Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › from 2018.01
RM30M0E _52 Drivetrain _052750 K411 CVT _0259915 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 35150B 1.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

HINT:

After replacing the continuously variable transaxle assembly, perform the following procedure.


a.
C288095

Apply a light coat of Toyota Genuine CVT fluid FE to the 2 O-rings of 2 new transmission case plug assemblies.


b.

Install the 2 transmission case plug assemblies to the continuously variable transaxle assembly.

NOTICE:

Make sure that the O-rings are not damaged or do not jump out of position during installation.



Hide 35141D 2.INSTALL BREATHER PLUG HOSE

HINT:

Perform this procedure only when replacement of the breather plug hose is necessary.


a.

Install the No. 1 breather plug to the breather plug hose.


b.

Install the breather plug hose with the No. 1 breather plug to the continuously variable transaxle assembly.


c.

Engage the clamp and install the breather hose clamp to the breather plug hose.


Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets to the continuously variable transaxle assembly with the 5 bolts.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


b.

Engage the breather hose clamp and install the breather plug hose to the wire harness clamp bracket.


Hide 33823 4.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 30400E 5.INSTALL CVT OIL PUMP TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands, and then apply MP grease to the entire periphery of the lip of a new CVT oil pump type T oil seal.


b.

Temporarily attach the CVT oil pump type T oil seal by pressing it onto the installation surface of the oil pump housing manually.


c.
C208789C03
1.802,1.802 1.802,2.479 false 1.667,2.5 2.094,2.74 0.427,0.24 10 false SST 0.906,2.448 1.125,2.646 0.219,0.198 10 false *a
*a Drive in Depth


Clean the oil seal contact section of SST and the area around it.


d.

Using SST, drive the CVT oil pump type T oil seal in evenly, until it is even with the side surface of the oil pump housing.

SST
09309-36010  

Standard depth:

-0.2 to 0.2 mm (-0.00787 to 0.00787 in.)


NOTICE:
·

Drive the CVT oil pump type T oil seal in gradually, while visually checking the parallelism.

·

After the installation, confirm that the CVT oil pump type T oil seal has been driven in until it is even with the side surface of the oil pump housing.

·

Wipe any extra grease off with your hand.




Hide 32000A 6.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C235896C03
2.083,1.094 2.5,0.677 false 1.042,1.052 1.25,0.823 true 0.75,1.865 0.958,1.635 true 0.5,1.344 0.698,1.344 true 1.302,1.344 1.5,1.344 true 2.531,0.583 2.844,0.74 0.313,0.156 10 false *a 1.271,0.719 1.5,0.927 0.229,0.208 10 true *b 0.344,1.25 0.5,1.458 0.156,0.208 10 true *c 0.573,1.781 0.74,2.01 0.167,0.229 10 true *b 1.49,1.26 1.646,1.469 0.156,0.208 10 true *c
*a Matchmark
*b Wide Groove
*c Narrow Groove


Turn the front oil pump drive gear so that the groove is at the top and place a matchmark on the housing to indicate the position of the groove.

NOTICE:
·

Place the matchmark on the housing to indicate the position of the wide groove.

·

The matchmark position must be correct to prevent damage.




b.
C289838C01
1.188,0.25 1.646,0.417 false 1.188,1.969 1.688,1.635 true 1.031,0.146 1.344,0.302 0.313,0.156 10 false *a 1.021,1.885 1.333,2.042 0.313,0.156 10 false *b
*a Key
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its key is clearly indicated.


c.
C288540C01
2.104,1.167 2.75,0.781 2.75,0.781 2.115,1.51 true 0.625,0.99 1.25,0.906 1.25,0.906 0.615,1.354 true 1.271,0.802 1.583,0.958 0.313,0.156 10 false *1 2.771,0.677 3.083,0.833 0.313,0.156 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




d.
C288541C01
0.615,0.99 1.25,0.885 1.25,0.885 0.615,1.365 true 2.104,1.177 2.521,0.76 true 2.115,2.542 2.771,3.115 true 1.271,0.781 1.583,0.938 0.313,0.156 10 false *1 2.552,0.656 2.865,0.813 0.313,0.156 10 false *a 2.823,3.042 3.135,3.198 0.313,0.156 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




