DTC C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
DTC C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1273 C1274 | Detected only during Test Mode. |
|
| C1277 C1278 | Detected only during Test Mode. | Speed sensor rotor |
| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Speed Open | RR speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
| RL Speed Open | RL speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
| Result | Proceed to |
| There are momentary interruptions | A |
| There are no momentary interruptions | B |
| There is a constant open circuit | C |
|
| ||||
|
| ||||
| A | |
| 2.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU and the rear speed sensor (Click here).
Check that there are no momentary interruptions.
| NEXT | |
| 3.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||
| 4.READ VALUE ON TECHSTREAM (REAR SPEED SENSOR) |
Turn the ignition switch off.
Connect Techstream to the DLC3.
Start the engine.
Select the Data List mode on Techstream (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Wheel Speed | RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed | Similar speed as indicated on speedometer |
| RL Wheel Speed | RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed | Similar speed as indicated on speedometer |
Check that there is no difference between the speed value output from the speed sensor displayed on Techstream and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 5.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK REAR SPEED SENSOR INSTALLATION |
![]() |
Turn the ignition switch off.
Check the speed sensor installation (for 2WD).
Check the speed sensor installation (for 4WD).
| Result | Proceed to |
| OK (for 4WD) | A |
| OK (for 2WD) | B |
| NG (for 2WD) | C |
| NG (for 4WD) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 7.CHECK REAR SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the speed sensor tip.
|
| ||||
| OK | |
| 8.CHECK REAR SPEED SENSOR ROTOR |
Remove the rear speed sensor rotor (Click here).
Check the speed sensor rotor.
|
| ||||
| OK | |
| 9.INSPECT REAR SPEED SENSOR |
![]() |
Install the rear speed sensor and the rear speed sensor rotor.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (RR+) - Body ground | Always | 10 kΩ or higher |
| 1 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (RR+) - Body ground | Always | 10 kΩ or higher |
| 2 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 2 (RL+) - Body ground | Always | 10 kΩ or higher |
| 1 (RL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (RL+) - Body ground | Always | 10 kΩ or higher |
| 2 (RL-) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| OK (for 2WD) | A |
| OK (for 4WD) | B |
| NG (for 2WD) | C |
| NG (for 4WD) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 10.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE) |
![]() |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z9 ("A"-2) - z9 ("B"-1) | Always | Below 1 Ω |
| z9 ("A"-2) - z9 ("B"-2) | Always | 10 kΩ or higher |
| z9 ("A"-2) - Body ground | Always | 10 kΩ or higher |
| z9 ("A"-1) - z9 ("B"-2) | Always | Below 1 Ω |
| z9 ("A"-1) - z9 ("B"-1) | Always | 10 kΩ or higher |
| z9 ("A"-1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| z10 ("A"-2) - z10 ("B"-1) | Always | Below 1 Ω |
| z10 ("A"-2) - z10 ("B"-2) | Always | 10 kΩ or higher |
| z10 ("A"-2) - Body ground | Always | 10 kΩ or higher |
| z10 ("A"-1) - z10 ("B"-2) | Always | Below 1 Ω |
| z10 ("A"-1) - z10 ("B"-1) | Always | 10 kΩ or higher |
| z10 ("A"-1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
![]() |
Reconnect the skid control sensor wire (for 2WD).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-17 (RR+) - z9-2 (RR+) | Always | Below 1 Ω |
| A24-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A24-16 (RR-) - z9-1 (RR-) | Always | Below 1 Ω |
| A24-16 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A24-17 (RR+) - N20-1 (RR+) | Always | Below 1 Ω |
| A24-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A24-16 (RR-) - N20-2 (RR-) | Always | Below 1 Ω |
| A24-16 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A24-5 (RL+) - z10-2 (RL+) | Always | Below 1 Ω |
| A24-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| A24-4 (RL-) - z10-1 (RL-) | Always | Below 1 Ω |
| A24-4 (RL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A24-5 (RL+) - O39-1 (RL+) | Always | Below 1 Ω |
| A24-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| A24-4 (RL-) - O39-2 (RL-) | Always | Below 1 Ω |
| A24-4 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.INSPECT SKID CONTROL ECU (SENSOR INPUT) |
![]() |
Reconnect the skid control ECU connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z9-2 (RR+) - Body ground | Ignition switch on (IG) | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| N20-1 (RR+) - Body ground | Ignition switch on (IG) | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| z10-2 (RL+) - Body ground | Ignition switch on (IG) | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| O39-1 (RL+) - Body ground | Ignition switch on (IG) | 8 to 14 V |
|
| ||||
| OK | |
| 13.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
| Result | Proceed to |
| OK | A |
| NG (for 2WD) | B |
| NG (for 4WD) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 14.REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
Replace the rear axle hub and bearing assembly (rear speed sensor rotor) (Click here).
| NEXT | |
| 15.PERFORM TEST MODE (SIGNAL CHECK) |
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||
| 16.REPLACE REAR SPEED SENSOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
| NEXT | |
| 17.PERFORM TEST MODE (SIGNAL CHECK) |
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||
| 18.REPLACE REAR SPEED SENSOR ROTOR |
Turn the ignition switch off.
Remove the rear drive shaft assembly (Click here).
Replace the outboard joint shaft assembly (rear speed sensor rotor) (Click here).
| NEXT | |
| 19.PERFORM TEST MODE (SIGNAL CHECK) |
Install the rear drive shaft assembly.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||