Home › Engine / Hybrid System › 1NR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.04
RM30M0E _51 Engine / Hybrid System _053932 1NR-FE ENGINE MECHANICAL _0262434 ENGINE UNIT A

1NR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the camshaft or No. 2 camshaft or camshaft timing gear assembly or camshaft timing exhaust gear assembly or engine coolant temperature sensor or knock sensor or spark plug.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


a.
A312300E02
0.302,1.979 2.75,2.198 2.448,0.219 10 false 7.988 to 8.0 mm 1.219,2.813 2.677,3.198 1.458,0.385 10 false 18.0 mm (0.709 in.) 1.854,3.365 3.229,3.74 1.375,0.375 10 false 8.0 to 10.0 mm 0.302,2.156 2.75,2.375 2.448,0.219 10 false (0.3145 to 0.3149 in.) 1.844,3.531 3.219,3.906 1.375,0.375 10 false (0.315 to 0.394 in.)

Using a plastic hammer, tap in 2 new straight pins to the specified protrusion height.

Protrusion height:

8.0 to 10.0 mm (0.315 to 0.394 in.)



Hide 2.INSTALL RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A312302E02
2.031,3.563 3.313,3.75 1.281,0.188 10 false 2.7 to 3.3 mm 1.458,3.042 2.74,3.229 1.281,0.188 10 false 8.0 mm (0.3150 in.) 0.323,2.313 1.99,2.729 1.667,0.417 10 false 12.482 to 12.5 mm 0.323,2.49 1.99,2.906 1.667,0.417 10 false (0.4914 to 0.4921 in.) 2.01,3.74 3.26,4.083 1.25,0.344 10 false (0.106 to 0.130 in.)

Using a plastic hammer, tap in 10 new ring pins to the specified protrusion height.

Protrusion height:

2.7 to 3.3 mm (0.106 to 0.130 in.)



Hide 15104 3.INSTALL OIL STRAINER SUB-ASSEMBLY

a.
A313188

Apply a light coat of engine oil to a new oil strainer O-ring.


b.

Install the oil strainer O-ring to the oil strainer sub-assembly.

NOTICE:

Do not twist the oil strainer O-ring.



c.
A313189

Install the oil strainer sub-assembly to the oil pan sub-assembly.

NOTICE:

Do not twist the oil strainer O-ring.



Hide 12121 4.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.
A320643

Install the No. 1 oil pan baffle plate to the oil pan sub-assembly with the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12122 5.INSTALL NO. 2 OIL PAN BAFFLE PLATE

a.
A320642

Install the No. 2 oil pan baffle plate to the oil pan sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12101 6.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old packing material from the contact surface.


b.
A312389

Install a new oil pan O-ring to the cylinder block sub-assembly.


c.

Apply seal packing to the places shown in the illustration.

A312362C01
5.01,0.427 5.323,0.583 0.313,0.156 10 false *a 5.031,2.208 5.344,2.365 0.313,0.156 10 false *b 2.99,0.208 4.229,0.427 1.24,0.219 10 false 33.9 mm (1.334 in.) 5.542,2.208 6.948,2.573 1.406,0.365 10 false 6.0 to 10.0 mm (0.236 to 0.394 in.) 4.229,3 5.563,3.375 1.333,0.375 10 false 3.5 to 4.5 mm (0.138 to 0.177 in.) 5.521,0.438 6.854,0.813 1.333,0.375 10 false 3.5 to 4.5 mm (0.138 to 0.177 in.) 1.719,3.49 2.021,3.688 0.302,0.198 10 false 90°
*a Continuous Line Area *b Dashed Line Area


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




d.

Clean and degrease the threads of the bolt (C) and threaded portion of the cylinder block sub-assembly.


e.
A300629C01
1.667,1.448 1.51,0.813 true 1.323,0.708 1.635,0.865 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to the threads of the bolt (C).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.


