Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) › from 2016.11
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298233 AUTOMATIC TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.REMOVE FRONT WHEELS

Hide 6.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 51441 8.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

Hide 53876A 11.SEPARATE FRONT FENDER LINER LH

Hide 53875A 12.SEPARATE FRONT FENDER LINER RH

Hide 53737B 13.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 14.REMOVE FRONT FENDER APRON SEAL RH

Hide 28100 17.REMOVE STARTER ASSEMBLY

Hide 33820B 18.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 82121 19.DISCONNECT ENGINE WIRE

a.
C366346C01
1.844,2.104 2.271,1.042 2.271,1.042 2.49,1.042 true 0.427,2.99 0.635,2.99 true 1,1.375 1.24,1.594 0.24,0.219 10 true *b 1.979,2.458 2.219,2.677 0.24,0.219 10 true *a 2.583,0.958 2.896,1.156 0.313,0.198 10 false *1 0.167,2.896 0.396,3.094 0.229,0.198 10 true *2
*a Transmission Wire Connector
*b Park/Neutral Position Switch Assembly Connector
*1 Engine Wire
*2 Earth Wire


Disconnect the park/neutral position switch assembly connector.


b.

Disengage the claw, rotate the lever and disconnect the connector of the transmission wire connector.


c.

Remove the 2 bolts and nut, and disconnect the engine wire from the automatic transaxle case sub-assembly.


d.

Remove the bolt to separate the earth wire.


e.

Disengage the clamp to separate the engine wire.


Hide 35104V 20.SEPARATE BREATHER PLUG HOSE

a.
C366359

Disengage the 3 hose clamps to separate the breather plug hose.


Hide 16281K 21.DISCONNECT NO. 4 WATER BY-PASS HOSE

Hide 16267H 22.DISCONNECT NO. 3 WATER BY-PASS HOSE

Hide 16570 23.REMOVE RADIATOR PIPE ASSEMBLY

a.
C370125C01
1.813,0.771 2.115,0.427 2.115,0.427 2.406,0.427 false 2.438,0.313 2.75,0.51 0.313,0.198 10 false *1
*1 Radiator Pipe Assembly


Remove the bolt and radiator pipe assembly from the automatic transaxle assembly.


Hide 32942 24.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 32941 25.DISCONNECT NO. 1 TRANSMISSION OIL COOLER HOSE

Hide 22030 26.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 12261 27.DISCONNECT VENTILATION HOSE

Hide 25860 28.DISCONNECT PURGE VALVE (PURGE VSV)

Hide 17126 29.REMOVE NO. 2 SURGE TANK STAY

Hide 17190 30.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Hide 17176 31.REMOVE AIR SURGE TANK TO INTAKE MANIFOLD GASKET

Hide 32.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C360015

Disconnect the air fuel ratio sensor (for Bank 1) connector.


b.
C360016C01
0.5,0.438 0.719,0.635 0.219,0.198 10 true *a 2.167,1.906 2.385,2.104 0.219,0.198 10 true *b 2.563,1.521 2.781,1.719 0.219,0.198 10 true *b 2.885,1.146 3.104,1.344 0.219,0.198 10 true *b
*a Hose Clamp
*b Wire Harness Clamp


Disengage the hose clamp and 3 wire harness clamps.


c.

Remove the bolt and wire harness clamp bracket from the cylinder head RH.


Hide 17403 33.REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

Hide 17584B 34.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

Hide 17410 35.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 17141 37.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 17173 38.REMOVE EXHAUST MANIFOLD TO HEAD GASKET (for Bank 1)

Hide 48810 39.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 40.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 45220 43.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45470 44.SEPARATE TIE ROD ASSEMBLY LH

Hide 45460 45.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 48069 46.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 47.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 48.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Hide 43420G 50.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side)

Hide 57.INSTALL ENGINE HANGER

a.
C363219E01
1.917,1.375 2.417,1.083 true 1.333,0.917 1.49,1.115 0.156,0.198 10 true A 1.281,1.833 1.438,2.031 0.156,0.198 10 true B 2.51,0.979 2.917,1.146 0.406,0.167 10 false SST

Install SST (engine hanger attachment) to the cylinder head RH with the 2 bolts.

SST
09940-30010  (91671-10825)

Torque:
Bolt (A) : 33 N*m (337 kgf*cm, 24 ft.*lbf)
Bolt (B) : 10 N*m (102 kgf*cm, 7 ft.*lbf)

Item Part No.
Bolt (A) 91671-10825
Bolt (B) 91551-80620

NOTICE:

Do not use any bolts other than the specified bolts.



b.
C363220C01
2.208,0.823 2.51,0.49 false 1.667,1.917 1.979,1.604 true 2.594,0.354 2.906,0.552 0.313,0.198 10 false *1 1.469,1.958 1.813,2.135 0.344,0.177 10 true SST
*1 No. 1 Engine Hanger


Install SST (collar) and No. 1 engine hanger to SST (engine hanger attachment) with the bolt.