e.
C288542C01
0.615,0.99 1.198,0.885 1.198,0.885 0.604,1.354 true 2.115,1.177 2.698,0.802 2.698,0.802 2.115,1.51 true 1.229,0.781 1.542,0.938 0.313,0.156 10 false *1 2.74,0.698 3.052,0.854 0.313,0.156 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the key of the torque converter assembly into the groove of the front oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C288096C01
2.542,0.969 2.698,0.729 true 2.688,1.906 2.844,1.667 false 1.26,0.865 0.979,0.625 true 1.313,1.094 1.802,0.615 true 2.469,0.979 2.781,1.135 0.313,0.156 10 false *a 2.635,1.948 2.948,2.104 0.313,0.156 10 false *b 2.385,0.365 2.542,0.563 0.156,0.198 10 false A 0.813,0.521 1.125,0.677 0.313,0.156 10 false *a 1.844,0.521 2.156,0.677 0.313,0.156 10 false *b
*a Engine Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure dimension "A" between the continuously variable transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surfaces of the drive plate*b.


h.
C288097N01
2.438,0.667 2.594,0.865 0.156,0.198 10 false B

Using a vernier caliper and straightedge, measure dimension "B" shown in the illustration and check that dimension "B" is more than dimension "A", which was measured in the previous step.

Standard:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 30400 7.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C288568C01
0.969,0.625 0.51,0.406 false 2.938,0.344 1.635,0.865 true 0.354,0.313 0.667,0.469 0.313,0.156 10 false *1 2.969,0.25 3.281,0.406 0.313,0.156 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C288098C01
0.573,0.375 1.198,0.375 true 2.635,1.021 2.917,1.021 true 0.417,0.292 0.729,0.448 0.313,0.156 10 false *1 2.958,0.927 3.271,1.083 0.313,0.156 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C231548N02
1.396,0.375 1.552,0.573 0.156,0.198 10 false A 2.667,0.531 2.823,0.729 0.156,0.198 10 false A 2.99,1.26 3.146,1.458 0.156,0.198 10 false A 3.052,1.854 3.208,2.052 0.156,0.198 10 true A 2.729,2.427 2.885,2.625 0.156,0.198 10 false B 2.385,2.708 2.542,2.906 0.156,0.198 10 false B 1.75,2.813 1.906,3.01 0.156,0.198 10 false B 1.208,2.677 1.365,2.875 0.156,0.198 10 true B

Install the continuously variable transaxle assembly to the engine assembly with the 8 bolts.

Torque:
Bolt A : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt B : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and continuously variable transaxle assembly are in close contact with one another.



HINT:

Bolt length:

·

Bolt A: 45 mm (1.77 in.)

·

Bolt B: 35 mm (1.38 in.)




d.
A192239C42
1.698,1.5 1.698,1.74 false 1.646,1.75 1.823,1.906 0.177,0.156 10 false *a
*a Adhesive


Clean and degrease the bolts and installation holes in the engine mounting bracket LH.


e.

Apply adhesive to 2 or 3 threads on the ends of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



f.
C231550C01
1.427,0.792 1.583,0.969 0.156,0.177 10 true 2 2.438,1.229 2.563,1.396 0.125,0.167 10 true 3 0.427,0.385 0.542,0.542 0.115,0.156 10 false 4 1.823,0.854 2.375,1.063 0.552,0.208 10 true 1 (*a), 5
*a Temporarily Tighten


Install the engine mounting bracket LH to the continuously variable transaxle assembly with the 4 bolts in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


g.
C288091C01
0.979,0.656 1.542,0.865 0.563,0.208 10 true 1 (*a), 6 2.125,1.958 2.24,2.146 0.115,0.188 10 true 2 1.469,1.542 1.583,1.729 0.115,0.188 10 true 3 2.719,1.198 2.833,1.385 0.115,0.188 10 true 4 1.969,0.198 2.083,0.385 0.115,0.188 10 true 5
*a Temporarily Tighten


Install the engine mounting insulator LH to the body with the 5 bolts in the order shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


h.
C288090

Install the engine mounting bracket LH to the engine mounting insulator LH with the bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)

HINT:

Turn the bolt while holding the nut.



