Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › CAMSHAFT (w/ EGR Cooler) › 2019.06–2020.05
RM35X0E _51 Engine / Hybrid System _079219 1GD-FTV ENGINE MECHANICAL _0384424 CAMSHAFT(w/ EGR Cooler) A

1GD-FTV ENGINE MECHANICAL  CAMSHAFT(w/ EGR Cooler)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the camshaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)


·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly


Perform initialization -
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/ Exhaust Gas Temperature Sensor for EGR

(Click here)



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative when not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative when not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51406A 3.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)

Hide 52618 4.REMOVE LOWER FRONT BUMPER ABSORBER

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 6.DRAIN ENGINE COOLANT

Hide 85110 7.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 53106B 9.REMOVE RADIATOR COVER SUB-ASSEMBLY

Hide 17751 10.REMOVE NO. 1 AIR CLEANER INLET

Hide 44360 11.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 17030 12.REMOVE AIR HOSE ASSEMBLY

Hide 16470 13.REMOVE RADIATOR RESERVE TANK ASSEMBLY

Hide 16571C 14.REMOVE NO. 1 RADIATOR HOSE

Hide 88359 15.REMOVE VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 16711 16.REMOVE FAN SHROUD

Hide 16572D 17.REMOVE NO. 2 RADIATOR HOSE

Hide 17311B 20.REMOVE NO. 1 AIR INLET DUCT

Hide 88590 21.REMOVE BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)

Hide 53209B 22.REMOVE HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY

Hide 16546 23.REMOVE RADIATOR PROTECTOR (w/o Air Conditioning System)

Hide 53286F 24.REMOVE RADIATOR SIDE AIR SEAL LH (for Wagon)

Hide 53285N 25.REMOVE RADIATOR SIDE AIR SEAL RH (for Wagon)

Hide 51466 26.REMOVE UPPER RADIATOR SUPPORT BRACE LH (for Wagon)

Hide 51465 27.REMOVE UPPER RADIATOR SUPPORT BRACE RH (for Wagon)

Hide 86520 28.REMOVE LOW PITCHED HORN ASSEMBLY

Hide 86510 29.REMOVE HIGH PITCHED HORN ASSEMBLY (for 2-piece Type)

Hide 53205 30.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY

Hide 32921D 31.DISCONNECT OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 32922A 32.DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 16400 33.REMOVE RADIATOR ASSEMBLY

Hide 12601B 34.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Cover)

Hide 25760F 35.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY

Hide 17303T 36.REMOVE AIR PIPE SUB-ASSEMBLY

Hide 26100G 37.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 87209 38.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Heater)

Hide 89421C 40.REMOVE DIESEL TURBO PRESSURE SENSOR

Hide 23941 43.DISCONNECT NO. 1 FUEL FILTER PROTECTOR

Hide 89425D 47.REMOVE NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 16206B 49.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16209 50.DISCONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25601 51.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)

Hide 25601 52.DISCONNECT EGR PIPE WITH COOLER SUB-ASSEMBLY (for Double Actuator EGR Bypass Valve)

Hide 53.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 55.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 57.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 58.REMOVE NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 59.REMOVE INJECTOR ASSEMBLY

Hide 23682 60.REMOVE NOZZLE HOLDER GASKET

Hide 11401Q 61.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 62.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 63.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A345765C01
1.469,1.344 1.052,1.01 1.052,1.01 0.885,1.01 true 1.604,1.375 2.021,1.875 2.021,1.875 2.188,1.875 true 2.208,3.229 2.49,2.833 2.49,2.833 2.656,2.833 true 0.979,3.229 0.729,2.833 0.729,2.833 0.563,2.833 true 1.01,3.323 1,3.75 false 2.219,3.323 2.208,3.75 false 0.677,0.906 0.865,1.063 0.188,0.156 10 true *a 2.656,2.729 2.885,2.896 0.229,0.167 10 false *b 2.198,1.771 2.385,1.927 0.188,0.156 10 true *a 0.354,2.74 0.552,2.906 0.198,0.167 10 false *b 0.938,3.76 1.135,3.927 0.198,0.167 10 true *a 2.146,3.76 2.344,3.927 0.198,0.167 10 true *a
*a Timing Mark
*b Paint Mark


Align the timing mark of the crankshaft pulley and timing chain cover by rotating the crankshaft clockwise.


b.

