Home › Engine / Hybrid System › N04C-VQ (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073144 N04C-VQ ENGINE MECHANICAL _0355909 CYLINDER HEAD GASKET A

N04C-VQ ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.

Install a new cylinder head gasket.

NOTICE:

Always use a new cylinder head gasket after cleaning the surface of the cylinder head sub-assembly, cylinder block sub-assembly and keep them free of dirt, water and grease.



Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

a.

Install the 8 valve lifters.

NOTICE:

Be sure to install the removed valve lifter to its original location.



b.

Install the cylinder head sub-assembly over the straight pin on the cylinder block sub-assembly.

HINT:

Since the cylinder head bolts are unique to this engine, do not substitute them with ordinary bolts.



c.

Apply a light coat of engine oil to the threads of the cylinder head bolts.


d.

Step 1:

i.
A254649E01
1.031,0.448 1.177,0.635 0.146,0.188 10 true 8 0.396,0.448 0.594,0.625 0.198,0.177 10 true 16 1.667,0.438 1.802,0.615 0.135,0.177 10 true 1 2.26,0.438 2.417,0.615 0.156,0.177 10 true 9 2.833,0.448 3.052,0.604 0.219,0.156 10 true 17 0.708,0.271 0.927,0.458 0.219,0.188 10 false 12 1.365,0.26 1.583,0.448 0.219,0.188 10 false 4 1.979,0.271 2.198,0.458 0.219,0.188 10 false 5 2.552,0.26 2.771,0.448 0.219,0.188 10 false 13 0.406,1.729 0.604,1.906 0.198,0.177 10 false 15 0.729,1.885 0.927,2.063 0.198,0.177 10 false 11 1.063,1.719 1.26,1.896 0.198,0.177 10 false 7 1.375,1.885 1.573,2.063 0.198,0.177 10 false 3 1.677,1.708 1.875,1.885 0.198,0.177 10 false 2 1.99,1.875 2.188,2.052 0.198,0.177 10 false 6 2.25,1.708 2.448,1.885 0.198,0.177 10 false 10 2.552,1.865 2.75,2.042 0.198,0.177 10 false 14 2.823,1.708 3.021,1.885 0.198,0.177 10 false 18

Uniformly install and tighten the cylinder head bolts in the order shown in the illustration.

Torque:

60 N*m (612 kgf*cm, 44 ft.*lbf)




e.

Step 2:

i.

Mark the front side of each cylinder head bolt head with paint.


ii.

Tighten the cylinder head bolts 90°.



f.

Step 3:

i.

Tighten the cylinder head bolts an additional 90°.


ii.

Check that the paint marks are now at a 180° angle to the front.



g.
A254650E01
0.76,0.948 0.906,1.115 0.146,0.167 10 true 3 1.375,0.948 1.521,1.115 0.146,0.167 10 true 1 1.99,0.938 2.135,1.104 0.146,0.167 10 true 2 2.594,0.948 2.74,1.115 0.146,0.167 10 true 4

Uniformly install and tighten the cylinder head bolts in the order shown in the illustration.

Torque:

55 N*m (561 kgf*cm, 41 ft.*lbf)



Hide 13901 5.INSTALL NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

Hide 7.INSTALL NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY

Hide 16206 8.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 9.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 87208L 10.INSTALL WATER PIPE SUB-ASSEMBLY

Hide 87245A 12.CONNECT INLET HEATER WATER HOSE A

Hide 23670 14.INSTALL INJECTOR ASSEMBLY

Hide 17141 15.INSTALL EXHAUST MANIFOLD

Hide 27020 16.INSTALL GENERATOR ASSEMBLY

Hide 16400 17.INSTALL RADIATOR ASSEMBLY

Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 58701A 21.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

Hide 24.INSPECT FOR EXHAUST GAS LEAK

Hide 51446C 25.INSTALL ENGINE UNDER COVER BRACKET LH

Hide 51445D 26.INSTALL ENGINE UNDER COVER BRACKET RH

Hide 51441D 27.INSTALL NO. 1 ENGINE UNDER COVER

Hide 28.CHECK INJECTOR COMPENSATION CODE