Home › Brake › BRAKE › BRAKE BOOSTER(for 2GR-FE) › 2014.09–2016.05
RM24M0E _54 Brake _059558 BRAKE _0291883 BRAKE BOOSTER(for 2GR-FE) A

BRAKE  BRAKE BOOSTER(for 2GR-FE)  INSTALLATION  


PROCEDURE

Hide 44696 1.INSTALL CHECK VALVE GROMMET

a.

Install the check valve grommet to the brake booster assembly.


Hide 44730 2.INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY

a.

Install the brake vacuum check valve to the brake booster assembly.


Hide 44785 3.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster assembly.


Hide 47264D 4.INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.

Install the push rod clevis to the brake booster assembly.


b.

Temporarily tighten the push rod clevis lock nut.

HINT:

The push rod clevis lock nut will be tightened to a torque specification in the "CHECK AND ADJUST BRAKE PEDAL HEIGHT" procedures.



Hide 44610 5.INSTALL BRAKE BOOSTER ASSEMBLY

a.
C158086

Install the brake booster assembly with the 4 nuts.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 11101J 6.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for RHD)

a.
C140018

Apply engine oil to a new O-ring, and install it to the camshaft timing oil control valve assembly.


b.

Install the camshaft timing oil control valve assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 88 in.*lbf)


Hide 7.INSTALL WIRE HARNESS (for LHD)

a.
C158097

Install the wire harness to the body with the nut and 2 bolts.


Hide 8.INSTALL WIRE HARNESS (for RHD)

a.
C140027

Install the wire harness to the engine assembly with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the 3 connectors.


Hide 9.INSTALL BRAKE LINE (for LHD)

a.
C158095

Install the brake line to the body with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
C158092

Engage the 5 clamps.


c.
C158101E02
2.213,2.452 2.438,2.615 0.225,0.163 10 *a

Using a union nut wrench, connect the 4 brake lines.

Text in Illustration
*a Torque Wrench Fulcrum Length

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length for the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):

14 N*m (142 kgf*cm, 10 ft.*lbf)




d.
C311048E02
2.531,2.604 2.01,1.99 true 1.656,2 1.25,2.74 true 1.604,1.76 1.938,1.063 true 1.75,1.76 2.229,1.323 true 1.906,1.76 2.427,1.573 true 2.073,1.802 2.458,1.906 true 2.563,2.573 2.792,2.76 0.229,0.188 10 true *a 1.146,2.76 1.375,2.948 0.229,0.188 10 true *b 1.917,0.906 2.146,1.094 0.229,0.188 10 false *c 2.219,1.177 2.448,1.365 0.229,0.188 10 false *d 2.448,1.469 2.677,1.656 0.229,0.188 10 true *e 2.49,1.865 2.719,2.052 0.229,0.188 10 true *f 0.729,0.313 0.958,0.5 0.229,0.188 10 false *g

Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.

Text in Illustration
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH
*g Torque Wrench Fulcrum Length


e.

Using a union nut wrench, fully tighten the 2 brake lines (*a, *b).

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length for the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):

18 N*m (184 kgf*cm, 13 ft.*lbf)




f.

Using a union nut wrench, fully tighten the 4 brake lines (*c, *d, *e, *f).

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length for the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):

14 N*m (142 kgf*cm, 10 ft.*lbf)




Hide 10.INSTALL BRAKE LINE (for RHD)

a.
C140017

Engage the 4 clamps and install the 2 brake lines.


Hide 11.CONNECT VACUUM HOSE

a.

Connect the vacuum hose to the brake vacuum check valve assembly with the clip.


Hide 47264A 12.INSTALL PUSH ROD PIN

a.
C308856

Apply lithium soap base glycol grease to the push rod pin.

Text in Illustration
V100135

Lithium Soap Base Glycol Grease


b.

Install the push rod pin to the push rod clevis.

NOTICE:

The push rod pin must be installed as shown in the illustration.



c.

Install a new clip to the push rod pin.

NOTICE:

The clip must be installed as shown in the illustration.


HINT:

Only the clip in the illustration will be supplied.



Hide 47201 13.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for LHD)

Hide 47201 14.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for RHD)

Hide 73900 15.INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55432B 16.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Driver Side Knee Airbag)

Hide 55432B 17.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/ Driver Side Knee Airbag)

Hide 55606 18.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55042B 20.INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55660 21.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

Hide 55420A 22.INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER ASSEMBLY

Hide 17190 23.INSTALL INTAKE AIR SURGE TANK ASSEMBLY (for RHD)

Hide 24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 16470 25.INSTALL RADIATOR RESERVOIR TANK ASSEMBLY (for RHD)

Hide 51442 28.INSTALL NO. 2 ENGINE UNDER COVER (for RHD)

Hide 11209 29.INSTALL V-BANK COVER SUB-ASSEMBLY (for RHD)

Hide 53292A 30.INSTALL UPPER RADIATOR SUPPORT SEAL (for RHD)

Hide 33.INSTALL FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR LINK

Hide 34.INSTALL BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET

Hide 55781F 35.INSTALL COWL TOP VENTILATOR LOUVER

Hide 53867H 36.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 37.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 38.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 39.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 85192 40.INSTALL FRONT WIPER ARM HEAD CAP

Hide 41.BLEED BRAKE SYSTEM

Hide 42.INSPECT AND ADJUST BRAKE PEDAL

Hide 43.INSPECT SRS WARNING LIGHT