After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 CAN JUNCTION CONNECTOR (for TMMT Made without Blind Spot Monitor System)
Check the No. 1 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to Central Gateway ECU (Network Gateway ECU) | - | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F112-1 (CANH) | SB | Clearance warning ECU assembly*1
(for Bus 1) |
| F112-12 (CANL) | GR | |
| F112-2 (CANH) | R | Forward recognition camera*2
(for Bus 1) |
| F112-13 (CANL) | GR | |
| F112-3 (CANH) | G | Millimeter wave radar sensor assembly*2
(for Bus 1) |
| F112-14 (CANL) | GR | |
| F112-4 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F112-15 (CANL) | GR | |
| F112-5 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F112-16 (CANL) | GR |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
NO. 1 CAN JUNCTION CONNECTOR (for TMMT Made with Blind Spot Monitor System)
Check the No. 1 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to No. 6 CAN Junction Connector | *f | to Central Gateway ECU (Network Gateway ECU) |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F112-1 (CANH) | SB | Clearance warning ECU assembly*1
(for Bus 1) |
| F112-12 (CANL) | GR | |
| F112-2 (CANH) | R | Forward recognition camera*2
(for Bus 1) |
| F112-13 (CANL) | GR | |
| F112-3 (CANH) | G | Millimeter wave radar sensor assembly*2
(for Bus 1) |
| F112-14 (CANL) | GR | |
| F112-4 (CANH) | B | No. 6 CAN junction connector
(for Bus 1) |
| F112-15 (CANL) | GR | |
| F112-5 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F112-16 (CANL) | GR |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
NO. 1 CAN JUNCTION CONNECTOR (for TMC Made)
Check the No. 1 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to No. 6 CAN Junction Connector | *f | to Central Gateway ECU (Network Gateway ECU) |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F164-1 (CANH) | SB | Clearance warning ECU assembly*1
(for Bus 1) |
| F164-7 (CANL) | GR | |
| F164-2 (CANH) | R | Forward recognition camera*2
(for Bus 1) |
| F164-8 (CANL) | GR | |
| F164-3 (CANH) | G | Millimeter wave radar sensor assembly*2
(for Bus 1) |
| F164-9 (CANL) | GR | |
| F164-5 (CANH) | B | No. 6 CAN junction connector
(for Bus 1) |
| F164-11 (CANL) | GR | |
| F164-6 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F164-12 (CANL) | GR |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
NO. 3 CAN JUNCTION CONNECTOR
Check the No. 3 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to Combination Meter Assembly |
| *c | to Main Body ECU (Multiplex Network Body ECU) | *d | to Headlight ECU Sub-assembly LH
(for LED Headlight) |
| *e | to Air Conditioning Amplifier Assembly | *f | to Certification ECU (Smart Key ECU Assembly)
(w/ Entry and Start System) |
| *g | to Central Gateway ECU (Network Gateway ECU) | *h | to Telematics Transceiver
(w/ Manual (SOS) Switch) |
| *i | to Radio and Display Receiver Assembly
(for Radio and Display Type) |
- | - |
Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F114-1 (CANH) | V | Combination meter assembly
(for Bus 5) |
| F114-12 (CANL) | SB | |
| F114-2 (CANH) | G | Main body ECU (multiplex network body ECU)
(for Bus 5) |
| F114-13 (CANL) | SB | |
| F114-3 (CANH) | L | Headlight ECU sub-assembly LH*1
(for Bus 5) |
| F114-14 (CANL) | SB | |
| F114-4 (CANH) | P | Air conditioning amplifier assembly
(for Bus 5) |
| F114-15 (CANL) | SB | |
| F114-5 (CANH) | R | Certification ECU (smart key ECU assembly)*2
(for Bus 5) |
| F114-16 (CANL) | SB | |
| F114-6 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 5) |
| F114-17 (CANL) | SB | |
| F114-8 (CANH) | GR | Telematics transceiver*3
(for Bus 3) |
| F114-19 (CANL) | LG | |
| F114-9 (CANH) | B | Radio and display receiver assembly*4
(for Bus 3) |
| F114-20 (CANL) | LG | |
| F114-10 (CANH) | G | Central gateway ECU (network gateway ECU)
(for Bus 3) |
| F114-21 (CANL) | LG | |
| F114-11 (CANH) | V | Central gateway ECU (network gateway ECU)
(for Bus 3) |
| F114-22 (CANL) | LG |
*1: w/ Headlight ECU
*2: w/ Entry and Start System
*3: w/ Manual (SOS) Switch
*4: for Radio and Display Type
NO. 4 CAN JUNCTION CONNECTOR (for RHD)
Check the No. 4 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Airbag Sensor Assembly |
| *c | to Power Steering ECU Assembly | *d | to 4WD ECU Assembly
(for AWD) |
| *e | to Steering Sensor | *f | to No. 5 CAN Junction Connector |
Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F115-1 (CANH) | B | Airbag sensor assembly
(for Bus 4) |
| F115-12 (CANL) | W | |
| F115-3 (CANH) | P | Power steering ECU assembly
(for Bus 4) |
| F115-14 (CANL) | W | |
| F115-4 (CANH) | L | 4WD ECU assembly*1
(for Bus 4) |
| F115-15 (CANL) | W | |
| F115-5 (CANH) | BE | Steering sensor
(for Bus 4) |
| F115-16 (CANL) | W | |
| F115-6 (CANH) | GR | No. 5 CAN junction connector
(for Bus 4) |
| F115-17 (CANL) | W |
*1: for AWD
NO. 5 CAN JUNCTION CONNECTOR (for RHD)
Check the No. 5 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Brake Actuator Assembly |
Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F117-1 (CANH) | GR | No. 4 CAN junction connector
(for Bus 4) |
| F117-12 (CANL) | W | |
| F117-2 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 4) |
| F117-13 (CANL) | W | |
| F117-7 (CANH) | LG | Brake actuator assembly
(for Bus 4) |
| F117-18 (CANL) | W |
NO. 4 CAN JUNCTION CONNECTOR (for LHD)
Check the No. 4 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Airbag Sensor Assembly |
| *c | to Steering Sensor | *d | to Power Steering ECU Assembly |