HINT:

Apply adhesive to the bolt (C) more than 7.0 mm (0.276 in.) from the bolt end.



f.
A313199C03
0.969,0.104 1.438,0.313 0.469,0.208 10 false 11 (B) 0.354,0.51 0.823,0.719 0.469,0.208 10 false 10 (A) 1.49,0.031 2.344,0.219 0.854,0.188 10 false 2 (*a), 12(B) 2.375,0.146 2.74,0.344 0.365,0.198 10 true 3 (B) 2.865,0.51 3.229,0.708 0.365,0.198 10 false 4 (A) 2.854,1.469 3.219,1.667 0.365,0.198 10 false 5 (A) 2.302,1.844 2.667,2.042 0.365,0.198 10 true 6 (B) 1.365,1.917 2.146,2.156 0.781,0.24 10 false 1 (*a), 7(B) 0.865,1.885 1.229,2.083 0.365,0.198 10 false 8 (B) 0.313,1.635 0.677,1.833 0.365,0.198 10 false 9 (C)
*a Temporarily Tighten


Install the oil pan sub-assembly to the cylinder block sub-assembly with the 10 bolts, in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Bolt Length:
Item Length
Bolt A 70 mm (2.756 in.)
Bolt B, C 30 mm (1.181 in.)



g.

Wipe off any excess seal packing with a clean piece of cloth.


Hide 12101A 7.INSTALL OIL PAN DRAIN PLUG

a.
A312386

Install a new gasket and oil pan drain plug to the oil pan sub-assembly.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 8.INSTALL OIL FILTER UNION

a.
A243541

Using a 12 mm socket hexagon wrench, install the oil filter union to the oil pan sub-assembly.

Torque:
33.7 N*m (344 kgf*cm, 25 ft.*lbf)


Hide 15601 9.INSTALL OIL FILTER SUB-ASSEMBLY

Hide 11445 11.INSTALL CYLINDER BLOCK WATER JACKET SPACER

a.
A312363

Install the cylinder block water jacket spacer to the cylinder block sub-assembly.


Hide 11101 13.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13750 14.INSTALL VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free of dirt and foreign matter.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.


b.
A286731C05
1.094,0.75 1.573,0.479 true 1.948,0.49 2.417,0.698 true 1,1.198 1.615,0.917 true 1.885,0.938 2.521,1.094 true 1.021,1.448 1.615,1.313 true 1.885,1.313 2.469,1.417 true 0.896,1.844 1.625,1.781 true 1.885,1.781 2.573,1.875 true 0.802,2.313 1.635,2.5 true 1.917,2.5 2.698,2.281 true 0.781,2.771 0.781,2.49 true 2.698,2.76 2.698,2.479 true 1.333,3.333 1.521,2.844 true 1.677,1.219 1.99,1.375 0.313,0.156 10 *1 1.719,2.448 2.031,2.604 0.313,0.156 10 *2 1.688,1.708 2,1.865 0.313,0.156 10 *d 0.729,2.792 1.042,2.948 0.313,0.156 10 *e 0.688,0.229 1,0.385 0.313,0.156 10 *a 2.635,0.229 2.948,0.385 0.313,0.156 10 *b 1.677,0.844 1.99,1 0.313,0.156 10 *c 1.563,2.75 2.021,2.948 0.458,0.198 10 SST 1.625,0.396 2.083,0.594 0.458,0.198 10 SST 2.635,2.792 2.948,2.99 0.313,0.198 10 *e
*1 Plunger
*2 Check Ball
*a Correct
*b Incorrect
*c Taper Part
*d Low Pressure Chamber
*e High Pressure Chamber


Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed it.

OK:

Plunger moves up and down.


NOTICE:

When bleeding the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, the high-pressure chamber will not be bled.



e.

After bleeding, remove SST. Then, try to press the plunger quickly and firmly by hand.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


f.

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install each valve lash adjuster assembly to the same place it was removed from.



