[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
54 -CHASSIS ELECTRICAL > 54A-CHASSIS ELECTRICAL > ETACS > DIAGNOSIS CODE CHART
DIAGNOSIS CODE CHART
Diagnosis code No.Diagnostic itemReference page
B1034Ambient temperature sensor lowRefer to GROUP 55 - Diagnosis code chart .
B1035Ambient temperature sensor high
B16A2Turn signal lampTurn signal(LH) bulb outageRefer to diagnosis code chart
B16A3Turn signal(LH) circuit short
B16A4Turn signal(RH) bulb outage
B16A5Turn signal(RH) circuit short
B16A6Turn signal fuse blown
B16A9Turn lamp(LH) deactivated
B16AATurn lamp(RH) deactivated
B16A7Rear combination lampTail lamp(RH) circuit short <Short circuit in the position lamp (RH) circuit or the tail lamp (RH) circuit>Refer to diagnosis code chart
B16A8Tail lamp(LH) circuit short <Short circuit in the position lamp (LH) circuit, tail lamp (LH) circuit or the licence plate lamp circuit>
B1E17Tail lamp(RH) deactivated (FET failure)
B1E18Tail lamp(LH) deactivated (FET failure)
B1E1CStoplamp Overload or Short Circuit
B1761*1Chassis No. not programmed
B1762*2IOD fuse not seated fully
B1731Immobilizer systemENG ECU authentication timeoutRefer to diagnosis code chart
B1A24Transponder ID not registered
B1A25Transponder ID unmatched
B1A28ENG ECU authentication error
B1A35Transponder read error
B2352Antenna fail
B1E11HeadlampLow Beam Lamp(RH) Open Load or Blown ErrorRefer to diagnosis code chart
B1E12Low Beam Lamp(LH) Open Load or Blown Error
B1E13Low Beam Lamp(RH) Overload or Short Circuit
B1E14Low Beam Lamp(LH) Overload or Short Circuit
B1E15Low Beam Lamp(RH) deactivated (FET failure)
B1E16Low Beam Lamp(LH) deactivated (FET failure)
B1E2AMultichannel Driver CH6 Defective (Open/Short)
B1E19Fog lampRear Fog Lamp(LH/RH) Open Load or Blown ErrorRefer to diagnosis code chart
B1E1ARear Fog Lamp(LH/RH) Overload or Short Circuit
B1E1BRear Fog Lamp(LH/RH) deactivated (FET failure)
B1E2CMultichannel Driver CH8 Defective (Open/Short)
B1E1DInterior lamp+Battery Roomlamp Overload or Short CircuitRefer to diagnosis code chart
B1E1ERoomlamp Control Overload or Short Circuit
B1E20+Battery Roomlamp deactivated (FET failure)
B1E21Roomlamp deactivated (FET failure)
B1E27Daytime running lampMultichannel Driver CH3 Defective (Open/Short)Refer to diagnosis code chart
B1E2DFront wiper auto stop switchRefer to GROUP 51 - Diagnosis code chart .
B210A+B power supply (low)
B210B+B power supply (high)
B2206*1Chassis No. mismatch
B2215*1ECU internal error (EEPROM)
B222C*1Coding not completed
B2350Column switchLighting switchRefer to diagnosis code chart
B2351Wiper switch
B2353Ignition power supply (low)
B2354Ignition power supply (high)
B2510Headlamp automatic levelling systemHeight Sensor Not InitialisedRefer to diagnosis code chart
B2513Levelling actuator output voltage
B2514Height sensor supply voltage
B2515Front height sensor signal
B2516Rear height sensor signal
U0100CAN communicationEngine CAN timeout
U0101T/M CAN timeout
U01144WD CAN timeout
U0121ABS/ASC CAN timeout
U0131EPS CAN timeout
U0146GATEWAY CAN timeout
U0151SRS-ABG CAN timeout
U0155Meter CAN timeout
U0159CAMERA CAN timeout
U0164A/C CAN timeout
U0168KOS/WCM CAN timeout
U0184Audio CAN timeout
U0245AND CAN timeout
U1000OSS CAN timeout
U1005Corner/Back SNS.ECU CAN timeout
U1018BSW CAN timeout
U15A0ACC/FCM ECU CAN timeout
U15A5FCM/LDW/AHB CAN timeout
U0331ECU internal error (ROM)
U1073Bus off (CAN-C-Mid)
U0169LIN communicationSunroof LIN timeout <Vehicles with sunroof>Refer to GROUP 54B - Diagnosis Code Chart .
U0231RLS LIN timeout
U1006Security alarm siren LIN timeout <Vehicles with security alarm sensor>
U1007Security alarm sensor LIN timeout <Vehicles with security alarm sensor>
U150BColumn SW LIN checksum error
U1511Sunroof ECU LIN checksum error <Vehicles with sunroof>
U1512RLS LIN checksum error
U1514LIN transmission bit error
U1515No bus activity error for LIN
U1539Security alarm siren LIN checksum <Vehicles with security alarm sensor>
U1540Security alarm SNSR.LIN checksum <Vehicles with security alarm sensor>
note
  • *1: If diagnosis codes No. B1761, B2206, B2215, B222C is set, there may be an error with the coding data set in the ETACS-ECU.
  • *2: Does not detect historic trouble.