Home › Engine / Hybrid System › 2AZ-FE ENGINE MECHANICAL › CYLINDER HEAD › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059548 2AZ-FE ENGINE MECHANICAL _0291834 CYLINDER HEAD A

2AZ-FE ENGINE MECHANICAL  CYLINDER HEAD  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Check whether the engine is TMC made or not by referring to the following illustration.

U188506E01
3.93,0.096 4.173,0.285 0.243,0.189 10 *B 0.339,0.096 0.588,0.285 0.249,0.189 10 *A 2.471,0.822 2.640,0.977 0.169,0.154 10 *1 2.471,0.932 2.045,1.143 false 6.069,0.84 6.239,0.994 0.169,0.154 10 *1 6.069,0.964 5.767,1.216 false 4.061,1.835 4.230,1.989 0.169,0.154 10 *2 6.342,1.937 6.511,2.092 0.169,0.154 10 *3 4.233,1.894 4.774,1.749 false 6.33,2.025 5.924,2.109 false

Text in Illustration
*A for TMC Made Engine *B except TMC Made Engine
*1 Engine Oil Level Dipstick Guide *2 Water Inlet Housing
*3 Water Inlet Housing Drain Cock Assembly - -


PROCEDURE

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53292A 3.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 4.REMOVE FRONT WHEEL RH

Hide 51441 5.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53701 6.REMOVE FRONT FENDER APRON RH

Hide 9.REMOVE COWL TOP OUTER PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

a.

Remove the cowl top outer panel with windshield wiper motor and link (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 23250 12.REMOVE FUEL DELIVERY PIPE WITH INJECTOR ASSEMBLY

a.

Remove the fuel delivery pipe with injector assembly (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL INJECTOR>REMOVAL).


Hide 17111 13.REMOVE INTAKE MANIFOLD

a.

Remove the intake manifold (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>KNOCK SENSOR>REMOVAL).

NOTICE:

Do not forcibly pull out the intake manifold, as the gap between the body and engine is narrow. Make sure not to scratch the contact surfaces of the intake manifold port to cylinder head.


HINT:

When replacing the intake manifold, remove the engine assembly (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL).



Hide 17135A 14.REMOVE INTAKE MANIFOLD INSULATOR

Hide 87245A 15.DISCONNECT HEATER WATER INLET HOSE

a.

Disconnect the heater water inlet hose.

A394015E01
0.292,0.188 0.667,0.427 0.375,0.24 12 false *A 4.031,0.135 4.406,0.375 0.375,0.24 12 false *B

Text in Illustration
*A for Automatic Transaxle
for CVT (w/ Air Cooled Transmission Oil Cooler)
*B for CVT (w/o Air Cooled Transmission Oil Cooler)


Hide 15301 18.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 11452 19.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE (for TMC Made Engine)

a.
A112218

Remove the bolt and guide.


b.

Remove the O-ring from the guide.


Hide 11452 20.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE (except TMC Made Engine)

a.
A161764

Remove the bolt and guide.


b.

Remove the O-ring from the guide.


Hide 17118 21.REMOVE MANIFOLD STAY

a.
A112193

Remove the bolt, nut and stay.


Hide 17139 22.REMOVE NO. 2 MANIFOLD STAY

a.
A112192

Remove the bolt, nut and stay.


Hide 17167 23.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A112189

Remove the 4 bolts and heat insulator.


Hide 25051 24.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.
A112190

Remove the 5 nuts, manifold converter and gasket.


Hide 16571C 25.DISCONNECT NO. 1 RADIATOR HOSE

a.

Disconnect the hose from the cylinder head.