Hide 13801 15.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply engine oil to the valve lash adjuster assembly tip and valve stem cap end.


b.
A131901C32
1.104,1.24 0.729,1.24 false 1.729,0.458 1.5,0.323 false 2.656,0.646 2.156,0.802 true 2.708,1.302 2.063,0.875 true 1.313,0.219 2.469,0.542 1.156,0.323 10 false *1 2.75,1.208 3.021,1.375 0.271,0.167 10 false *3 2.688,0.531 3.135,0.896 0.448,0.365 10 false *4 0.563,1.177 1.104,1.5 0.542,0.323 10 false *2
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve
*4 Valve Stem Cap


Make sure that the 16 No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


c.
A313191

Fill the cylinder head sub-assembly with engine oil through the holes indicated in the illustration.


Hide 11103 19.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13070A 20.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 21.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 22.INSTALL CRANKSHAFT STRAIGHT PIN

a.
A313192

Install the crankshaft straight pin into the crankshaft groove.


Hide 23.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A313193C01
0.354,1.396 0.281,0.969 true 0.156,0.771 0.469,0.969 0.313,0.198 10 false *a
*a Groove


Align the groove of the crankshaft timing sprocket with the key of the crankshaft and install the crankshaft timing sprocket.


Hide 13566B 24.INSTALL TIMING CHAIN GUIDE

Hide 13506 25.INSTALL CHAIN SUB-ASSEMBLY

Hide 13591 26.INSTALL TIMING CHAIN TENSION ARM

Hide 13540 27.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11302A 28.INSTALL TIMING CHAIN COVER OIL SEAL

Hide 11310 30.INSTALL TIMING CHAIN COVER ASSEMBLY

a.

Remove any old seal packing material from the contact surface.


b.
A381453

Temporarily install a new water pump gasket and engine water pump assembly to the timing chain cover assembly with the 4 bolts.

Bolt Length:

20 mm (0.787 in.)



c.

Clean the contact surfaces of the timing chain cover assembly, camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.

A381454C01
0,0 0,0 false
V100144

Surface to be cleaned - -



d.
A381452

Install 3 new oil pump O-rings to the oil pan sub-assembly.


e.

Apply seal packing to the timing chain cover assembly as shown in the following illustration.

