1.CHECK INJECTOR COMPENSATION CODE
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
58521D
3.REMOVE ENGINE SERVICE HOLE COVER MAT
Remove the engine service hole cover mat.
58410
4.REMOVE ENGINE SERVICE HOLE COVER
Detach the 2 hooks, 2 guides and remove the engine service hole cover.
58734B
5.REMOVE REAR ENGINE SERVICE COVER WEATHERSTRIP
Remove the rear engine service cover weatherstrip.
58420
6.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY
Turn the knob to detach the hook, detach the 2 guides and remove the No. 2 engine service hole cover assembly.
| *a | Knob |
58123A
7.REMOVE SHIFT AND SELECT LEVER SUPPORT WITH BOOTS
Remove the shift lever knob sub-assembly.
Remove the transmission cover mat.
Remove the 4 bolts and remove the shift and select lever support with boots.
33506F
8.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY
Remove the nut, washer plate, 3 clips and disconnect the select cable and shift cable.
| *1 | Washer Plate |
Remove the 4 bolts and remove the floor shift control shift lever retainer sub-assembly.
58701A
9.REMOVE FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY
Remove the nut and disconnect the shift wire clamp from the front engine service cover panel sub-assembly.
Remove the 3 bolts and front engine service cover panel sub-assembly.
51441D
10.REMOVE NO. 1 ENGINE UNDER COVER
51445D
11.REMOVE ENGINE UNDER COVER BRACKET RH
51446C
12.REMOVE ENGINE UNDER COVER BRACKET LH
53712C
13.REMOVE FRONT FENDER APRON LH
53711C
14.REMOVE FRONT FENDER APRON RH
15.DRAIN ENGINE OIL
16.DRAIN ENGINE COOLANT
17410
17.REMOVE FRONT EXHAUST PIPE ASSEMBLY
46700
18.REMOVE EXHAUST RETARDER ASSEMBLY
25608
19.REMOVE EGR COOLER SUB-ASSEMBLY
17201
20.REMOVE TURBOCHARGER SUB-ASSEMBLY
16361
21.REMOVE FAN
17030
22.REMOVE AIR HOSE ASSEMBLY
16571
23.DISCONNECT INLET RADIATOR HOSE
Slide the clamp and disconnect the inlet radiator hose.
16400
24.REMOVE RADIATOR ASSEMBLY
87245A
25.DISCONNECT INLET HEATER WATER HOSE A
Slide the clamp and disconnect the inlet heater water hose A.
16577C
26.REMOVE RADIATOR PIPE
Remove the 2 bolts and radiator pipe.
Remove the O-ring.
88320
27.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Disconnect the connector.
Remove the 4 bolts and disconnect the cooler compressor assembly.
44379A
28.REMOVE NO. 2 OIL RESERVOIR BRACKET
Remove the 3 bolts and No. 2 oil reservoir bracket.
44310
29.DISCONNECT VANE PUMP ASSEMBLY
Remove the 2 bolts and disconnect the vane pump assembly.
Remove the O-ring.
44774
30.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Slide the clamp and disconnect the union to connector tube hose.
23271F
31.DISCONNECT FUEL HOSE
Slide the 2 clamps and disconnect the 2 fuel hoses.
27020
32.REMOVE GENERATOR ASSEMBLY
28100
33.REMOVE STARTER ASSEMBLY
33110
34.REMOVE MANUAL TRANSMISSION ASSEMBLY
45450
35.DISCONNECT STEERING RELAY ROD ASSEMBLY
51202D
36.REMOVE FRONT LOWER SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Remove the 2 bolts, 4 through bolt, nuts and front lower suspension crossmember sub-assembly.
While fixing the nut in place, loosen and remove the through bolt.
82121
37.DISCONNECT ENGINE WIRE
Remove the 2 bolts and disconnect the engine wire from the No. 1 engine hanger.
Remove the 3 bolts and nut, and disconnect the engine wire from the engine assembly.
| *a | LH Side |
| *b | RH Side |
11000
38.REMOVE ENGINE ASSEMBLY
Using an engine lifter, support the engine and height adjustments or plate lift attachments.
Place the height adjustments or plate lift attachments so that the engine assembly is level.
As the engine assembly is very heavy, be sure to support it securely.
Remove the 2 nuts and washer.
Remove the 4 bolts and front No. 1 engine mounting bracket LH.
Remove the engine mounting stabilizer and front engine mounting insulator.
Remove the 2 nuts and washer.
Remove the 4 bolts and front No. 1 engine mounting bracket RH.
Remove the engine mounting stabilizer and front engine mounting insulator.
Remove the engine assembly.
When removing the engine assembly be careful not to damage any wire harnesses.
39.INSTALL ENGINE STAND
Attach an engine sling device and hang the engine assembly with a chain block.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
Install the engine assembly to an engine stand with bolts.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
Remove the 2 bolts and generator bracket.
