Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for 2GR-FKS) › from 2016.11
RM3160E _53 Suspension _019689 FRONT SUSPENSION _0295251 FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for 2GR-FKS) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for 2GR-FKS)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.REMOVE FRONT WHEELS

Hide 6.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 51441 8.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

Hide 53876A 11.SEPARATE FRONT FENDER LINER LH

Hide 53875A 12.SEPARATE FRONT FENDER LINER RH

Hide 53737B 13.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 14.REMOVE FRONT FENDER APRON SEAL RH

Hide 53299D 15.REMOVE RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 16.REMOVE RADIATOR SIDE SEAL RH

Hide 53295E 17.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 11209 18.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 17750A 19.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17700 21.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 22030 22.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 23.REMOVE THROTTLE BODY GASKET

Hide 82121 25.DISCONNECT ENGINE WIRE

a.
C371522

Remove the 2 bolts and nut, disconnect the engine wire from the automatic transaxle case sub-assembly.


Hide 47220D 26.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for LHD)

Hide 12261 27.DISCONNECT VENTILATION HOSE

Hide 25860 28.DISCONNECT PURGE VALVE (PURGE VSV)

Hide 17126 29.REMOVE NO. 2 SURGE TANK STAY

Hide 17190 30.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Hide 17176 31.REMOVE AIR SURGE TANK TO INTAKE MANIFOLD GASKET

Hide 17403 33.REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

Hide 17584B 34.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

Hide 17410 35.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 36.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 48810 37.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 38.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45220 39.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45460 41.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 42.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 43.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48829A 44.REMOVE FRONT NO. 1 STABILIZER BRACKET LH (for AWD)

a.
C368352

Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front frame assembly.


Hide 48824A 45.REMOVE FRONT NO. 1 STABILIZER BRACKET RH (for AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 46.SEPARATE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY (for AWD)

Hide 32971 48.SEPARATE TRANSMISSION OIL THERMOSTAT

a.
C368351

Remove the 2 bolts and separate the transmission oil thermostat from the front frame assembly.


Hide 12361 49.SEPARATE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

a.

Remove the hole plug.


b.
C365578

Remove the 3 nuts and separate the front engine mounting insulator assembly.


Hide 12372A 50.SEPARATE ENGINE MOUNTING INSULATOR LH

a.

Remove the 2 hole plugs.


b.
C365579

Remove the 3 nuts and separate the engine mounting insulator LH from the front frame assembly.


Hide 12362 51.SEPARATE ENGINE MOUNTING INSULATOR RH

a.

Remove the 2 hole plugs.


b.
C365580

Remove the 3 nuts and separate the engine mounting insulator RH from the front frame assembly.


Hide 12380 52.SEPARATE REAR ENGINE MOUNTING INSULATOR ASSEMBLY

a.

Remove the 2 hole plugs.


b.
C365581

Remove the 2 nuts and separate the rear engine mounting insulator assembly from the front frame assembly.


Hide 51100G 56.REMOVE FRONT FRAME ASSEMBLY

a.
C343621C03
1.198,0.594 1.969,0.594 true 1.021,0.51 1.198,0.667 0.177,0.156 10 true *a
*a Chain Block Assembly
V113147

Turn


Using the chain block assembly, lift the engine with automatic transaxle assembly until the engine is slightly raised off the front frame assembly.

NOTICE:
·

When suspending the engine with automatic transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Lift the engine with automatic transaxle assembly until the engine is slightly raised off the front frame assembly.

·

Do not lift the engine with automatic transaxle assembly excessively.

·

Do not shake the engine with automatic transaxle assembly excessively while it is suspended.




b.
C365582C01
2.063,0.573 2.063,1.198 2.063,1.198 3.146,1.198 true 0.229,1.26 0.323,1.26 0.323,1.26 0.427,0.823 false 1.479,1.188 1.479,0.583 true 0.833,0.656 0.833,1.042 0.833,1.042 1.479,1.042 true 2.75,1.198 2.75,0.625 true 0.073,1.167 0.385,1.323 0.313,0.156 10 false *a 1.427,1.208 1.74,1.365 0.313,0.156 10 false *b 3.188,1.115 3.396,1.313 0.208,0.198 10 false *b
*a Engine Lifter
*b Attachment
V100155

Attachment Placement Location


Support the front frame assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

CAUTION:
C342055

·

The front frame assembly is a very heavy component. Make sure that it is supported securely.

·

If the front frame assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments to keep the front frame assembly level.



c.
C365583C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 6 bolts, 2 nuts and frame side rail plate RH and frame side rail plate LH.


d.