A381455C01
2.51,1.073 3.625,0.219 3.625,0.219 3.281,1.635 true 1.865,2.802 2.781,2.802 true 3.49,1.729 4.25,0.333 true 2.24,1.583 2.396,1.781 0.156,0.198 10 false A 3.177,2.323 3.333,2.521 0.156,0.198 10 true B 4.375,1.646 4.531,1.844 0.156,0.198 10 true A 5,1.448 5.156,1.646 0.156,0.198 10 false A 5.583,1.26 6.24,1.677 0.656,0.417 10 false 17.5 mm 6.333,1.438 6.99,1.854 0.656,0.417 10 false 323.5 mm 4.313,0.229 5.646,0.479 1.333,0.25 10 false 19.5 mm (0.768 in.) 3.698,0.073 3.938,0.271 0.24,0.198 10 false *a 2.563,2.573 2.719,2.771 0.156,0.198 10 true B 3.833,2.469 3.99,2.667 0.156,0.198 10 true B 4.479,2.458 4.635,2.656 0.156,0.198 10 false B 5.583,2.167 6.229,2.594 0.646,0.427 10 false 12.0 mm 6.354,3.063 7.01,3.479 0.656,0.417 10 false 221.0 mm 6.438,4.167 7.104,4.583 0.667,0.417 10 false 17.0 mm 1.667,2.708 1.906,2.906 0.24,0.198 10 false *b 1.125,1.198 1.781,1.615 0.656,0.417 10 false 23.0 mm 0.219,1.417 0.875,1.833 0.656,0.417 10 false 328.5 mm 1.156,2.177 1.813,2.594 0.656,0.417 10 false 18.5 mm 0.208,3.042 0.865,3.458 0.656,0.417 10 false 225.5 mm 1.042,4.396 1.698,4.813 0.656,0.417 10 false 14.0 mm 0.229,4.156 0.885,4.573 0.656,0.417 10 false 18.0 mm 2.219,4.375 2.375,4.573 0.156,0.198 10 false A 2.875,1.438 3.031,1.635 0.156,0.198 10 false A 2.823,4.563 2.979,4.76 0.156,0.198 10 true A 4.219,4.417 4.375,4.615 0.156,0.198 10 true A 4.875,4.521 5.031,4.719 0.156,0.198 10 false A 5.563,4.365 6.188,4.76 0.625,0.396 10 false 12.0 mm 0.385,5.188 0.729,5.438 0.344,0.25 10 false A-A 3.885,5.208 4.229,5.458 0.344,0.25 10 false B-B 0.792,5.604 2.948,5.802 2.156,0.198 10 false (0.157 to 0.315 in.) 0.813,5.438 2.969,5.635 2.156,0.198 10 false 4.0 to 8.0 mm 4.25,5.417 6.406,5.615 2.156,0.198 10 false 13.0 to 15.0 mm 4.26,5.583 5.479,5.771 1.219,0.188 10 false (0.512 to 0.591 in.) 5.844,6.49 6.969,6.667 1.125,0.177 10 false 3.5 to 4.5 mm 5.833,6.667 7.052,6.854 1.219,0.188 10 false (0138 to 0.177 in.) 1.948,6.396 3.073,6.573 1.125,0.177 10 false 3.5 to 4.5 mm 1.938,6.583 3.156,6.771 1.219,0.188 10 false (0138 to 0.177 in.) 0.354,6.063 1.563,6.25 1.208,0.188 10 false 3.5 mm 0.333,6.229 1.552,6.438 1.219,0.208 10 false (0.138 in.) 3.552,6.167 4.76,6.354 1.208,0.188 10 false 7.0 mm 3.542,6.333 4.76,6.542 1.219,0.208 10 false (0.276 in.) 5.594,1.417 6.25,1.833 0.656,0.417 10 false (0.689 in.) 5.583,2.323 6.229,2.75 0.646,0.427 10 false (0.472 in.) 1.104,1.365 1.76,1.781 0.656,0.417 10 false (0.906 in.) 1.156,2.344 1.813,2.76 0.656,0.417 10 false (0.728 in.) 6.344,1.594 7,2.01 0.656,0.417 10 false (1.061 ft.) 6.354,3.24 7.01,3.656 0.656,0.417 10 false (8.701 in.) 6.438,4.333 7.104,4.75 0.667,0.417 10 false (0.669 in.) 5.573,4.521 6.198,4.917 0.625,0.396 10 false (0.472 in.) 1.031,4.552 1.688,4.969 0.656,0.417 10 false (0.551 in.) 0.198,1.583 0.854,2 0.656,0.417 10 false (1.077 ft.) 0.198,3.198 0.854,3.615 0.656,0.417 10 false (8.878 in.) 0.229,4.323 0.885,4.74 0.656,0.417 10 false (0.709 in.)
*a Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent *b Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


NOTICE:
·

If there is oil on the contact surfaces, wipe them with oil-free cloth before applying seal packing.

·

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.



HINT:

Areas A-A and B-B are the joints between the cylinder block sub-assembly and oil pan sub-assembly, cylinder block sub-assembly and cylinder head sub-assembly, and cylinder head sub-assembly and camshaft housing sub-assembly.


Seal Packing Specification:
Area Seal Packing Diameter Seal packing
Continuous Line Area
Except A-A and B-B
3.5 to 4.5 mm (0.138 to 0.177 in.) Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Dashed Line Area 3.5 to 4.5 mm (0138 to 0.177 in.) Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent



f.

