P1603 Engine Stall History
Diagnostic trouble codes · Vehicles built Dec 2015 – Mar 2016
Also covers:
- P1605 Rough Idling
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
- P1603
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle has ran out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P1603 |
After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the ignition switch being operated for 0.5 seconds or more (1 trip detection logic). |
|
- P1605
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P1605 |
After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic). |
|
INSPECTION PROCEDURE
- HINT:
- In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
- If any other DTCs are output, perform troubleshooting for those DTCs first.
- Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.
Symptom
Suspected Area
Engine vibration occurs and engine stops
Air-fuel ratio abnormal
Engine stops with no engine vibration
Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed
Insufficient air volume
Rough idling after engine started
Air-fuel ratio abnormal, abnormal combustion
- Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
- When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here).
- When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. The ECM stores DTC P1605 first. Therefore, 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.
- When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
- Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
- Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.
- When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
- In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
- Inspection flow:
- Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.
- P1603:


- If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air-fuel ratio, etc.
- If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.
- If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.
- If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
- If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
- If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
| Vehicle State |
Engine Speed |
Suspected Area |
Primary Parts to Inspect |
Procedure |
|
| Idling or decelerating |
Slowly decreases and engine stalls |
Ignition system abnormal |
Igniter abnormal |
|
10, 38, 52 |
| Air-fuel ratio abnormal |
Air suction |
|
5 to 9 |
||
| Sensor malfunction (value from sensor too lean) |
|
11 to 23 |
|||
| Sensor malfunction (value from sensor too rich) |
39 to 51 |
||||
| Fuel supply problem |
|
24 to 37 |
|||
| Intake air volume insufficient |
Problem with air passage |
|
53 to 55 |
||
| Excessive valve overlap |
|
56 to 57 |
|||
| Ignition timing incorrect |
Does not operate as expected |
|
58 to 62 |
||
| Rapidly decreases and engine stalls |
Ignition and injection stops (electrical system malfunction) |
Power temporarily cut |
|
63, 64 |
|
| External part malfunctioning |
Increase in load |
|
65 to 68 |
||
| Accelerating |
- |
Crankshaft position sensor, camshaft position sensor malfunction |
Power temporarily cut |
|
1 |
| Mass air flow meter |
Foreign matter adhesion |
|
69 to 72 |
||
| Ignition and injection stops (electrical system malfunction) |
Power temporarily cut |
|
73, 74 |
||
| Fuel supply problem |
Fuel leak, clog |
|
75 to 79 |
||
- P1605:


- If the engine speed decreased slowly, there may have been a decrease in torque due an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.
- If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
- If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
- If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
| Engine Speed |
Suspected Area |
Primary Parts to Inspect |
Procedure |
|
| Slowly decreases and engine stalls |
Ignition system abnormal |
Igniter abnormal |
|
10, 38, 52 |
| Air-fuel ratio abnormal |
Air suction |
|
5 to 9 |
|
| Sensor malfunction (value from sensor too lean) |
|
11 to 23 |
||
| Sensor malfunction (value from sensor too rich) |
39 to 51 |
|||
| Fuel supply problem |
|
24 to 37 |
||
| Intake air volume insufficient |
Problem with air passage |
|
53 to 55 |
|
| Excessive valve overlap |
|
56 to 57 |
||
| Ignition timing incorrect |
Does not operate as expected |
|
58 to 62 |
|
| Rapidly decreases and engine stalls |
Ignition and injection stops (electrical system malfunction) |
Power temporarily cut |
|
63, 64 |
| External part malfunctioning |
Increase in load |
|
65 to 68 |
|
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs (Click here).
Result Result
Proceed to
Only DTC P1603 and P1605 are output
A
DTCs other than P1603 and P1605 are output
B
|
|
||||
| A | |
| 2. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
- OK:
- Immobiliser Fuel Cut is OFF.
Result Result
Proceed to
Abnormal
A
Normal
B
|
|
||||
| A | |
| 3. CHECK ENGINE IMMOBILISER SYSTEM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine.
Idle the engine
Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Communication and Immobiliser Fuel Cut.
Check the Data List indication.
Result Data List Item
Result
Immobiliser Communication
ON
Immobiliser Fuel Cut
OFF
|
|
||||
| OK | |
| 4. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Problem Symptom
Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
Closed Throttle Position SW
Engine Speed
Total of Short FT and Long FT
When idling or decelerating, engine speed slowly decreases and engine stalls
All 5 sets of freeze frame data are ON
Decreases slowly*1
All 5 sets of freeze frame data are +15% or more*2
- Air suction
- Sensor malfunction (value from sensor too lean)
- Fuel supply problem
A
At least 1 of the 5 sets of freeze frame data is -15% or less*3
Sensor malfunction (value from sensor too rich)
B
All 5 sets of freeze frame data are from -15% to +15%
- Intake air volume insufficient
- Ignition timing incorrect
C
When idling or decelerating, engine speed rapidly decreases and engine stalls
Decreases rapidly*1
-
- Injection stoppage, ignition stoppage
- Load from external parts
D
When accelerating or driving at constant speed, engine stalls*4
At least one is OFF
-
-
- Sensor malfunction
- Injection stoppage, ignition stoppage
- Fuel supply problem
E


- HINT:
- *1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.
Otherwise, the engine speed is considered to have decreased slowly.
- In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or more.
- In the freeze frame data, the engine speed at #5 is 120 rpm or less.
- *1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.
- If the vehicle speed is 30 km/h or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transmission. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
- *2: When a DTC is stored, feedback compensation increases because the air-fuel ratio is determined to be lean.
- *3: When a DTC is stored, feedback compensation decreases because the air-fuel ratio is determined to be rich.
- *4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.
- If the vehicle speed is 30 km/h or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transmission. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
- Air suction
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 5. CHECK AIR INDUCTION SYSTEM |
Check for air leakage in the air induction system [vacuum hose disconnection, cracks, damaged gaskets, etc.].
- HINT:
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
- If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
- OK:
- There is no air leakage.
|
|
||||
| OK | |
| 6. CHECK EVAP VSV |
Disconnect the vacuum hose (on the canister side) of the EVAP VSV.

Start the engine.
Idle the engine.
Disconnect the connector of the EVAP VSV.
Check if air flows through the EVAP VSV.
- OK:
- Air does not flow.
- HINT:
- When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).
|
|
||||
| OK | |
| 7. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Stop Light Switch
At least 1 of the 5 sets of freeze frame data is ON
Air suction from brake booster
A
All 5 sets of freeze frame data are OFF
-
B
|
|
||||
| A | |
| 8. READ VALUE USING INTELLIGENT TESTER (SHORT FT) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT #1.
Read value of the Data List items while depressing the brake pedal.
- Standard:
- Short FT #1 changes by +10% or less.
- HINT:
- When air leakage from the brake booster is present, the feedback compensation increases because the air-fuel ratio becomes lean.
|
|
||||
| OK | |
| Go to step 7 |
| 9. PERFORM DRIVE TEST |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT #1 and Long FT #1.
Read the values displayed on the tester.
- Standard:
Data List
Condition
Specified Condition
Short FT #1 + Long FT #1
The conditions of the vehicle are matched to those present when the problem occurs
-15 to +15%
|
|
||||
| OK | |
| 10. CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
|
||||
| OK | |
| 11. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Calculate Load
Below 90% of the current value of the vehicle*1
Mass air flow meter
A
AFS Voltage B1S1
3.3 V or higher*2
- Air fuel ratio sensor
- Wire harness or connector
B
- HINT:
- *1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.
- *2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.
- *1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.
- Air fuel ratio sensor
|
|
||||
| A | |
| 12. CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
Result Result
Proceed to
Visible foreign matter is not present
A
Visible foreign matter is present
B
Install the mass air flow meter.
|
|
||||
| A | |
| 13. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Condition
Specified Condition
A3-3 (VG) - D97-69 (VG)
Always
Below 1 Ω
A3-2 (E2G) - D97-92 (E2G)
Always
Below 1 Ω
A3-3 (VG) or D97-69 (VG) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 14. PERFORM DRIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Calculate Load.
