed using a line graph.

·

If the engine cannot be started, check the engine speed while cranking the engine.

·

If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.





OK

43.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT

43.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)
a.

Check the harnesses and connectors, referring to DTC P0351 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0351).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

44.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)

NG

CHECK NO. 1 IGNITION COIL POWER SOURCE CIRCUIT

44.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)
a.

Check the harnesses and connectors, referring to DTC P0351 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0351).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

If the wire harness is normal, after replacing the No. 1 ignition coil, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 69 and perform troubleshooting for the ignition system (steps 74 to 79).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


d.

When performing the Active Test, check for an operating sound from the fuel pump.

OK:
Control the Fuel Pump/Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.




OK

46.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)

NG

46.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


d.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
Fuel leakage or signs of fuel leakage are present A
No fuel leakage or signs of fuel leakage B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.

·

If there are no fuel leaks, after inspecting the fuel pump control circuit, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 69 and perform fuel system troubleshooting C (steps 70 to 73).





A

REPAIR OR REPLACE FUEL LINE

B

47.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


d.

Start the engine.


e.

While running the engine, read the value of Engine Speed.

OK:

A value that matches the actual engine speed is constantly output.


HINT:
·

Check the engine speed using a line graph.

·

If the engine cannot be started, check the engine speed while cranking the engine.

·

If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.





OK

48.CHECK TERMINAL VOLTAGE (FUEL INJECTOR CIRCUIT)

NG

48.CHECK TERMINAL VOLTAGE (FUEL INJECTOR CIRCUIT)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0300).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

NG

49.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0171).



OK

50.CHECK INTAKE SYSTEM

NG

54.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
50.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system (vacuum hose disconnection, cracks, damaged gaskets, etc.) (See page Engine / Hybrid System>2NZ-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.

·

If Short FT #1 and Long FT #1 are largely different from the normal values (differ by more than 15%) when idling (intake air volume is small) and almost the same as the normal values when racing the engine (for example, when maintaining a speed of 3000 rpm) (intake air volume is high), air leakage may be present.



OK:

There is no air leakage.




OK

51.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

NG

REPAIR OR REPLACE INTAKE SYSTEM

51.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Disconnect the throttle with motor body assembly connector.

HINT:

When the connector is disconnected, the vehicle enters fail-safe mode and the throttle valve opening angle is 4 to 7°.



b.

Crank the engine and check that it starts.

Result
Result Proceed to
Engine starts A
Engine does not start B


c.

Connect the throttle with motor body assembly connector.

HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).




A

52.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

B

53.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
52.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Check if carbon is in the air flow passage.

OK:

No carbon present.




OK

53.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)

NG

REMOVE FOREIGN OBJECT AND CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY

53.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
a.

Performing the Active Test, referring to DTC P0011 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0011).

Result
Result Proceed to
NG A
OK B*1

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

*1: From step 69, perform intake system troubleshooting (steps 80 to 82). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 83 to 90).





A

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

B

69.CHECK MALFUNCTION CONDITION
54.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Check the harnesses and connectors, referring to DTC P0100 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0100).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

If the wire harness is normal, after replacing the mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 69 and perform intake system troubleshooting (steps 80 to 82). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 83 to 90).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).

HINT:

If the engine coolant temperature sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.




OK

56.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG

56.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0115 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0115).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.




OK

57.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

57.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0171).


HINT:

If the mass air flow meter is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



OK

58.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

58.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Check the harnesses and connectors, referring to DTC P0100 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0100).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.




OK

59.READ VALUE USING INTELLIGENT TESTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

59.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT and Atmosphere Pressure.

Result
Data List Item Result Suspected Area Proceed to
Long FT #1 +25% or more or less than -25%
·

Heated oxygen sensor (sensor 1)

·

Mass air flow meter

·

Fuel injector assembly

·

ECM


A
Atmosphere Pressure 80 kPa or less (when altitude is 0 m)
Both Data List items listed above Values are other than above - B



A

60.PERFORM SIMULATION TEST

B

63.CHECK FUEL PRESSURE
60.PERFORM SIMULATION TEST
a.

Remove the EFI MAIN and ETCS fuses from the engine room relay block.


b.

After 60 seconds or more elapse, install the EFI MAIN and ETCS fuses.


c.

Check if the engine can be started.

Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

61.INSPECT HEATED OXYGEN SENSOR

B

63.CHECK FUEL PRESSURE
61.INSPECT HEATED OXYGEN SENSOR
A257483E01
0.531,0.376 1.618,0.539 1.086,0.163 10 Injection Volume 1.021,0.826 1.517,0.975 0.496,0.149 10 +12% 1.056,1.169 1.541,1.307 0.486,0.139 10 -12% 0.202,1.863 2.655,2.046 2.453,0.184 10 Heated Oxygen Sensor Output Voltage 0.256,2.384 1.461,2.533 1.205,0.149 10 Higher than 0.5 V 0.677,2.776 1.458,2.918 0.781,0.142 10 Below 0.4 V 3.008,2.586 3.270,2.725 0.261,0.139 10 OK

a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel System Status #1.


e.

Confirm that Fuel System Status #1 is CL.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.


g.

Read the output voltage from the heated oxygen sensors when increasing and decreasing the fuel injection volume.

Standard:
Tester Display Injection Volume Specified Condition
O2S B1S1 +12% Heated oxygen sensor (sensor 1) output voltage is higher than 0.5 V
-12% Heated oxygen sensor (sensor 1) output voltage is below 0.4 V


Result
Result Proceed to
Normal A
Abnormal B

HINT:
·

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the heated oxygen sensor (sensor 1) is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.





A

62.PERFORM SIMULATION TEST

B

62.PERFORM SIMULATION TEST
a.

Check if the idling speed is stable after starting the engine.

OK:

Engine speed is stable.


HINT:

After replacing the fuel injector assembly or mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.




OK

NG

REPLACE FUEL INJECTOR ASSEMBLY

63.CHECK FUEL PRESSURE

OK

64.INSPECT SPARK PLUG

NG

68.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
64.INSPECT SPARK PLUG
a.

Inspect the spark plugs (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

Result
Result Proceed to
All cylinders are normal A
One cylinder is abnormal*1 B
All cylinders are abnormal*2, *3 C


HINT:
·

*1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.

·

*2: If all cylinders are abnormal, replace the spark plugs of all cylinders and check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.

·

*3: Engine starting trouble may occur if the vehicle is driven extremely short distances repeatedly.




A

65.CONFIRM VEHICLE CONDITION

B

C

65.CONFIRM VEHICLE CONDITION
a.

Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

Result
Problem Symptom Suspected Area Proceed to
When the engine is stopped and a long time has passed, engine starting trouble occurs*1 Pressure regulator is stuck open A
When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2 Fuel injector leak B
When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3 Failure to maintain fuel pressure by pressure regulator A
Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs - C*4

HINT:

*1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*2: Fuel may be leaking from a fuel injector assembly.

*3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*4: From step 69, perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.




A

66.CHECK FUEL PRESSURE

B

67.INSPECT FUEL INJECTOR ASSEMBLY

C

69.CHECK MALFUNCTION CONDITION
66.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

Standard:

147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)


HINT:

If the engine cannot be started, read the values after cranking the engine.


Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

If the engine cannot be started, check the fuel pressure after cranking the engine.

·

*1: From step 69, perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.





A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY

B

69.CHECK MALFUNCTION CONDITION
67.INSPECT FUEL INJECTOR ASSEMBLY
a.

Clean the inside of the surge tank with compressed air.


b.

After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

Result
Result Proceed to
400 ppm or higher A
Less than 400 ppm B*1

HINT:
·

If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.

·

*1: From step 69, perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.





A

REPLACE FUEL INJECTOR ASSEMBLY

B

69.CHECK MALFUNCTION CONDITION
68.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


d.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
Fuel leakage or signs of fuel leakage are present A
No fuel leakage or signs of fuel leakage B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.

·

If there are no fuel leaks, after inspecting the fuel pump control circuit, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.





A

REPAIR OR REPLACE FUEL LINE

B

69.CHECK MALFUNCTION CONDITION
a.

If the malfunction could not be identified during the inspection in steps 38, 39, 40 and 46, perform fuel system troubleshooting C (steps 70 to 73).

Result
Performed Step Troubleshooting by System Procedure Proceed to
Steps 38, 39, 40 and 46 Fuel system troubleshooting C 70 to 73 A


b.