Align the oil pump drive rotor spline and crankshaft as shown in the illustration, and install the timing chain cover assembly to the crankshaft.

A381456


g.
A381457C03
1.729,1.594 1.75,1.74 true 0.792,0.188 0.948,0.385 0.156,0.198 10 false C 0.792,0.365 0.948,0.563 0.156,0.198 10 false C 0.844,1.302 1,1.5 0.156,0.198 10 false C 0.688,1.792 0.844,1.99 0.156,0.198 10 true C 0.521,2.208 0.677,2.396 0.156,0.188 10 false C 0.677,2.74 0.833,2.927 0.156,0.188 10 false C 1.333,3.083 1.479,3.25 0.146,0.167 10 true C 2.302,2.969 2.448,3.188 0.146,0.219 10 false C 2.448,2.719 2.604,2.906 0.156,0.188 10 false C 1.625,3.26 1.771,3.427 0.146,0.167 10 true C 2.906,0.552 3.063,0.74 0.156,0.188 10 false C 2.969,0.375 3.125,0.563 0.156,0.188 10 false A 2.833,0.729 2.99,0.917 0.156,0.188 10 false B 2.906,0.552 3.063,0.74 0.156,0.188 10 false C 2.667,1.417 2.823,1.604 0.156,0.188 10 false A 2.646,1.031 2.802,1.219 0.156,0.188 10 false B 2.563,1.208 2.719,1.396 0.156,0.188 10 false B 1.719,1.208 1.865,1.375 0.146,0.167 10 true A 1.667,0.677 1.813,0.844 0.146,0.167 10 true B 1.396,1.906 1.5,2.083 0.104,0.177 10 true E 1.583,2.208 1.729,2.375 0.146,0.167 10 true A 1.708,2.51 1.854,2.677 0.146,0.167 10 true A 0.729,0.854 0.885,1.042 0.156,0.188 10 false A 0.906,1.094 1.063,1.281 0.156,0.188 10 false B 0.552,2.021 0.698,2.188 0.146,0.167 10 true D 1.552,1.521 1.74,1.719 0.188,0.198 10 false *1
*1 Seal Washer


Temporarily install the 24 bolts and a new seal washer.

Bolt Length:
Item Length
Bolt A 40 mm (1.575 in.)
Bolt B 50 mm (1.969 in.)
Bolt C, D 25 mm (0.984 in.)
Bolt E 35 mm (1.378 in.)


HINT:
A300629C01
1.667,1.448 1.51,0.813 true 1.323,0.708 1.635,0.865 0.313,0.156 10 false *a
*a Adhesive


1.

Clean and degrease the threads of the bolt (D) and threaded hole of the cylinder block sub-assembly.

2.

Apply adhesive to the bolt (D) more than 7.0 mm (0.276 in.) from the bolt tip.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.





h.
A312261E01
0.948,0.156 1.104,0.333 0.156,0.177 10 true F 3.177,1.198 3.344,1.417 0.167,0.219 10 true F 1.292,1.885 1.458,2.125 0.167,0.24 10 true A

Temporarily install the engine mounting bracket RH to the timing chain cover assembly with the 3 bolts.

Bolt Length:
Item Length
Bolt A 40 mm (1.57 in.)
Bolt F 80 mm (3.15 in.)