Remove the 2 bolts and No. 1 engine hanger.
12180E
40.REMOVE OIL FILLER CAP ASSEMBLY
Remove the oil filler cap sub-assembly.
11201
41.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 2 bolts and cylinder head cover sub-assembly.
11202F
42.REMOVE CYLINDER HEAD COVER CUSHION RUBBER
Remove the cylinder head cover cushion rubber from the cylinder head cover sub-assembly.
11247
43.REMOVE CYLINDER HEAD COVER STAY
Remove the 2 cylinder head cover stays from the cylinder head cover sub-assembly.
11202D
44.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY
Disconnect the 5 connectors and remove the wire harness.
|
Bolt |
|
Connector |
Remove the 2 bolts and remove the No. 2 cylinder head cover sub-assembly.
11228
45.REMOVE CYLINDER HEAD COVER CUSHION
Remove the 2 cylinder head cover cushions from the No. 2 cylinder head cover sub-assembly.
11213
46.REMOVE CYLINDER HEAD COVER GASKET
Remove the cylinder head cover gasket from the No. 2 cylinder head cover sub-assembly.
25620
47.REMOVE EGR VALVE ASSEMBLY
26100
48.REMOVE DIESEL THROTTLE BODY
83420
49.REMOVE WATER TEMPERATURE SENDER GAGE ASSEMBLY
11301K
50.REMOVE CRANKSHAFT POSITION SENSOR
11301M
51.REMOVE CAMSHAFT POSITION SENSOR
16630G
52.REMOVE IDLER PULLEY ASSEMBLY
Remove the 2 bolts and idler pulley assembly.
88440B
53.REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)
Remove the 3 bolts and idle pulley assembly with bracket.
88431A
54.REMOVE NO. 2 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
Remove the 5 bolts and No. 2 compressor mounting bracket.
88431
55.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
Remove the 2 bolts and No. 1 compressor mounting bracket.
16331A
56.REMOVE THERMOSTAT
16333
57.REMOVE WATER OUTLET HOUSING
Remove the 3 bolts and water outlet housing.
87208L
58.REMOVE WATER PIPE SUB-ASSEMBLY
Remove the 3 bolts, water pipe sub-assembly and O-ring.
59.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Slide the clamp and disconnect the water hose.
Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly.
16206
60.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 6 bolts, water by-pass pipe sub-assembly and 6 O-rings.
16100
61.REMOVE ENGINE WATER PUMP ASSEMBLY
23741B
62.REMOVE INJECTION PIPE CLAMP
63.REMOVE INJECTION PIPE SUB-ASSEMBLY
23670
64.REMOVE INJECTOR ASSEMBLY
11177
65.REMOVE INJECTION NOZZLE SEAT GASKET
23811
66.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE
23810A
67.REMOVE COMMON RAIL ASSEMBLY
22100
68.REMOVE FUEL SUPPLY PUMP ASSEMBLY
23803H
69.REMOVE FUEL RETURN PIPE SUB-ASSEMBLY
70.REMOVE NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY
23802E
71.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY
Remove the 2 union bolts, the 2 gaskets and the No. 4 fuel pipe sub-assembly.
23803H
72.REMOVE FUEL RETURN PIPE SUB-ASSEMBLY
Remove the union bolt, gasket and fuel return pipe sub-assembly.
23300D
73.REMOVE DIESEL FUEL FILTER ASSEMBLY
23310
74.REMOVE UPPER FUEL FILTER BODY
Remove the 2 bolts and upper fuel filter body.
19971E
75.REMOVE VACUUM PIPE
Remove the nut and pipe clamp.
Remove the union bolt, vacuum pipe and 2 gaskets.
29601B
76.REMOVE VACUUM PUMP OIL PIPE SUB-ASSEMBLY
Remove the 3 union bolts and vacuum pump oil pipe sub-assembly and 3 gaskets.
29300
77.REMOVE VACUUM PUMP ASSEMBLY
Remove the 2 nuts, vacuum pump assembly and O-ring.
23849G
78.REMOVE FUEL PIPE SUPPORT
Remove the bolt and fuel pipe support.
23264D
79.REMOVE FUEL FILTER BRACKET
Remove the 2 bolts and fuel filter bracket.
15701C
80.REMOVE OIL COOLER COVER SUB-ASSEMBLY
17107
81.REMOVE EXHAUST MANIFOLD HEAT INSULATOR SUB-ASSEMBLY
17141
82.REMOVE EXHAUST MANIFOLD
17111
83.REMOVE INTAKE MANIFOLD
23809L
84.REMOVE FUEL PIPE SUPPORT SUB-ASSEMBLY
Remove the 2 bolts and fuel pipe support sub-assembly.
23849G
85.REMOVE FUEL PIPE SUPPORT
Remove the 2 bolts and fuel pipe support.