| *e | to No. 5 CAN Junction Connector | - | - |
Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F123-1 (CANH) | B | Airbag sensor assembly
(for Bus 4) |
| F123-12 (CANL) | W | |
| F123-5 (CANH) | BE | Steering sensor
(for Bus 4) |
| F123-16 (CANL) | W | |
| F123-6 (CANH) | P | Power steering ECU assembly
(for Bus 4) |
| F123-17 (CANL) | W | |
| F123-7 (CANH) | GR | No. 5 CAN junction connector
(for Bus 4) |
| F123-18 (CANL) | W |
NO. 5 CAN JUNCTION CONNECTOR (for LHD)
Check the No. 5 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Brake Actuator Assembly |
| *e | to 4WD ECU Assembly
(for AWD) |
- | - |
Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F124-1 (CANH) | GR | No. 4 CAN junction connector
(for Bus 4) |
| F124-12 (CANL) | W | |
| F124-2 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 4) |
| F124-13 (CANL) | W | |
| F124-5 (CANH) | LG | Brake actuator assembly
(for Bus 4) |
| F124-16 (CANL) | W | |
| F124-6 (CANH) | L | 4WD ECU assembly*1
(for Bus 4) |
| F124-17 (CANL) | W |
*1: for AWD
NO. 6 CAN JUNCTION CONNECTOR (w/ Blind Spot Monitor System)
Check the No. 6 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) (for TMC Made) |
| *c | to Blind Spot Monitor Sensor LH | *d | to Central Gateway ECU (Network Gateway ECU) (for TMMT Made) |
| *e | to No. 1 CAN Junction Connector | - | - |
Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M104-8 (CANH) | R | Central gateway ECU (network gateway ECU)*1
(for Bus 1) |
| M104-19 (CANL) | GR | |
| M104-9 (CANH) | G | Blind spot monitor sensor LH
(for Bus 1) |
| M104-20 (CANL) | GR | |
| M104-10 (CANH) | R | Central gateway ECU (network gateway ECU)*2
(for Bus 1) |
| M104-21 (CANH) | GR | |
| M104-11 (CANH) | B | No. 1 CAN junction connector
(for Bus 1) |
| M104-22 (CANL) | GR |
*1: for TMC Made
*1: for TMMT Made
DLC3
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F144-6 (CANH) - F144-14 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F144-6 (CANH) - F144-4 (CG) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F144-14 (CANL) - F144-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F144-6 (CANH) - F144-16 (BAT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F144-14 (CANL) - F144-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
| *a | Component without harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-14 (CA6H) - F74-5 (CA6L) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| F74-14 (CA6H) - F74-10 (GND) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-5 (CA6L) - F74-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-14 (CA6H) - F74-1 (BATT) | R - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F74-5 (CA6L) - F74-1 (BATT) | W - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-23 (CA1H) - F74-9 (CAXH) | R - P | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| F74-8 (CA1L) - F74-24 (CAXL) | GR - GR | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| F74-23 (CA1H) - F74-10 (GND) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-8 (CA1L) - F74-10 (GND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-23 (CA1H) - F74-1 (BATT) | R - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F74-8 (CA1L) - F74-1 (BATT) | GR - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-18 (CA4H) - F74-17 (CA4L) | R - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F74-18 (CA4H) - F74-10 (GND) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-17 (CA4L) - F74-10 (GND) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-18 (CA4H) - F74-1 (BATT) | R - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F74-17 (CA4L) - F74-1 (BATT) | P - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-6 (CA3H) - F74-19 (CAYH) | G - V | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| F74-21 (CA3L) - F74-20 (CAYL) | LG - LG | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| F74-6 (CA3H) - F74-10 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-21 (CA3L) - F74-10 (GND) | LG - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-6 (CA3H) - F74-1 (BATT) | G - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F74-21 (CA3L) - F74-1 (BATT) | LG - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-22 (CA2H) - F74-7 (CA2L) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F74-22 (CA2H) - F74-10 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-7 (CA2L) - F74-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-22 (CA2H) - F74-1 (BATT) | B - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F74-7 (CA2L) - F74-1 (BATT) | W - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-15 (CA5H) - F74-16 (CA5L) | B - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F74-15 (CA5H) - F74-10 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-16 (CA5L) - F74-10 (GND) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F74-15 (CA5H) - F74-1 (BATT) | B - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F74-16 (CA5L) - F74-1 (BATT) | SB - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STEERING SENSOR
| *a | Component without harness connected
(Steering Sensor) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F69 steering sensor connector.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F69-3 (CANH) - F69-2 (CANL) | BE - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F69-3 (CANH) - F69-1 (ESS) | BE - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F69-2 (CANL) - F69-1 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F69-3 (CANH) - F69-5 (BAT) | BE - P | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F69-2 (CANL) - F69-5 (BAT) | W - P | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM (for 8NR-FTS)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