i.
A381458E01
0.219,0.375 0.719,0.573 0.5,0.198 10 false 24 (C) 0.26,0.604 0.76,0.802 0.5,0.198 10 false 23 (C) 0.208,0.833 0.708,1.031 0.5,0.198 10 false 7 (F) 0.219,1.219 0.719,1.417 0.5,0.198 10 false 22 (A) 0.469,1.531 0.969,1.729 0.5,0.198 10 false 2 (B) 0.458,1.875 0.958,2.073 0.5,0.198 10 false 6 (A) 0.292,2.125 0.792,2.323 0.5,0.198 10 false 9 (C) 0.104,2.469 0.542,2.635 0.438,0.167 10 true 10 (C) 0,2.708 0.396,2.917 0.396,0.208 10 true 11 (D) 0,2.99 0.396,3.198 0.396,0.208 10 true 12 (C) 0.177,3.667 0.573,3.875 0.396,0.208 10 false 13 (C) 0.74,3.917 1.167,4.083 0.427,0.167 10 true 14 (C) 1.458,0.979 1.865,1.188 0.406,0.208 10 true 4 (B) 1.844,0.708 2.25,0.917 0.406,0.208 10 true 8 (F) 2.927,0.271 3.427,0.469 0.5,0.198 10 false 26 (A) 3.01,0.927 3.427,1.177 0.417,0.25 10 false 25 (C) 2.927,1.188 3.344,1.438 0.417,0.25 10 false 5 (B) 2.698,1.479 3.115,1.729 0.417,0.25 10 false 3 (B) 2.583,1.698 3,1.948 0.417,0.25 10 false 1 (B) 2.719,1.948 3.219,2.198 0.5,0.25 10 false 21 (A) 1.552,1.74 2.052,1.948 0.5,0.208 10 true 20 (A) 1.188,2.677 1.688,2.885 0.5,0.208 10 true 27 (E) 1.354,2.948 1.854,3.156 0.5,0.208 10 true 19 (A) 1.563,3.333 2.063,3.542 0.5,0.208 10 true 18 (A) 2.51,3.604 3.01,3.854 0.5,0.25 10 false 17 (C) 2.281,3.927 2.781,4.177 0.5,0.25 10 false 16 (C) 1.406,4.292 1.906,4.5 0.5,0.208 10 true 15 (C)

Fully tighten the 27 bolts in the sequence shown in the illustration.

Torque:
Bolt A, C and D : 24 N*m (245 kgf*cm, 18 ft.*lbf)
Bolt B : 60.5 N*m (617 kgf*cm, 45 ft.*lbf)
Bolt E : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt F : 71 N*m (724 kgf*cm, 52 ft.*lbf)


j.
A381482

Fully tighten the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16326 32.INSTALL NO. 2 WATER INLET HOUSING GASKET

Hide 16321 33.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 89422 34.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 83530 36.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 11301K 37.INSTALL CRANKSHAFT POSITION SENSOR

Hide 11201 38.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A381480

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

NOTICE:
·

Remove any oil from the contact surfaces.

·

Check that no camshaft bearing cap oil hole gaskets are stuck to the cylinder head cover sub-assembly.




b.
A312291

Install 2 new camshaft bearing cap oil hole gaskets to the camshaft bearing cap.


c.

Remove any old packing material from the contact surface.


d.
A313194C01
0.688,2.75 1,2.906 0.313,0.156 10 false *a 0.667,0.448 0.979,0.604 0.313,0.156 10 false *a
*a Seal Diameter 2.0 mm


Apply seal packing as shown the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

2.0 mm (0.0787 in.)


NOTICE:
·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after the installation.




e.
A381479C04
1,0.656 1.583,0.74 true 1,1.531 1.583,1.448 true 1.656,0.625 1.969,0.781 0.313,0.156 10 true *1 1.656,1.333 1.969,1.49 0.313,0.156 10 true *1 0.438,0.583 0.583,0.75 0.146,0.167 10 true B 0.833,1.073 1,1.229 0.167,0.156 10 true B 0.427,1.469 0.573,1.635 0.146,0.167 10 true B 0.146,0.094 0.292,0.26 0.146,0.167 10 false A 0.938,0.073 1.083,0.24 0.146,0.167 10 false A 1.469,0.042 1.615,0.208 0.146,0.167 10 false A 1.854,0.063 2,0.229 0.146,0.167 10 false A 2.354,0.073 2.5,0.24 0.146,0.167 10 false A 3.198,0.156 3.344,0.323 0.146,0.167 10 false A 3.281,1.198 3.427,1.365 0.146,0.167 10 false A 3.229,1.896 3.375,2.063 0.146,0.167 10 false A 2.625,1.865 2.771,2.031 0.146,0.167 10 false A 2.188,1.865 2.333,2.031 0.146,0.167 10 false A 1.719,1.875 1.865,2.042 0.146,0.167 10 false A 1.125,1.979 1.271,2.146 0.146,0.167 10 false A 0.219,1.938 0.365,2.104 0.146,0.167 10 false A 0.052,1.333 0.198,1.5 0.146,0.167 10 false A
*1 Plate Washer and Seal Washer