Hide 12364B 8.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C219025N02
1.083,0.49 1.24,0.677 0.156,0.188 10 true A 2.521,1.844 2.677,2.021 0.156,0.177 10 false B 1,1.302 1.146,1.49 0.146,0.188 10 false A

Temporarily install the No. 2 engine moving control rod to the continuously variable transaxle assembly with the 3 bolts.

HINT:

Bolt length:

·

Bolt A: 25 mm (0.984 in.)

·

Bolt B: 33.5 mm (1.32 in.)




b.
C219025C01
0.729,0.479 1.25,0.677 0.521,0.198 10 true 1 (*a), 4 1.031,1.313 1.135,1.469 0.104,0.156 10 false 2 2.51,1.854 2.615,2 0.104,0.146 10 false 3
*a Temporarily Tighten


Tighten the 3 bolts in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 51201 9.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 32101G 10.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
A192239C42
1.698,1.5 1.698,1.74 false 1.646,1.75 1.823,1.906 0.177,0.156 10 false *a
*a Adhesive


Remove any adhesive remaining in the 6 drive plate and torque converter assembly setting bolts.


b.

Apply a few drops of adhesive to 2 or 3 threads at the tips of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.
A305670N01
0.635,1.833 0.958,1.708 false 0.344,1.75 0.802,1.948 0.458,0.198 10 false SST

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:
·

First install the black-colored bolt, and then the remaining 5 silver-colored bolts.

·

Do not start the engine for at least 1 hour after installing the drive plate and torque converter assembly setting bolts.




Hide 82121 11.CONNECT ENGINE WIRE

a.

Install the wire harness clamp bracket to the continuously variable transaxle assembly with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


b.

Install the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


c.

Engage the 8 clamps and install the engine wire to the continuously variable transaxle assembly.


d.

Connect the 6 connectors to the continuously variable transaxle assembly.


Hide 16260 12.CONNECT WATER BY-PASS HOSE ASSEMBLY

a.
C354298C01
1.469,3.052 1.333,2.76 false 1.031,1.698 1.188,1.896 0.156,0.198 10 false A 1.573,1.969 1.729,2.167 0.156,0.198 10 false A 0.542,2.198 0.698,2.396 0.156,0.198 10 false *a 1.5,2.656 1.656,2.854 0.156,0.198 10 false *c 1,3.177 1.156,3.375 0.156,0.198 10 false *b 1.427,3.073 1.583,3.271 0.156,0.198 10 false *d
*a View A
*b Front of Vehicle
*c Left of Vehicle
*d Blue Mark


Engage the 2 clamps to install the water by-pass hose assembly to the continuously variable transaxle assembly.


b.

Connect the 2 water by-pass hoses to the transmission oil cooler and slide the 2 hose clips to secure them as shown in the illustration.

NOTICE:
·

Fully insert the 2 water by-pass hoses until the 2nd rib on each transmission oil cooler pipe.

·

Perform the installation with the hose clips at the correct directions.




Hide 35141F 13.INSTALL NO. 1 BREATHER PLUG

a.

Engage the clamp and install the No. 1 breather plug to the hose clamp.


Hide 11363A 14.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 28100 15.INSTALL STARTER ASSEMBLY

Hide 43498A 17.INSTALL NO. 1 DRIVE SHAFT HEAT INSULATOR

Hide 17410 18.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 19.INSTALL FRONT FLOOR CENTER BRACE

Hide 45025D 20.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 21.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45209 22.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 23.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 33820B 24.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 58810J 25.INSTALL CONSOLE BOX ASSEMBLY

Hide 58839A 26.INSTALL CONSOLE BOX HOLE COVER

Hide 58912C 28.INSTALL NO. 2 BOX SIDE PANEL

Hide 58911A 29.INSTALL NO. 1 BOX SIDE PANEL

Hide 58817A 30.INSTALL NO. 2 FRONT CONSOLE BOX INSERT

Hide 58910C 32.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 17701 36.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 37.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17880 39.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 40.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 43.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 45.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK

Hide 46.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


Hide 47.INSPECT SHIFT LEVER POSITION

Hide 48.ADJUST SHIFT LEVER POSITION

Hide 51441C 49.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51442C 50.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51405A 51.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 52.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 53.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT