Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected


DESCRIPTION

A093767E03
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold level, and could cause emission deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
  1. A misfire occurs that may damage the three-way catalytic converter (MIL brinks when detect immediately).
  2. An emission deterioration misfire occurs (MIL illuminates).
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel injector assembly
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV valve and hose
  13. PCV hose connections
  14. Intake system
  15. ECM
P0301
P0302
P0303
P0304
Misfiring of specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
  1. A misfire occurs that may damage the three-way catalytic converter (MIL brinks when detect immediately).
  2. An emission deterioration misfire occurs (MIL illuminates).
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION


  1. The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
    1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 500 misfires per 1000 crankshaft revolutions) occurs once.
    2. An excessive misfiring rate (approximately 250 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
    The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when the following condition, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected.
    1. A catalyst damaged misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.

MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
Required Sensors/Components (Main)
Crankshaft position sensor and Camshaft position sensor
Required Sensors/Components (Related)
Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation
Continuous
Duration
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation
2 driving cycles: Emission-related misfire
MIL flashes immediately: Catalyst-damaged misfire
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire: 
Monitor runs whenever following DTCs not present
P0016 (VVT system - misalignment)
P0102 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
P0120 - P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for Closed Loop)
P0327, P0328 (Knock sensor)
P0335 (CKP sensor)
P0340 (VVT sensor)
P0351 - P0354 (Igniter)
P0500 (VSS)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine RPM
450 to 6600 rpm
ECT
More than 65°C (149°F)
Fuel cut
OFF

Monitor period of emission-related misfire: 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above (MIL blinks immediately)
Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damaged misfire (MIL blinks): 
All of following conditions 1, 2 and 3 met
Crankshaft 200 revolutions x 3
1. Driving cycles
1st
2. Check mode
OFF
Except above
Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS


Monitor period of emission-related misfire: 
Misfire rate
50% or more: for 1st 1000 revolutions
25% or more: after 1st 1000 revolutions

Monitor period of catalyst-damaged misfire (MIL blinks): 
Number of misfire per 200 revolutions
101 or more (varies with intake air amount and rpm)

WIRING DIAGRAM


A239471E01


A257829E01


CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Record the DTC(s) and freeze frame data.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  6. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
  8. Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    1. In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.

    Engine RPM
    Duration
    Idling
    8.0 minutes or more
    1000
    4.5 minutes or more
    2000
    2.5 minutes or more
    3000
    1.5 minutes or more

  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be erased.

  10. Record the DTC(s), freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 30 seconds.
  12. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, the following factors are possible causes of the problem:
    1. There is insufficient fuel in the tank.
    2. Improper fuel is used.
    3. The spark plugs are contaminated.
    4. The problem requires further diagnosis.
  5. After finishing repairs, check the misfire counts of the cylinders Cylinder #1 Misfire Count to Cylinder #4 Misfire Count.
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
  7. When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be Rich (-20% or less) or Lean (+20% or more).
  8. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.
  9. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P0300, P0301, P0302, P0303 and/or P0304 are output
    A
    DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connection (Click here).

OK:
PCV valve and hose are connected correctly and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4.READ VALUE USING TECHSTREAM (CATALYST OT MF F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.
    Result 
    Data List
    Techstream Display
    Proceed to
    Catalyst OT MF F/C
    Avail
    A
    Not Avl
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM (PROHIBIT CAT OT F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.


NEXT


6.READ VALUE USING TECHSTREAM (CYLINDER #1 MISFIRE COUNT, #2, #3 AND #4)
  1. Enter the following menus: Powertrain / Engine / Data List / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.

  1. Start the engine and allow the engine to idle.

  1. Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the Techstream. If no misfire counts occur in any cylinders, perform following steps and then check the misfire counts again.

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above.

  1. Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the Techstream.
    Result 
    Result
    Proceed To
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

HINT:
  1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
  2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
  3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 17
A


7.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG
OK


8.CHECK FOR SPARKS AND IGNITION
  1. Perform a spark test .



NG
Go to step 32
OK


9.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
A238664E01
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the ECM connector.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    #10 (C20-108) - E01 (C20-45)
    Ignition Switch ON
    11 to 14 V
    #20 (C20-107) - E01 (C20-45)
    Ignition Switch ON
    11 to 14 V
    #30 (C20-106) - E01 (C20-45)
    Ignition Switch ON
    11 to 14 V
    #40 (C20-105) - E01 (C20-45)
    Ignition Switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


11.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


12.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak.

    OK:
    No leak from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


13.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 34
OK


14.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 80 and 100°C (176 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


15.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 2500 rpm.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: Off
    Engine Speed: 2500 rpm
    Between 2 gm/sec, and 6 gm/sec.



NG
Go to step 27
OK


16.CHECK VALVE TIMING


    A175434E02
  1. Remove the cylinder head cover.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.

  1. Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *a
    Timing Mark

  1. Reinstall the cylinder head cover.



OK
Go to step 27

NG
ADJUST VALVE TIMING (Click here)

17.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak.

    OK:
    No leak from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


18.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 34
OK


19.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 80 and 100°C (176 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


20.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 2500 rpm.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: Off
    Engine Speed: 2500 rpm
    Between 2 gm/sec, and 6 gm/sec.



NG
Go to step 27
OK


21.CHECK VALVE TIMING


    A175434E02
  1. Remove the cylinder head cover.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.

  1. Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *a
    Timing Mark

  1. Reinstall the cylinder head cover.



NG
ADJUST VALVE TIMING (Click here)
OK


22.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG
OK


23.CHECK FOR SPARKS AND IGNITION
  1. Perform a spark test .



NG
Go to step 32
OK


24.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


25.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
A238664E01
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the ECM connector.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    #10 (C20-108) - E01 (C20-45)
    Ignition Switch ON
    11 to 14 V
    #20 (C20-107) - E01 (C20-45)
    Ignition Switch ON
    11 to 14 V
    #30 (C20-106) - E01 (C20-45)
    Ignition Switch ON
    11 to 14 V
    #40 (C20-105) - E01 (C20-45)
    Ignition Switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


26.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


27.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


28.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303 or P0304.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    ABNORMAL (P0300, P0301, P0302, P0303 or P0304 output)
    A
    NORMAL (No DTC output)
    B



B
END
A


29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the C26 mass air flow meter connector.

  1. Disconnect the C20 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C26-3 (VG) - C20-118 (VG)
    Always
    Below 1 Ω
    C26-2 (E2G) - C20-116 (E2G)

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C26-3 (VG) or C20-118 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


30.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    If the results of the inspections performed in steps 15 and 20 indicated no problem, proceed to the next step without replacing the mass air flow meter.


NEXT


31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303 or P0304.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    NORMAL (No DTC output)
    A
    ABNORMAL (P0300, P0301, P0302, P0303 or P0304 output)
    B



B
REPLACE ECM
A

END 

32.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all fuel injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug into the ignition coil No. 1 and connect the ignition coil connector.

    2. Disconnect the fuel injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 33
OK

REPLACE SPARK PLUG 

33.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the ignition coil No. 1 to an ignition coil No. 1 that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all fuel injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug into the ignition coil No. 1 and connect the ignition coil connector.

    2. Disconnect the fuel injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL NO.1 (Click here)  

34.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)