Read the values displayed on the tester.
- Standard:
Data List
Specified Condition
Calculate Load
90 to 110% of the current value of the vehicle
Result Result
Proceed to
Abnormal
A
Normal
B
|
|
||||
| A | ||
| ||
| 15. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
- Standard:
Tester Display
Specified Condition
Control the Injection Volume (12%)
Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume (-12%)
Air fuel ratio sensor output voltage is higher than 3.4 V
Result Result
Proceed to
Abnormal
A
Normal
B
- HINT:
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
|
|
||||
| A | |
| 16. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR POWER SOURCE) |
![]() ![]() |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D33-2 (+B) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Air Fuel Ratio Sensor)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 17. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D33-1 (HA1A) - D97-104 (HA1A)
Always
Below 1 Ω
D33-3 (A1A+) - D97-103 (A1A+)
Always
Below 1 Ω
D33-4 (A1A-) - D97-126 (A1A-)
Always
Below 1 Ω
D33-1 (HA1A) or D97-104 (HA1A) - Body ground
Always
10 kΩ or higher
D33-3 (A1A+) or D97-103 (A1A+) - Body ground
Always
10 kΩ or higher
D33-4 (A1A-) or D97-126 (A1A-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 18. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Proceed to
Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp
Difference in temperature between each item is less than 10°C*1
A
Difference in temperature between each item is 10°C or more*2
B
- HINT:
- *1: A long time had elapsed after stopping the engine.
- *2: A long time had not elapsed after stopping the engine.
- *1: A long time had elapsed after stopping the engine.
|
|
||||
| A | |
| 19. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).


Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time
Range A
- Engine coolant temperature sensor
- Thermostat
A
Range B
Engine coolant temperature sensor
B
Range C
-
C
- HINT:
- This step is not directly related to engine stall.
- Engine coolant temperature sensor
|
|
||||
|
|
||||
| A | |
| 20. INSPECT THERMOSTAT |
- HINT:
- For the thermostat inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Abnormal |
A |
| Normal |
B |
- HINT:
- This step is not directly related to engine stall.
|
|
||||
| A | ||
| ||
| 21. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Coolant Temp
120°C or more
Engine coolant temperature sensor
A
Coolant Temp, Ambient Temperature
Engine coolant temperature is lower than outside temperature by 15°C or more
Engine coolant temperature sensor
Both freeze frame data items listed above
Values are other than above
-
B
|
|
||||
| A | |
| 22. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
- HINT:
- For the engine coolant temperature sensor inspection, refer to the following procedures (Click here).
|
|
||||
| OK | |
| 23. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE - ECM) |
Disconnect the engine coolant temperature connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Condition
Specified Condition
D32-2 - D97-64 (THW)
Always
Below 1 Ω
D32-1 - D97-72 (E2)
Always
Below 1 Ω
D32-2 or D97-64 (THW) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 24. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
EVAP (Purge) VSV
At least 1 of the 5 sets of freeze frame data is not 0%
EVAP VSV
A
All 5 sets of freeze frame data are 0%
-
B
- HINT:
- If the EVAP VSV is stuck closed, air-fuel ratio compensation by the EVAP VSV is incorrectly adjusted, and then the air-fuel ratio becomes lean and the engine may stall.
|
|
||||
| A | |
| 25. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL) |
Disconnect the vacuum hose (on the canister side) of the EVAP VSV.

Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
Operate the EVAP VSV and check the air flow.
- Standard:
Activate the VSV for Evap Control
Specified Condition
ON
Air flows
OFF
Air does not flow
Result Result
Proceed to
Abnormal
A
Normal
B
| *a |
VSV is ON |
| *b |
VSV is OFF |
| *c |
Air |
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Reconnect the vacuum hose of the EVAP VSV.
|
|
||||
| A | |
| 26. INSPECT EVAP VSV |
Inspect the EVAP VSV (Click here).
|
|
||||
| OK | |
| 27. CHECK HARNESS AND CONNECTOR (EVAP VSV POWER SOURCE) |
Disconnect the EVAP VSV connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D28-2 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to EVAP VSV)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 28. CHECK HARNESS AND CONNECTOR (EVAP VSV - ECM) |
Disconnect the EVAP VSV connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D28-1 - D97-62 (PRG)
Always
Below 1 Ω
D28-1 or D97-62 (PRG) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 29. CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
| NEXT | |
| 30. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine for 15 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / Data List / EVAP (Purge) VSV.