for TMMT Made:
Disconnect the cable from the negative (-) battery terminal.
Disconnect the A38 and C62 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A38-13 (CANH) - A38-26 (CANL) | GR - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A38-13 (CANH) - C62-53 (E1) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-26 (CANL) - C62-53 (E1) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-13 (CANH) - A38-1 (BATT) | GR - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A38-26 (CANL) - A38-1 (BATT) | P - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
for TMC Made:
Disconnect the cable from the negative (-) battery terminal.
Disconnect the A38 and C74 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A38-13 (CANH) - A38-26 (CANL) | R - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A38-13 (CANH) - C74-53 (E1) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-26 (CANL) - C74-53 (E1) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-13 (CANH) - A38-1 (BATT) | R - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A38-26 (CANL) - A38-1 (BATT) | P - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM (for 3ZR-FAE)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) battery terminal.
Disconnect the A38 and C63 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A38-13 (CANH) - A38-26 (CANL) | R - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A38-13 (CANH) - C63-59 (E1) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-26 (CANL) - C63-59 (E1) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-13 (CANH) - A38-1 (BATT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A38-26 (CANL) - A38-1 (BATT) | P - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F4 combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F4-32 (CANH) - F4-31 (CANL) | V - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F4-32 (CANH) - F4-21 (ET) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F4-31 (CANL) - F4-21 (ET) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F4-32 (CANH) - F4-40 (B) | V - SB | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F4-31 (CANL) - F4-40 (B) | SB - SB | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY
Refer to Terminals of ECU.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the A42 brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A42-5 (CANH) - A42-19 (CANL) | LG - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A42-5 (CANH) - A42-46 (GND1) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A42-19 (CANL) - A42-46 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A42-5 (CANH) - A42-30 (+BS) | LG - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A42-19 (CANL) - A42-30 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F15 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F15-14 (CANH) - F15-13 (CANL) | G - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F15-14 (CANH) - F144-4 (CG) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F15-13 (CANL) - F144-4 (CG) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F15-14 (CANH) - F144-16 (BAT) | G - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F15-13 (CANL) - F144-16 (BAT) | SB - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F1-1 (CANH) - F1-2 (CANL) | R - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F1-1 (CANH) - F1-18 (E) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F1-2 (CANL) - F1-18 (E) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F1-1 (CANH) - F1-4 (+B) | R - L | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F1-2 (CANL) - F1-4 (+B) | SB - L | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POWER STEERING ECU ASSEMBLY
Refer to Terminals of ECU.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F23 and F68 power steering ECU assembly connectors.
| *a | Front view of wire harness connector
(to Power Steering ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F23-7 (CANH) - F23-8 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F23-7 (CANH) - F68-2 (PGND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F23-8 (CANL) - F68-2 (PGND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F23-7 (CANH) - F68-1 (PIG) | P - B-W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F23-8 (CANL) - F68-1 (PIG) | W - B-W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F142 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F142-17 (R1) - F142-18 (R2) | SB - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F142-17 (R1) - F142-28 (E) | SB - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F142-18 (R2) - F142-28 (E) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F142-17 (R1) - F144-16 (BAT) | SB - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F142-18 (R2) - F144-16 (BAT) | GR - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F150 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F150-26 (CANH) - F150-27 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F150-26 (CANH) - F150-33 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F150-27 (CANL) - F150-33 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F150-26 (CANH) - F144-16 (BAT) | B - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F150-27 (CANL) - F144-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Top-mounted Air Conditioner Pressure Sensor)
Refer to Terminals of ECU.