Make sure that the timing mark of the camshaft timing sprocket is at the top.

HINT:

If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).



c.

Place paint marks on the No. 2 chain sub-assembly.


Hide 64.REMOVE NO. 3 CAMSHAFT BEARING CAP

a.
A345780

Remove the 2 bolts and No. 3 camshaft bearing cap from the cylinder head sub-assembly.


Hide 29300 65.REMOVE VACUUM PUMP ASSEMBLY

Hide 11382C 66.REMOVE CAMSHAFT OIL SEAL RETAINER

Hide 13566B 67.REMOVE TIMING CHAIN GUIDE

a.
A345766

Remove the bolt and timing chain guide from the cylinder head sub-assembly.


Hide 68.REMOVE CAMSHAFT

a.
A345767

Remove the oil pump relief valve plug and gasket from the timing chain cover.


b.
A345768C01
1.792,0.885 2.333,1.083 2.333,1.083 2.5,1.083 true 1.708,1.75 2.333,1.75 true 2.521,0.969 2.719,1.135 0.198,0.167 10 true *a 2.344,1.646 2.563,1.802 0.219,0.156 10 true *b
*a Stopper Plate
*b Pin


Insert a pin into the stopper plate hole of the No. 2 chain tensioner assembly and lock the No. 2 chain tensioner assembly.


c.
A345769C01
1.938,0.625 2.875,0.625 true 0.604,2.938 1.438,2.938 true 2.896,0.521 3.104,0.677 0.208,0.156 10 false *1 0.448,2.833 0.635,2.99 0.188,0.156 10 false *2
*1 No. 1 Camshaft
*2 No. 2 Camshaft


Hold the hexagonal portion of the camshaft with a wrench and loosen the 2 bolts from the No. 1 camshaft and No. 2 camshaft.

NOTICE:

Be careful not to damage the cylinder head sub-assembly with the wrench.



d.
A345770N01
0.583,0.875 0.771,1.042 0.188,0.167 10 true 12 0.021,0.656 0.146,0.823 0.125,0.167 10 true 3 0.031,1.323 0.156,1.49 0.125,0.167 10 true 4 0.073,1.76 0.198,1.927 0.125,0.167 10 true 2 0.052,0.219 0.177,0.385 0.125,0.167 10 true 1 0.479,1.677 0.667,1.844 0.188,0.167 10 true 11 1.198,1.708 1.385,1.875 0.188,0.167 10 true 19 1.917,1.698 2.104,1.865 0.188,0.167 10 true 15 2.625,1.708 2.771,1.875 0.146,0.167 10 true 7 1.292,0.875 1.479,1.042 0.188,0.167 10 true 20 1.979,0.875 2.167,1.042 0.188,0.167 10 true 16 2.667,0.875 2.792,1.042 0.125,0.167 10 true 8 1.052,1.104 1.24,1.271 0.188,0.167 10 true 10 1.74,1.104 1.927,1.271 0.188,0.167 10 true 18 2.417,1.115 2.604,1.281 0.188,0.167 10 true 14 3.208,0.354 3.396,0.521 0.188,0.167 10 true 5 3.125,1.115 3.25,1.281 0.125,0.167 10 true 6 1.198,0.375 1.385,0.542 0.188,0.167 10 true 9 1.854,0.365 2.042,0.531 0.188,0.167 10 true 17 2.542,0.354 2.729,0.521 0.188,0.167 10 true 13

Using several steps, remove the 20 bolts, No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps from the cylinder head sub-assembly.


e.
A345771

Raise the No. 1 camshaft and remove the bolt from the No. 1 camshaft.


f.

Raise the No. 2 camshaft and remove the bolt from the No. 2 camshaft.


g.
A345772

Remove the No. 2 camshaft from the camshaft timing sprocket.


h.
A345774

Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.


i.
A345773

Remove the No. 1 camshaft from the camshaft timing sprocket.


j.
A345775

Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.


k.
A345776

Suspend the No. 2 chain sub-assembly with a string or equivalent.

HINT:

Be careful not to drop the No. 2 chain sub-assembly inside the timing chain cover assembly.