Read the value displayed on the tester.
- Standard:
Data List
Specified Condition
EVAP (Purge) VSV
Value other than 0% is displayed
Result Result
Proceed to
Abnormal
A
Normal
B
|
|
||||
| A | |
| 31. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL) |
Disconnect the vacuum hose (on the canister side) of the EVAP VSV.

Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
Operate the EVAP VSV and check the air flow.
- Standard:
Activate the VSV for Evap Control
Specified Condition
ON
Air flows
OFF
Air does not flow
Result Result
Proceed to
Abnormal
A
Normal
B
| *a |
VSV is ON |
| *b |
VSV is OFF |
| *c |
Air |
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Reconnect the vacuum hose of the EVAP VSV.
|
|
||||
| A | |
| 32. CHECK CONNECTOR CONNECTION CONDITION (ECM) |
Check the ECM connector connection condition.
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 33. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
- Standard:
Control the Fuel Pump / Speed
Specified Condition
ON
Operating sound heard
OFF
Operating sound not heard
Result Result
Proceed to
Abnormal
A
Normal
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
- If the fuel pump operating noise is abnormal, proceed to step 34.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | |
| 34. INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
|
||||
| OK | ||
| ||
| 35. CHECK FUEL SYSTEM |
Check the fuel system.
- Check the fuel pressure.
- Check the fuel pump operation.
- Check the fuel leaks.
- Check the fuel pressure.
- HINT:
- For the fuel system On-vehicle Inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Abnormal |
A |
| Normal |
B |
|
|
||||
| A | |
| 36. CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
Result Result
Proceed to
There is no foreign matter and no signs that fuel pump was stuck
A
There is foreign matter or signs that fuel pump was stuck
B
- HINT:
- If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.
|
|
||||
| A | |
| 37. CHECK FUEL SYSTEM |
Check the fuel system.
- Check the fuel pressure.
- Check the fuel pump operation.
- Check the fuel leaks.
- Check the fuel pressure.
- HINT:
- For the fuel system On-vehicle Inspection, refer to the following procedures (Click here).
|
|
||||
| OK | ||
| ||
| 38. CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
|
||||
| OK | |
| 39. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Calculate Load
110% or more of the current value of the vehicle*1
Mass air flow meter
A
AFS Voltage B1S1
Below 3.3 V*2
- Air fuel ratio sensor
- Harness and connector
B
Both freeze frame data items listed above
Values are other than above
-
C
- HINT:
- *1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.
- *2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is rich, the actual air-fuel ratio will become lean and the engine may stall.
- *1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.
- Air fuel ratio sensor
|
|
||||
|
|
||||
| A | |
| 40. CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
Result Result
Proceed to
Visible foreign matter is not present
A
Visible foreign matter is present
B
Install the mass air flow meter.
|
|
||||
| A | |
| 41. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Condition
Specified Condition
A3-3 (VG) - D97-69 (VG)
Always
Below 1 Ω
A3-2 (E2G) - D97-92 (E2G)
Always
Below 1 Ω
A3-3 (VG) or D97-69 (VG) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 42. PERFORM DRIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Calculate Load.
Read the values displayed on the tester.
- Standard:
Data List
Specified Condition
Calculate Load
90 to 110% of the current value of the vehicle
|
|
||||
| OK | |
| 43. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
- Standard:
Tester Display
Specified Condition
Control the Injection Volume (12%)
Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume (-12%)
Air fuel ratio sensor output voltage is higher than 3.4 V
Result Result
Proceed to
Abnormal
A
Normal
B
- HINT:
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
|
|
||||
| A | |
| 44. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR POWER SOURCE) |
![]() ![]() |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D33-2 (+B) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Air Fuel Ratio Sensor)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 45. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D33-1 (HA1A) - D97-104 (HA1A)
Always
Below 1 Ω
D33-3 (A1A+) - D97-103 (A1A+)
Always
Below 1 Ω
D33-4 (A1A-) - D97-126 (A1A-)
Always
Below 1 Ω
D33-1 (HA1A) or D97-104 (HA1A) - Body ground
Always
10 kΩ or higher
D33-3 (A1A+) or D97-103 (A1A+) - Body ground
Always
10 kΩ or higher
D33-4 (A1A-) or D97-126 (A1A-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 46. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Proceed to
Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp
Difference in temperature between each item is less than 10°C*1
A
Difference in temperature between each item is 10°C or more*2
B
- HINT:
- *1: A long time had elapsed after stopping the engine.
- *2: A long time had not elapsed after stopping the engine.
- *1: A long time had elapsed after stopping the engine.
|
|
||||
| A | |
| 47. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data (Click here).


Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time
Range A
- Engine coolant temperature sensor
- Thermostat
A
Range B
Engine coolant temperature
B
Range C
-
C
- HINT:
- This step is not directly related to engine stall.
- Engine coolant temperature sensor
|
|
||||
|
|
||||
| A | |
| 48. INSPECT THERMOSTAT |
- HINT:
- For the thermostat inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Abnormal |
A |
| Normal |
B |
- HINT:
- This step is not directly related to engine stall.
|
|
||||
| A | ||
| ||
| 49. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Coolant Temp
120°C or higher
Engine coolant temperature sensor
A
Coolant Temp, Ambient Temperature
Engine coolant temperature is lower than outside temperature by 15°C or more
Engine coolant temperature sensor
Both freeze frame data items listed above
Values are other than above
-
B
|
|
||||
| A | |
| 50. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
- HINT:
- For the engine coolant temperature sensor inspection, refer to the following procedures (Click here).
|
|
||||
| OK | |
| 51. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE - ECM) |
Disconnect the engine coolant temperature connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Condition
Specified Condition
D32-2 - D97-64 (THW)
Always
Below 1 Ω
D32-1 - D97-72 (E2)
Always
Below 1 Ω
D32-2 or D97-64 (THW) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 52. CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
|
||||
| OK | |
| 53. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Total of ISC Learning Value and ISC Feedback Value
Below 80% of the current value of the vehicle
Intake air volume insufficient
A
80% or more of the current value of the vehicle
B
|
|
||||
| A | |
| 54. CHECK AIR INDUCTION SYSTEM |
Check for air leakage in the air induction system [vacuum hose disconnection, cracks, damaged gaskets, etc.].
- HINT:
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
- If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
- OK:
- There is no air leakage.
|
|
||||
| OK | |
| 55. CHECK AIR INDUCTION SYSTEM |
Check the air induction system.
- Inspect the brake booster (Click here).
- Inspect the mass air flow meter (Click here).
- Check the PCV hose.
- Inspect the PCV valve (Click here).
- Inspect the EVAP VSV (Click here).
Result Result
Proceed to
Abnormal
A
Normal
B
- Inspect the brake booster (Click here).
|
|
||||
| A | ||
| ||
| 56. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT SYSTEM) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).
- HINT:
- When performing the Active Test, make sure the A/C is on and the shift lever is in P or N.
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
- OK:
Tester Operation
Specified Condition
OFF
Normal engine speed
ON
Soon after OCV switched from OFF to ON, engine idles roughly or stalls
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
- If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 57. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM) |
Disconnect the camshaft timing oil control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester connection
Condition
Specified condition
D78-2 - D97-74 (OC1+)
Always
Below 1 Ω
D78-1 - D97-96 (OC1-)
Always
Below 1 Ω
D78-2 or D97-74 (OC1+) - Body ground
Always
10 kΩ or higher
D78-1 - D97-96 (OC1-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 58. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
IGN Advance
Knock Correct Learn Value
Differs from the current value of the vehicle by 10 deg or more
Less than 3°CA
- Engine coolant temperature sensor
- Mass air flow meter
- Knock sensor
A
3°CA or more
-
B
Differs from the current value of the vehicle by less than 10 deg
-
-
- Engine coolant temperature sensor
|
|
||||
| A | |
| 59. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
- HINT:
- For the engine coolant temperature sensor inspection, refer to the following procedures (Click here).