Hide 51217A 26.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

Hide 16361A 27.REMOVE FAN AND GENERATOR V BELT

Hide 11201 34.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 16620 35.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11301K 36.REMOVE CRANKSHAFT POSITION SENSOR (for TMC Made Engine)

Hide 11301K 37.REMOVE CRANKSHAFT POSITION SENSOR (except TMC Made Engine)

Hide 39.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A098345E32
2.167,2.344 2.625,2.427 false 1.073,0.677 1.052,0.135 1.052,0.135 2.583,0.656 false 1.073,1.292 1.052,1.833 1.052,1.833 2.594,1.042 false 0.177,0.063 1.01,0.438 0.833,0.375 10 true Timing Mark 0.208,1.76 1.01,1.969 0.802,0.208 10 false Timing Mark 2.677,2.323 3.188,2.5 0.51,0.177 10 false Groove

Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.


b.

Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.

If not, turn the crankshaft by 1 revolution (360°) to align the timing marks as above.


Hide 13512 40.REMOVE NO. 2 CAMSHAFT

a.
A098172E08
0.948,0.146 1.01,0.146 1.01,0.146 1.031,0.344 false 2.542,0.125 2.448,0.125 2.448,0.125 2.521,0.365 false 1.031,0.417 0.583,1.219 false 1.073,0.781 0.583,1.219 false 2.448,0.51 2.885,1.219 false 2.073,1.5 2.521,1.74 false 0.083,0.021 0.802,0.188 0.719,0.167 10 false Paint Mark 2.573,0.021 3.271,0.188 0.698,0.167 10 false Paint Mark 0.083,1.198 0.896,1.448 0.813,0.25 10 false Timing Mark 2.438,1.198 3.25,1.448 0.813,0.25 10 false Timing Mark 2.594,1.656 3.146,1.844 0.552,0.188 10 false Groove

Place paint marks on the chain in alignment with the timing marks on the camshaft timing gear and camshaft timing sprocket.


b.
A098348

Remove the 2 nuts, tensioner and gasket.


c.
U150644E02
2.604,0.354 2.896,1.177 2.896,1.177 2.896,1.271 true 0.781,0.115 1.281,0.281 0.5,0.167 10 false Loosen 2.729,1.281 3.073,1.458 0.344,0.177 10 false Hold

While holding the camshaft with a wrench, loosen the camshaft timing set bolt.


d.
A098174E19
0.635,1.031 0.146,1.031 false 0.625,1.385 0.135,1.385 false 1.01,1.063 1.01,0.229 false 1.604,1.052 1.604,0.219 false 2.177,1.052 2.177,0.219 false 2.76,1.052 2.76,0.219 false 1.042,1.313 1.188,1.417 false 1.625,1.333 1.771,1.427 false 2.219,1.333 2.365,1.427 false 2.813,1.333 2.948,1.427 false 0.021,0.938 0.167,1.125 0.146,0.188 10 false 1 0.979,0.01 1.125,0.198 0.146,0.188 10 false 5 1.24,1.375 1.385,1.563 0.146,0.188 10 true 6 2.406,1.375 2.552,1.563 0.146,0.188 10 true 8 1.802,1.375 2,1.583 0.198,0.208 10 true 10 2.99,1.375 3.135,1.563 0.146,0.188 10 true 4 1.552,0.01 1.698,0.198 0.146,0.188 10 false 9 2.135,0.01 2.281,0.198 0.146,0.188 10 false 7 2.708,0.01 2.854,0.198 0.146,0.188 10 false 3 0.021,1.292 0.167,1.479 0.146,0.188 10 false 2

Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.


e.

Remove the 5 bearing caps.


f.
A052473

While holding the No. 2 camshaft by hand, remove the camshaft timing sprocket set bolt.


g.

Remove the camshaft timing sprocket from the No. 2 camshaft with the timing chain wrapped on the sprocket.


h.

Remove the camshaft timing sprocket from the timing chain.


