Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE › from 2017.10
RM30M0E _52 Drivetrain _017093 AXLE AND DIFFERENTIAL _0090088 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502C 1.INSTALL FRONT AXLE HUB SUB-ASSEMBLY

a.

Hold the steering knuckle in a vise between aluminum plates.

NOTICE:

When using a vise, do not overtighten it.



b.

Install the front disc brake dust cover and front axle hub sub-assembly to the steering knuckle with the 3 bolts.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

NOTICE:
·

Do not place the front speed sensor side so that it is facing downward, and do not allow the front speed sensor side to become damaged or contact foreign matter.

·

Do not drop the front axle hub sub-assembly.




Hide 2.INSTALL FRONT AXLE ASSEMBLY

a.
C282325C01
2.771,1.125 3.021,0.802 3.021,0.802 2.906,1.427 true 3,0.646 3.313,0.802 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks on the front drive shaft assembly and front axle hub sub-assembly, and install the front drive shaft assembly to the front axle assembly.

NOTICE:

Be careful not to damage the thread portion of the front drive shaft assembly.



b.

Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.

Torque:
164 N*m (1672 kgf*cm, 121 ft.*lbf)

HINT:

Keep the bolt from rotating while turning the nut.



Hide 48069 3.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.

Install the front lower No. 1 suspension arm sub-assembly to the front axle assembly with the castle nut.


b.

Using a 19 mm ball joint lock nut wrench, fully tighten the castle nut.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:
·

Use the formula to calculate special torque values for situations where a ball joint lock nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the holes for the cotter pin are not aligned, tighten the castle nut by a further turn of up to 60°.

·

Do not allow any oil or grease to contact the threaded or tapered portions.

·

Do not damage the front disc brake dust cover.




c.

Install a new clip.


Hide 45047 4.INSTALL TIE ROD END SUB-ASSEMBLY

a.

Install the tie rod end sub-assembly to the front axle assembly with the castle nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

If the holes for the clip are not aligned, tighten the castle nut by a further turn of up to 60°.

·

Do not damage the front disc brake dust cover.




b.

Install a new cotter pin.


Hide 48819A 5.INSTALL FRONT STABILIZER BOLT (w/o Side Rail Reinforcement)

Hide 48810 6.INSTALL FRONT STABILIZER LINK ASSEMBLY (w/ Side Rail Reinforcement)

Hide 43512 7.INSTALL FRONT DISC

Hide 8.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43502H 9.TEMPORARILY INSTALL FRONT AXLE SHAFT NUT

Hide 10.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 11.REMOVE FRONT DISC

Hide 12.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 43512 14.INSTALL FRONT DISC

Hide 15.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43502H 16.INSTALL FRONT AXLE SHAFT NUT

Hide 17.INSTALL FRONT SPEED SENSOR WIRE

Hide 53876A 18.INSTALL FRONT FENDER LINER

Hide 19.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 20.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT