Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2021.02
RM33A0E _51 Engine / Hybrid System _098627 M20A-FKS ENGINE MECHANICAL _0463502 ENGINE UNIT A

M20A-FKS ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
·

Perform reset memory

·

Perform road test to allow TCM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless Door Lock Control System

·

Engine start


See Service Bulletin for the registration method
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of front bumper assembly Front television camera view adjustment Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Replacement of front bumper assembly
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 43457 1.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A443855

Remove the 3 bolts and drive shaft bearing bracket.


Hide 16361A 2.REMOVE V-RIBBED BELT

Hide 88310 4.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

Hide 16620D 5.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

NOTICE:
A409240

·

Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.

·

Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.



a.
A443856

Remove the 2 bolts and V-ribbed belt tensioner assembly from the No. 2 timing chain cover assembly.


Hide 16207 6.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A465547

Slide the clip and disconnect the No. 2 water by-pass pipe sub-assembly from the water by-pass outlet sub-assembly.


b.

Remove the bolt and No. 2 water by-pass pipe sub-assembly from the water hose clamp bracket.


Hide 16260 7.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A465548

Remove the bolt and the flow shutting valve (water by-pass hose assembly) from the water hose clamp bracket.


Hide 16575B 8.REMOVE WATER HOSE CLAMP BRACKET

a.
A433287

Remove the 2 bolts and water hose clamp bracket from the camshaft housing sub-assembly.


Hide 17167 9.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17141 11.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 22030 12.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 13.REMOVE THROTTLE BODY GASKET

Hide 25680 14.REMOVE EGR COOLER ASSEMBLY

Hide 25601 15.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25620 16.REMOVE EGR VALVE ASSEMBLY

Hide 16279 17.REMOVE NO. 3 WATER BY-PASS PIPE

a.
A444185

Using an 8 mm socket wrench, remove the bolt and disconnect No. 3 water by-pass pipe from the intake manifold.


b.

Slide the clip and remove the No. 3 water by-pass pipe from the water outlet.


Hide 17138B 18.REMOVE INTAKE MANIFOLD STAY

Hide 17177 20.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23910A 21.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A445467

Disconnect the fuel tube sub-assembly from the fuel pump assembly (for high pressure).

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


b.
A445468

Remove the fuel pipe clamp from the fuel tube connector.


c.
A445469

Remove the fuel tube sub-assembly from the fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23801P 22.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A425015

Remove the bolt.


b.

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


Hide 23100X 23.REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 24.REMOVE NO. 1 WATER BY-PASS HOSE ASSEMBLY

a.
A425017

Remove the bolt.


b.

Slide the 2 clips and remove the No. 1 water by-pass hose assembly from the water inlet with thermostat sub-assembly and cylinder head sub-assembly.


Hide 82219A 25.REMOVE SENSOR WIRE

a.
A425179

Disconnect the 4 connectors.


b.

Disengage the 3 clamps.


c.

Remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.


Hide 82126A 26.REMOVE NO. 6 ENGINE WIRE

a.
A425181

Disconnect the 4 connectors.


b.

Disengage the 2 clamps.


c.

Remove the 2 nuts and No. 6 engine wire from the wire harness clamp bracket.


Hide 23807 27.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23291 29.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 31.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 33.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452D 36.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A425020

Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the cylinder head sub-assembly.


c.
A425021

Remove the O-ring from the engine oil level dipstick guide.


Hide 16031 37.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 16032 38.REMOVE ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

a.
A400319

Remove the 4 bolts, engine water pump assembly (water inlet housing) and gasket from the cylinder block sub-assembly.


Hide 17169A 39.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.
A443858

Remove the 2 bolts and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.


Hide 25759A 41.REMOVE VACUUM SURGE TANK BRACKET

a.
A444187

Using an 8 mm socket wrench, remove the 2 bolts and vacuum surge tank bracket from the camshaft housing sub-assembly.


Hide 12262 42.REMOVE NO. 2 VENTILATION HOSE

a.
A444188

Slide the clip and remove the No. 2 ventilation hose from the cylinder head cover sub-assembly.


Hide 43.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A401310

Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the No. 1 ventilation case.


b.
A426577

Remove the bolt and wire harness clamp bracket from the camshaft housing sub-assembly.


Hide 44.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A480778

Using an E8 "TORX" socket wrench, remove the stud bolt from the timing chain cover assembly.