Home › Engine / Hybrid System › M20A-FXS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _083976 M20A-FXS ENGINE MECHANICAL _0404774 CYLINDER HEAD GASKET A

M20A-FXS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: If the vehicle height has changed due to suspension or tire replacement

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Clear zero point calibration data

2.

Perform yaw rate and acceleration sensor zero point calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.*2
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 16261Z 5.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
A426129

Slide the clip and disconnect the No. 1 water by-pass hose from the cylinder block sub-assembly.


Hide 16264 6.DISCONNECT NO. 2 WATER BY-PASS HOSE

a.
A426130

Slide the clip and disconnect the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.


Hide 16268 7.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 17167 8.SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 22030 11.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 12.REMOVE THROTTLE BODY GASKET

Hide 25680 13.REMOVE EGR COOLER ASSEMBLY

Hide 25601 14.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25620 15.REMOVE EGR VALVE ASSEMBLY

Hide 16279 16.REMOVE NO. 3 WATER BY-PASS PIPE

Hide 17138B 17.REMOVE INTAKE MANIFOLD STAY

Hide 17177 19.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23910A 20.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 21.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 22.REMOVE FUEL PUMP ASSEMBLY (for High Pressure)

Hide 16260 23.REMOVE WATER BY-PASS HOSE ASSEMBLY

Hide 23807 24.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23291 26.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 28.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 30.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452D 33.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15250 34.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 35.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 36.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 37.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 38.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 13090E 39.REMOVE CAM TIMING CONTROL MOTOR O-RING

Hide 13470 40.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 16304 41.REMOVE WATER OUTLET SUB-ASSEMBLY

Hide 16351 42.REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY

Hide 11201 43.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 44.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 45.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320B 46.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 47.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 48.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13507A 49.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

Hide 13050 50.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 52.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 53.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 54.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 55.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 56.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 23477 57.REMOVE FUEL PUMP LIFTER GUIDE

Hide 11103 58.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 60.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

Hide 61.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

Hide 13801 62.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 63.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 64.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 65.REMOVE CYLINDER HEAD GASKET

A426101

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 66.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 67.INSPECT CYLINDER HEAD SUB-ASSEMBLY