Remove the 6 bolts, 2 nuts and front suspension member rear brace RH and front suspension member rear brace LH.


e.

Slowly lower the front frame assembly.

NOTICE:

When lowering the front frame assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 48829A 57.REMOVE FRONT NO. 1 STABILIZER BRACKET LH (for 2WD)

a.
C291634

Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front frame assembly.


Hide 48824A 58.REMOVE FRONT NO. 1 STABILIZER BRACKET RH (for 2WD)

HINT:

Perform the same procedure as for the LH side.


Hide 59.REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY (for 2WD)

a.

Remove the front stabilizer bar with 2 front No. 2 stabilizer brackets, 2 front No. 1 stabilizer bar bushings and 2 front stabilizer link assemblies from the front frame assembly.


Hide 60.REMOVE STEERING LINK ASSEMBLY (for 2WD)

a.
C366541

Remove the 2 bolts, 2 nuts and steering link assembly from the front frame assembly.

NOTICE:

Keep the nut from rotating while turning the bolt because the nut has its own stopper.



Hide 48069 61.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C292270

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48068 62.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51229B 63.REMOVE NO. 2 FRAME CROSSMEMBER DYNAMIC DAMPER

a.

for 2WD:

i.
C291642

Remove the 2 bolts and No. 2 frame crossmember dynamic damper from the front frame assembly.



b.

for AWD:

i.
C291643

Remove the 2 bolts and No. 2 frame crossmember dynamic damper from the front frame assembly.



Hide 52213A 64.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.


Hide 52216B 65.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.


Hide 52211J 66.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION

a.
C267409C01
2.549,2.876 2.675,2.876 2.675,2.876 2.675,2.165 false 2.289,2.165 2.813,2.165 false 2.828,2.079 3.127,2.239 0.299,0.161 10 SST 1.907,0.875 2.348,0.875 false 2.373,0.795 2.672,0.956 0.299,0.161 10 SST 1.529,1.33 1.331,0.904 1.331,0.904 1.102,0.904 false 0.913,0.819 1.074,0.971 0.161,0.152 10 *1
*1 Front Suspension Member Body Mounting Front Cushion


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265514C04
1.042,2.583 1.042,2.354 false 0.729,2.583 1.031,2.583 false 2.823,0.719 2.823,0.469 false 2.583,2.917 2.885,2.917 false 0.427,2.5 0.885,2.698 0.458,0.198 10 false SST 2.74,0.708 2.948,0.958 0.208,0.25 10 false *a 2.927,2.823 3.125,3.031 0.198,0.208 10 false *b
*a Turn
*b Hold


Using SST, remove each front suspension member body mounting front cushion from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely engaged to the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52217E 67.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C267410C01
2.266,2.213 2.754,2.213 false 2.549,2.898 2.635,2.898 2.635,2.898 2.635,2.213 false 2.783,2.125 3.082,2.291 0.298,0.166 10 SST 1.907,0.872 2.278,0.872 false 2.299,0.787 2.597,0.953 0.298,0.166 10 SST 1.538,1.343 1.357,0.87 1.357,0.87 1.007,0.87 false 0.818,0.782 0.979,0.947 0.162,0.166 10 *1
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265515C04
0.896,2.75 1.031,2.75 1.031,2.75 1.031,2.344 false 2.708,0.781 2.708,0.427 false 2.677,2.917 2.99,2.917 false 0.604,2.677 0.979,2.906 0.375,0.229 10 false SST 2.625,0.781 2.938,1.052 0.313,0.271 10 false *a 3.01,2.854 3.323,3.01 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting rear cushion LH from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely engaged to the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52215 68.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

HINT:

Perform the same procedure as for the LH side.


Hide 69.REMOVE HOLE PLUG

a.

Remove the 10 hole plugs from the front frame assembly.

HINT:

There are 2 different shapes of hole plug.


C294597N01
1.802,0.406 1.958,0.604 0.156,0.198 10 false A 1.979,0.24 2.135,0.438 0.156,0.198 10 false A 3.594,0.063 3.75,0.26 0.156,0.198 10 false A 4.865,0.76 5.021,0.958 0.156,0.198 10 false A 4.063,1.635 4.219,1.833 0.156,0.198 10 false A 3.771,1.885 3.927,2.083 0.156,0.198 10 false A 3.302,1.875 3.458,2.073 0.156,0.198 10 false A 3.125,1.552 3.281,1.75 0.156,0.198 10 false A 1.802,1.958 1.938,2.135 0.135,0.177 10 false B 3.135,2.625 3.281,2.792 0.146,0.167 10 false B