If the malfunction could not be identified during the inspection in step 44, perform ignition system troubleshooting (steps 74 to 79).

Result
Performed Step Troubleshooting by System Procedure Proceed to
Step 44 Ignition system troubleshooting 74 to 79 B


c.

If the malfunction could not be identified during the inspection in steps 53 and 54, perform intake air system troubleshooting (steps 80 to 82). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 83 to 90).

Result
Performed Step Troubleshooting by System Procedure Proceed to
Step 53 and 54 Intake air system troubleshooting 80 to 82 C
Fuel system troubleshooting A 83 to 90


d.

If the malfunction could not be identified during the inspection in steps 55, 56, 57, 58, 61, 62, 64, 65, 66, 67 and 68, perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake air system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.

Result
Performed Step Troubleshooting by System Procedure Proceed to
Steps 55, 56, 57, 58, 61, 62, 64, 65, 66, 67 and 68 Fuel system troubleshooting A 91 to 98 D
Fuel system troubleshooting B 99 to 101
Intake air system troubleshooting 102 to 104
Ignition system troubleshooting 105 to 110



A

70.INSPECT FUEL INJECTOR ASSEMBLY

B

74.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

C

80.READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE)

D

91.CHECK FUEL PRESSURE
70.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL INJECTOR>INSPECTION).



OK

71.CHECK TERMINAL VOLTAGE (FUEL INJECTOR CIRCUIT)

NG

REPLACE FUEL INJECTOR ASSEMBLY

71.CHECK TERMINAL VOLTAGE (FUEL INJECTOR CIRCUIT)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0300).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

72.CHECK CRANKSHAFT POSITION SENSOR

NG

72.CHECK CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

73.CHECK CAMSHAFT POSITION SENSOR
73.CHECK CAMSHAFT POSITION SENSOR
a.

b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)

NG

74.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

75.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

75.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.

Check the tightening and installation condition of the camshaft position sensor bolt.


b.

Check the connection of the camshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

76.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

76.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0335 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0335).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

77.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

77.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0340 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0340).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

78.CHECK CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

78.CHECK CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

79.CHECK CAMSHAFT POSITION SENSOR
79.CHECK CAMSHAFT POSITION SENSOR
a.

b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)

NG

80.READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches should be off.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

Result
Data List Item Result Suspected Area Proceed to
ISC Learning Value (engine displacement (liters) x 0.9) or more
·

Valve timing

·

Compression


A
Less than (engine displacement (liters) x 0.9) - B



A

81.CHECK CYLINDER COMPRESSION PRESSURE

B

82.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
81.CHECK CYLINDER COMPRESSION PRESSURE

OK

NG

CHECK AND REPAIR ENGINE ASSEMBLY

82.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL).



OK

83.CHECK FUEL PRESSURE

NG

83.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.

Standard:
Vehicle State Specified Condition
Cranking engine 304 to 343 kPa (3.1 to 3.5 kgf/cm2)
5 minutes after stopping engine 147 kPa (1.5 kgf/cm2) or more




OK

84.READ VALUE USING INTELLIGENT TESTER (LONG FT #1)

NG

89.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
84.READ VALUE USING INTELLIGENT TESTER (LONG FT #1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1.

Result
Data List Item Result Suspected Area Proceed to
Long FT #1 -15 to +15%
·

Wire harness or connector

·

Fuel


A
+15% or more, or less than -15% Fuel injector assembly B



A

85.PERFORM SIMULATION TEST

B

REPLACE FUEL INJECTOR ASSEMBLY

85.PERFORM SIMULATION TEST
a.

Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

Result
Problem Symptom Suspected Area Proceed to
Current unstable idling speed or history of unstable idling speed Crankshaft position sensor system A
All current and past idling speeds are stable Fuel B

HINT:

Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.




A

86.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

B

REPLACE FUEL

86.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

87.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

87.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0335 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0335).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

88.CHECK CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

88.CHECK CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

89.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


d.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
Fuel leakage or signs of fuel leakage are present A
No fuel leakage or signs of fuel leakage B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.





A

REPAIR OR REPLACE FUEL LINE

B

90.INSPECT FUEL PUMP
90.INSPECT FUEL PUMP
a.