for Automatic Air Conditioning System: Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System with Top-mounted Air Conditioner Pressure Sensor)>TERMINALS OF ECU
for Manual Air Conditioning System: Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F72 air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F72-9 (CANH) - F72-10 (CANL) | P - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F72-9 (CANH) - F72-29 (GND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F72-10 (CANL) - F72-29 (GND) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F72-9 (CANH) - F72-1 (B) | P - V | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F72-10 (CANL) - F72-1 (B) | SB - V | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Side-mounted Air Conditioner Pressure Sensor)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F73 air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F73-11 (CANH) - F73-12 (CANL) | P - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F73-11 (CANH) - F73-4 (GND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F73-12 (CANL) - F73-4 (GND) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F73-11 (CANH) - F73-1 (B) | P - V | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F73-12 (CANL) - F73-1 (B) | SB - V | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F129 and F131 radio and display receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F131-13 (CANH) - F131-14 (CANL) | B - LG | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F131-13 (CANH) - F129-1 (GND1) | B - LA | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F131-14 (CANL) -F129-1 (GND1) | LG - LA | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F131-13 (CANH) - F129-4 (+B1) | B - LA-SB | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F131-14 (CANL) - F129-4 (+B1) | LG - LA-SB | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY LH (w/ Headlight ECU)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the A16*1 or A95*2 headlight ECU sub-assembly LH connector.
*1: for TMC Made
*1: for TMMT Made
Measure the resistance according to the value(s) in the table below.
| *A | for TMC Made | *B | for TMMT Made |
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Headlight ECU Sub-assembly LH) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A16-24 (CANH) - A16-23 (CANL) | Y - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A16-24 (CANH) - A16-12 (GND) | Y - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A16-23 (CANL) - A16-12 (GND) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A16-24 (CANH) - F144-16 (BAT) | Y - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A16-23 (CANL) - F144-16 (BAT) | SB- R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A95-24 (CANH) - A95-23 (CANL) | L - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A95-24 (CANH) - A95-12 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A95-23 (CANL) - A95-12 (GND) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A95-24 (CANH) - F144-16 (BAT) | L - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A95-23 (CANL) - F144-16 (BAT) | SB- R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the M62 blind spot monitor sensor LH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| M62-2 (CA1P) - M62-7 (CA1N) | G - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| M62-2 (CA1P) - M62-10 (BLGD) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M62-7 (CA1N) - M62-10 (BLGD) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M62-2 (CA1P) - F144-16 (BAT) | G - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M62-7 (CA1N) - F144-16 (BAT) | GR - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the R5 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R5-5 (CA1P) - R5-11 (CA1N) | R - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| R5-5 (CA1P) - R5-10 (GND) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R5-11 (CA1N) - R5-10 (GND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R5-5 (CA1P) - F144-16 (BAT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| R5-11 (CA1N) - F144-16 (BAT) | GR - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the A2 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A2-3 (CA2H) - A2-2 (CA2L) | G - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A2-3 (CA2H) - A2-1 (SGND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A2-2 (CA2L) - A2-1 (SGND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A2-3 (CA2H) - F144-16 (BAT) | G - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A2-2 (CA2L) - F144-16 (BAT) | GR - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TELEMATICS TRANSCEIVER (w/ Manual (SOS) Switch)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Telematics Transceiver) |
Disconnect the F51 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F51-15 (CANP) - F51-16 (CANN) | GR - LG | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F51-15 (CANP) - F51-4 (E) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F51-16 (CANN) - F51-4 (E) | LG - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F51-15 (CANP) - F51-1 (+B) | GR - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F51-16 (CANN) - F51-1 (+B) | LG - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
4WD ECU ASSEMBLY (for AWD)
Refer to Terminals of ECU.
Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the M77 4WD ECU assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to 4WD ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| M77-6 (CANH) - M77-5 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| M77-6 (CANH) - M77-4 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M77-5 (CANL) - M77-4 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M77-6 (CANH) - F144-16 (BAT) | L - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M77-5 (CANL) - F144-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
PARKING ASSIST ECU (w/ Panoramic View Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the M116 parking assist ECU connector.
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| M116-40 (CANH) - M116-18 (CANL) | L - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| M116-40 (CANH) - M116-2 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M116-18 (CANL) - M116-2 (GND1) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M116-40 (CANH) - M116-1 (+B) | L - L | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M116-18 (CANL) - M116-1 (+B) | GR - L | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |