DTC C1237 Speed Sensor Rotor Faulty |
DTC C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1237 | Any of the following is detected:
|
|
| C1275 C1276 | Detected only during Test Mode. | Front speed sensor rotor RH/LH (Front axle hub sub-assembly RH/LH) |
| C1277 C1278 | Detected only during Test Mode. | Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) |
| 1.CHECK TIRES |
Check the size and condition of all four wheels (Click here).
|
| ||||
| OK | |
| 2.READ VALUE USING GTS (SPEED SENSOR) |
Connect the GTS to the DLC3.
Start the engine.
Select the Data List using the GTS (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Check the speed value output from the speed sensor displayed on the GTS.
| Result | Proceed to |
| OK | A |
| NG (for front) | B |
| NG (for rear) | C |
|
| ||||
|
| ||||
| A | |
| 3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check using the Test Mode procedure (Click here).
| Result | Proceed to |
| OK | A |
| NG (for front) | B |
| NG (for rear) | C |
|
| ||||
|
| ||||
| A | |
| 4.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is not output. | A |
| DTC C1237 is output (for front). | B |
| DTC C1237 is output (for rear). | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK FRONT SPEED SENSOR INSTALLATION |
![]() |
Turn the ignition switch off.
Check the speed sensor installation.
|
| ||||
| OK | |
| 6.CHECK FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR) |
Install the front speed sensor (Click here).
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A5-16 (FR+) - A42-2 (FR+) | Always | Below 1 Ω |
| A5-16 (FR+) - Body ground | Always | 10 kΩ or higher |
| A5-4 (FR-) - A42-1 (FR-) | Always | Below 1 Ω |
| A5-4 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A5-19 (FL+) - A12-2 (FL+) | Always | Below 1 Ω |
| A5-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A5-32 (FL-) - A12-1 (FL-) | Always | Below 1 Ω |
| A5-32 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.RECONFIRM DTC |
Reconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | |
| 9.REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
| NEXT | |
| 10.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | |
| 11.REPLACE FRONT SPEED SENSOR ROTOR |
Turn the ignition switch off.
Replace the front speed sensor rotor (Click here).
| NEXT | |
| 12.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | ||
| ||
| 13.CHECK REAR SPEED SENSOR INSTALLATION |
![]() |
Turn the ignition switch off.
Check the speed sensor installation.
|
| ||||
| OK | |
| 14.CHECK REAR SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the speed sensor tip.
|
| ||||
| OK | |
| 15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR) |
Install the rear speed sensor (Click here).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake actuator assembly) connector and the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A5-17 (RR+) - G9-2 (RR+) | Always | Below 1 Ω |
| A5-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A5-29 (RR-) - G9-1 (RR-) | Always | Below 1 Ω |
| A5-29 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A5-31 (RL+) - H12-2 (RL+) | Always | Below 1 Ω |
| A5-31 (RL+) - Body ground | Always | 10 kΩ or higher |
| A5-18 (RL-) - H12-1 (RL-) | Always | Below 1 Ω |
| A5-18 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 16.RECONFIRM DTC |
Reconnect the skid control ECU (brake actuator assembly) connector and the rear speed sensor connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | |
| 17.REPLACE REAR SPEED SENSOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
| NEXT | |
| 18.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | |
| 19.REPLACE REAR SPEED SENSOR ROTOR |
Turn the ignition switch off.
Replace the rear speed sensor rotor (Click here).
| NEXT | |
| 20.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | ||
| ||