Temporarily install the cylinder head cover sub-assembly with the 2 plate washers and 2 new seal washers to the camshaft housing sub-assembly with the 17 bolts.

Bolt Length:
Item Length
Bolt A 23.5 mm (0.925 in.)
Bolt B 35 mm (1.378 in.)



f.
A313291

Apply a light coat of engine oil to the 2 O-rings of the 2 camshaft position sensors.

NOTICE:

If reusing the camshaft position sensor, be sure to inspect the O-ring.



g.
A312286

Temporarily install the 2 camshaft position sensors to the cylinder head cover sub-assembly with the 2 bolts.

NOTICE:
·

If a component has been dropped or subjected to a strong impact, replace the camshaft position sensor.

·

Make sure that the O-ring is not damaged or does not jump out of position during installation.




h.
A381483E02
0.042,1.979 0.354,2.177 0.313,0.198 10 true 15 0.042,1.323 0.354,1.521 0.313,0.198 10 false 17 0.115,0.146 0.427,0.344 0.313,0.198 10 false 12 0.906,0.042 1.219,0.24 0.313,0.198 10 false 6 1.427,0.031 1.74,0.229 0.313,0.198 10 false 10 1.865,0.052 2.177,0.25 0.313,0.198 10 false 4 2.313,0.052 2.625,0.25 0.313,0.198 10 false 8 3.198,0.208 3.427,0.406 0.229,0.198 10 false 14 3.198,1.188 3.427,1.385 0.229,0.198 10 false 16 3.198,1.885 3.427,2.083 0.229,0.198 10 false 13 2.573,1.979 2.802,2.177 0.229,0.198 10 false 11 2.115,1.979 2.344,2.177 0.229,0.198 10 false 7 1.656,1.979 1.885,2.177 0.229,0.198 10 false 5 1.094,1.979 1.323,2.177 0.229,0.198 10 false 9 0.385,1.479 0.615,1.646 0.229,0.167 10 true 19 0.417,0.583 0.646,0.75 0.229,0.167 10 true 18 0.854,1.083 1.021,1.25 0.167,0.167 10 true 1 2.271,0.708 2.438,0.875 0.167,0.167 10 true 2 2.271,1.365 2.438,1.531 0.167,0.167 10 true 3

Fully tighten the 19 bolts in the sequence shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12204A 39.INSTALL VENTILATION SYSTEM GROMMET

a.
A312288

Install the ventilation system grommet to the cylinder head cover sub-assembly.


Hide 12204 40.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 11101J 41.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

a.
A313292

Apply a light coat of engine oil to 2 new O-rings, then install them onto the 2 camshaft timing oil control valve assemblies.

NOTICE:

Do not twist the O-ring.



b.
A312287

Install the 2 camshaft timing oil control valve assemblies to the cylinder head cover sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If a component has been dropped or subjected to a strong impact, replace the camshaft timing oil control valve assembly.

·

Make sure that the O-ring is not damaged or does not jump out of position during installation.




Hide 12108A 43.INSTALL OIL FILLER CAP GASKET

a.
A314370

Install a new oil filler cap gasket to the oil filler cap sub-assembly.


Hide 12108 44.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.
A312285

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.