|
|
||||
| OK | |
| 60. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE - ECM) |
Disconnect the engine coolant temperature connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Condition
Specified Condition
D32-2 - D97-64 (THW)
Always
Below 1 Ω
D32-1 - D97-72 (E2)
Always
Below 1 Ω
D32-2 or D97-64 (THW) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 61. INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR) |
Inspect the mass air flow meter (Click here).
- HINT:
- If the intake air temperature sent to the ECM is higher than the standard due to the mass air flow meter (intake air temperature sensor) malfunctioning, the ignition timing may become delayed.
|
|
||||
| OK | |
| 62. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance and Knock Correct Learn Value.
Read the values displayed on the tester.
Result Freeze Frame Data Item for DTC P1605
Proceed to
IGN Advance
Knock Correct Learn Value
Differs from the current value of the vehicle by 10 deg or more
Less than 3°CA
A
3°CA or more
B
Differs from the current value of the vehicle by less than 10 deg
-
- HINT:
- If the results of the checks performed in steps 54 to 62 were all normal and the sum of ISC Feedback Value and ISC Learning Value in the Data List is 120% of the normal value or more, check for carbon deposits in the throttle body assembly. If there are carbon deposits, clean them off to finish the troubleshooting procedure.
|
|
||||
| A | ||
| ||
| 63. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
Disconnect the ECM connector.
Turn the ignition switch to ON.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
D97-86 (#10) - D97-46 (E01)
Ignition switch ON
11 to 14 V
D97-85 (#20) - D97-46 (E01)
Ignition switch ON
11 to 14 V
D97-84 (#30) - D97-46 (E01)
Ignition switch ON
11 to 14 V
D97-83 (#40) - D97-46 (E01)
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to ECM)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 64. CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
|
||||
| OK | |
| 65. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
A/C Signal
Air Conditioner FB Val
Power Steering Signal
A/C Signal display does not change from OFF*3
Value displayed for Air Conditioner FB Val does not increase
Does not change from OFF
-
A*1
B*2
Changes from OFF to ON
Power steering system
A/C Signal display changes from OFF to ON
Value displayed for Air Conditioner FB Val increases
Changes from OFF to ON
Does not change from OFF
A/C system
C
- *1: for A/T
- *2: for M/T
- HINT:
- *3: Check not only the on/off state of the air conditioner, but also the change in air conditioner load.
- The normal value for the ISC compensation amount is engine displacement (liters) x 0.9.
- Even if the results are normal, the power steering system and/or A/C system may have been malfunctioning. If there are no problems with other parts, inspect the power steering system and/or A/C system.
- *3: Check not only the on/off state of the air conditioner, but also the change in air conditioner load.
- *1: for A/T
|
|
||||
|
|
||||
| A | |
| 66. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
Electrical Load Signal or Electric Load Feedback Val
Electric Load Feedback Val
Difference between Engine Speed and Turbine Speed
Vehicle Speed
Electrical Load Signal display changes from OFF to ON*1, or Value displayed for Electric Load Feedback Val increases*1
Value displayed for Electric Load Val changes
-
-
Electrical load signal circuit
A
Value displayed for Electric Load Val does not change
At least 1 of the 5 sets of freeze frame data is less than 100 rpm
Less than 30 km/h
A/T system
B
30 km/h or more
-
C
All 5 sets of freeze frame data are 100 rpm or more
-
-
C
Electrical Load Signal display does not change from OFF, or Value displayed for Electric Load Feedback Val does not increase
-
At least 1 of the 5 sets of freeze frame data is less than 100 rpm
Less than 30 km/h
A/T system
B
30 km/h or more
-
C
All 5 sets of freeze frame data are 100 rpm or more
-
-
C
- HINT:
- *1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
- The normal value for the ISC compensation amount is engine displacement (liters) x 0.9.