Inspect the fuel pump (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL PUMP>INSPECTION).

HINT:
·

Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.

·

Make sure the internal connector is securely connected.

·

Make sure the fuel pump filter is not clogged.





OK

REPLACE FUEL PRESSURE REGULATOR

NG

91.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

Standard:

147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)


HINT:

If the engine cannot be started, read the values after cranking the engine.


Result
Result Proceed to
Normal A
Abnormal B



A

92.READ VALUE USING INTELLIGENT TESTER (LONG FT #1)

B

97.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
92.READ VALUE USING INTELLIGENT TESTER (LONG FT #1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1.

Result
Data List Item Result Suspected Area Proceed to
Long FT #1 -15 to +15%
·

Wire harness or connector

·

Fuel


A
+15% or more, or less than -15% Fuel injector assembly B



A

93.PERFORM SIMULATION TEST

B

REPLACE FUEL INJECTOR ASSEMBLY

93.PERFORM SIMULATION TEST
a.

Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

Result
Problem Symptom Suspected Area Proceed to
Current unstable idling speed or history of unstable idling speed Crankshaft position sensor system A
All current and past idling speeds are stable Fuel B

HINT:

Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.




A

94.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

B

REPLACE FUEL

94.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

95.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

95.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0335 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0335).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

96.CHECK CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

96.CHECK CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

97.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


d.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
No fuel leakage or signs of fuel leakage A
Fuel leakage or signs of fuel leakage are present B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.





A

98.INSPECT FUEL PUMP

B

REPAIR OR REPLACE FUEL LINE

98.INSPECT FUEL PUMP
a.

Inspect the fuel pump (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL PUMP>INSPECTION).

HINT:
·

Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.

·

Make sure the internal connector is securely connected.

·

Make sure the fuel pump filter is not clogged.





OK

99.CHECK PURGE VSV

NG

99.CHECK PURGE VSV
a.
A258724E02
0.595,0.098 0.760,0.242 0.165,0.144 10 *2 2.649,0.912 2.822,1.060 0.174,0.148 10 *1 0.77,1.554 0.925,1.713 0.155,0.159 10 *3 0.956,1.609 1.356,1.092 false 2.374,0.741 2.637,0.97 false 0.784,0.191 1.388,0.346 false

Disconnect the vacuum hose (on the canister side) of the purge VSV.

Text in Illustration
*1 Hose (to Canister)
*2 Connector
*3 Purge VSV


b.

Start the engine.


c.

Idle the engine.


d.

Disconnect the connector of the purge VSV.


e.

Check if air flows through the purge VSV.

OK:

Air Does not flow



f.

Reconnect the connector of the purge VSV.


g.

Reconnect the vacuum hose of the purge VSV.

HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).




OK

100.CHECK FUEL INJECTOR ASSEMBLY

NG

100.CHECK FUEL INJECTOR ASSEMBLY
a.

Clean the inside of the surge tank with compressed air.


b.

After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

Result
Result Proceed to
400 ppm or higher A
Less than 400 ppm B

HINT:

If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.




A

REPLACE FUEL INJECTOR ASSEMBLY

B

101.CHECK INTAKE VALVE
101.CHECK INTAKE VALVE
a.

Check if carbon is on the intake valves.

Result
Result Proceed to
Carbon present A
No carbon present B



A

CLEAN INTAKE VALVE

B

102.READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE)
102.READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

Result
Data List Item Result Suspected Area Proceed to
ISC Learning Value (engine displacement (liters) x 0.9) or more
·

Valve timing

·

Compression


A
Less than (engine displacement (liters) x 0.9) - B



A

103.CHECK CYLINDER COMPRESSION PRESSURE

B

104.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
103.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (See page Engine / Hybrid System>2NZ-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).



OK

NG

CHECK AND REPAIR ENGINE ASSEMBLY

104.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).



OK

105.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

105.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

106.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

106.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.

Check the tightening and installation condition of the camshaft position sensor bolt.


b.

Check the connection of the camshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

107.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

107.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0335 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0335).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

108.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

108.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0340 inspection procedure (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0340).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

109.CHECK CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

109.CHECK CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

110.CHECK CAMSHAFT POSITION SENSOR
110.CHECK CAMSHAFT POSITION SENSOR
a.

b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)

NG