Hide 13511 41.REMOVE CAMSHAFT

a.
A098175E07
2.979,0.604 3.219,0.792 0.24,0.188 2.365,0.604 2.604,0.792 0.24,0.188 1.802,0.552 2.042,0.771 0.24,0.219 1.219,0.604 1.458,0.792 0.24,0.188 0.698,0.74 0.156,0.74 true 0.698,1.094 0.156,1.094 true 1.073,1.063 1.073,1.885 true 1.646,1.063 1.646,1.885 true 2.208,1.052 2.208,1.875 true 2.781,1.052 2.781,1.823 true 1.271,0.667 1.115,0.76 false 1.844,0.677 1.688,0.771 false 2.396,0.667 2.24,0.76 false 2.979,0.688 2.823,0.781 false 0.031,0.635 0.208,0.813 0.177,0.177 10 false 1 0.031,0.99 0.208,1.167 0.177,0.177 10 false 2 1.031,1.927 1.208,2.104 0.177,0.177 10 false 6 1.302,0.594 1.479,0.771 0.177,0.177 10 false 5 1.875,0.594 2.052,0.771 0.177,0.177 10 false 9 2.438,0.594 2.615,0.771 0.177,0.177 10 false 7 3.021,0.594 3.198,0.771 0.177,0.177 10 false 3 2.156,1.927 2.333,2.104 0.177,0.177 10 false 8 1.542,1.927 1.719,2.104 0.177,0.177 10 false 10 2.729,1.854 2.906,2.031 0.177,0.177 10 false 4

Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.


b.

Remove the 5 bearing caps.


c.

Remove the camshaft and camshaft timing gear while holding the timing chain by hand.


d.
A056228

Tie the timing chain with a string as shown in the illustration.

NOTICE:

Be careful not to drop anything inside the timing chain cover.



Hide 12315A 43.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11302 44.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 19315 45.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 13561 48.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 49.REMOVE CHAIN SUB-ASSEMBLY

Hide 11101J 50.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 13050 51.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A090848E07
1.875,0.5 3.073,0.667 1.198,0.167 10 false Advance Side Port

Clamp the camshaft in a vise, and make sure that the camshaft timing gear does not rotate.


b.

Cover all the oil ports with vinyl tape except the advance side port shown in the illustration.


c.
A031032

Apply air pressure of 100 kPa (1.0 kgf/cm2, 14 psi) to the oil path, then turn the camshaft timing gear in the advance direction (counterclockwise) by hand.

CAUTION:

Cover the paths with a shop rag to avoid oil splashes.


HINT:

Depending on the air pressure, the camshaft timing gear will turn to the advance angle side without applying force by hand. Also, under the condition that the pressure is difficult to apply because of air leakage from the port, the lock pin may be difficult to release.



d.
A032639

Remove the flange bolt of the camshaft timing gear.

NOTICE:
·

Be sure not to remove the other 4 bolts.


·

When reusing the camshaft timing gear, release the straight lock pin first, then install the gear.




Hide 11101 52.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
F050595E15
0.365,0.073 0.51,0.229 0.146,0.156 10 false 1 0.979,0.073 1.125,0.229 0.146,0.156 10 false 5 1.594,0.073 1.74,0.229 0.146,0.156 10 false 9 2.198,0.073 2.344,0.229 0.146,0.156 10 false 7 2.823,0.073 2.969,0.229 0.146,0.156 10 false 3 2.823,1.854 2.969,2.01 0.146,0.156 10 false 4 2.198,1.854 2.344,2.01 0.146,0.156 10 false 6 1.552,1.854 1.76,2.01 0.208,0.156 10 false 10 0.99,1.854 1.135,2.01 0.146,0.156 10 false 8 0.375,1.854 0.521,2.01 0.146,0.156 10 false 2

Using several steps, uniformly loosen and remove the 10 cylinder head bolts and 10 plate washers with a 10 mm bi-hexagon wrench in the sequence shown in the illustration.

NOTICE:

Head warpage or cracking could result from removing the bolts in the wrong order.



b.
A126930

Using a screwdriver, pry between the cylinder head and cylinder block, and remove the cylinder head.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and cylinder block.



Hide 11115 53.REMOVE CYLINDER HEAD GASKET

A126929