- Even if the results are normal, the electrical load signal system and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system and/or A/T system.
- *1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
|
|
||||
|
|
||||
| A | ||
| ||
| 67. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
P Position or N Position
Park/Neutral Position Switch
P and N position are both OFF in at least one data set
In D or R, NSW is ON
Park/neutral position switch
A
In D or R, NSW is OFF
A/T system
B
All 5 sets of freeze frame data are ON
-
-
C
- HINT:
- Even if the results are normal, the park/neutral position switch and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch and/or A/T system.
|
|
||||
|
|
||||
| A | ||
| ||
| 68. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Proceed to
Electrical Load Signal or Electric Load Feedback Val
Electric Load Feedback Val
Electrical Load Signal display changes from OFF to ON*1, or Value displayed for Electric Load Feedback Val increases*1
Value displayed for Electric Load Val changes
A
Value displayed for Electric Load Val does not change
B
Electrical Load Signal display does not change from OFF, or Value displayed for Electric Load Feedback Val does not increase
-
- HINT:
- *1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
- The normal value for the ISC compensation amount is engine displacement (liters) x 0.9.
- Even if the results are normal, the electrical load signal system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system.
- *1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
|
|
||||
| A | ||
| ||
| 69. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Result
Suspected Area
Proceed to
Throttle Sensor Position, Calculate Load
Calculate Load decreases while Throttle Sensor Position increases
Mass air flow meter
A
Calculate Load does not decrease while Throttle Sensor Position increases
-
B
|
|
||||
| A | |
| 70. CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
Result Result
Proceed to
Visible foreign matter is not present
A
Visible foreign matter is present
B
Install the mass air flow meter.
|
|
||||
| A | |
| 71. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Condition
Specified Condition
A3-3 (VG) - D97-69 (VG)
Always
Below 1 Ω
A3-2 (E2G) - D97-92 (E2G)
Always
Below 1 Ω
A3-3 (VG) or D97-69 (VG) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 72. PERFORM DRIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Calculate Load.
Read the values displayed on the tester.
- Standard:
Data List
Specified Condition
Calculate Load
90 to 110% of the current value of the vehicle
|
|
||||
| OK | |
| 73. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
Disconnect the ECM connector.
Turn the ignition switch to ON.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
D97-86 (#10) - D97-46 (E01)
Ignition switch ON
11 to 14 V
D97-85 (#20) - D97-46 (E01)
Ignition switch ON
11 to 14 V
D97-84 (#30) - D97-46 (E01)
Ignition switch ON
11 to 14 V
D97-83 (#40) - D97-46 (E01)
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to ECM)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 74. CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
|
||||
| OK | |
| 75. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
- Specified Condition:
Control the Fuel Pump / Speed
Specified Condition
ON
Operating sound heard
OFF
Operating sound not heard
Result Result
Proceed to
Abnormal
A
Normal
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
- If the fuel pump operating noise is abnormal, proceed to step 56.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | |
| 76. INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
|
||||
| A | ||
| ||
| 77. CHECK FUEL SYSTEM |
Check the fuel system.
- Check the fuel pressure.
- Check the fuel pump operation.
- Check the fuel leaks.
- Check the fuel pressure.
- HINT:
- For the fuel system On-vehicle Inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Abnormal |
A |
| Normal |
B |
|
|
||||
| A | |
| 78. CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
Result Result
Proceed to
There is no foreign matter and no signs that fuel pump was stuck
A
There is foreign matter or signs that fuel pump was stuck
B
- HINT:
- If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.
|
|
||||
| A | |
| 79. CHECK FUEL SYSTEM |
Check the fuel system.
- Check the fuel pressure.
- Check the fuel pump operation.
- Check the fuel leaks.
- Check the fuel pressure.
- HINT:
- For the fuel system On-vehicle Inspection, refer to the following procedures (Click here).
|
|
||||
| OK | ||
| ||
| 80. CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
| NEXT | ||
| ||