SST
09940-30010  (09941-03010)

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

Item Part No.
No. 1 Engine Hanger 12281-36020
Bolt 91552-81050

NOTICE:

Do not use any bolts other than the specified bolt.



c.
C363244C01
1.354,1.042 1.75,1.083 false 1.833,1.01 2.115,1.24 0.281,0.229 10 true *1
*1 No. 2 Engine Hanger


Install the No. 2 engine hanger to the cylinder head LH with the 2 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

Item Part No.
No. 2 Engine Hanger 12282-31100
Bolt 91671-10825

NOTICE:

Do not use any bolts other than the specified bolts.



Hide 58.INSTALL ENGINE SUPPORT BRIDGE

a.

Install SST to the vehicle body as shown in the illustration.

C360017C01
5.917,5.667 6.333,5.667 true 0.917,5.75 2.25,5.75 true 5.688,6.281 6.156,6.542 6.156,6.542 6.344,6.542 true 1.344,6.198 1.927,6.375 1.927,6.375 2.24,6.375 true 2.146,2.573 2.323,2.396 2.323,2.396 2.49,2.396 true 4.542,2.865 4.26,2.583 4.26,2.583 3.917,2.583 true 4.156,3.875 4.792,4.219 4.792,4.219 5.479,4.219 true 6.396,5.563 6.708,5.76 0.313,0.198 10 false *a 2.333,5.646 2.646,5.844 0.313,0.198 10 false *a 2.292,6.26 2.604,6.458 0.313,0.198 10 false *b 6.396,6.427 6.708,6.625 0.313,0.198 10 false *b 2.542,2.26 2.792,2.458 0.25,0.198 10 true *c 3.656,2.458 3.906,2.656 0.25,0.198 10 true *c 5.583,4.125 6.042,4.323 0.458,0.198 10 false SST 6.646,0.646 6.896,0.844 0.25,0.198 10 true *e 6.25,1.563 6.5,1.76 0.25,0.198 10 true *d 0.448,0.5 0.698,0.688 0.25,0.188 10 true *e 1.135,1.542 1.448,1.74 0.313,0.198 10 true *d
*a Support Shaft *b Front Side Member
*c Cloth *d Front Side
*e Front Suspension Nut - -


SST
09940-10020  

CAUTION:
·
C330755C01
0.448,1.167 0.781,1.167 false 2.438,1.167 2.771,1.167 false 1.052,1.781 1.052,1.448 1.052,1.448 1.219,1.448 false 2.604,1.781 2.604,1.448 2.604,1.448 2.438,1.448 false 0.292,1.094 0.604,1.25 0.313,0.156 10 false *a 2.271,1.094 2.583,1.25 0.313,0.156 10 false *a 1.281,1.385 1.594,1.542 0.313,0.156 10 false *b 2.271,1.385 2.583,1.542 0.313,0.156 10 false *b
*a Support Shaft
*b Front Side Member


Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.

·

The engine support bridge may fall off if there is any oil or grease on the front side member or it is installed on an unlevel surface.



NOTICE:
·

Prevent SST from contacting the vehicle body exterior and windshield glass.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed before performing work.




b.
C338947C01
0.615,1.479 0.615,0.656 0.615,0.656 0.5,0.656 false 1.042,2.125 1.667,2.125 false 1.031,2.469 2.167,2.469 false 0.875,2.771 0.875,2.458 0.875,2.458 0.76,2.458 false 1.708,2.01 2.063,2.281 0.354,0.271 10 false *a 0.292,0.552 0.604,0.823 0.313,0.271 10 false *b 0.552,2.354 0.917,2.583 0.365,0.229 10 false *c 2.208,2.375 2.563,2.667 0.354,0.292 10 false *d
*a Support Shaft
*b Sub Beam
*c Front Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.


c.

Install the chain block to the sling bracket.

C360020C01
1.646,2.021 1.833,2.021 1.833,2.021 1.979,2.146 true 1.625,1.052 1.802,0.823 1.802,0.823 1.979,0.823 true 1.646,2.25 1.979,2.25 true 2.24,1.219 2.583,1.219 true 2.625,1.135 2.865,1.344 0.24,0.208 10 true *a 1.469,1.063 1.708,1.271 0.24,0.208 10 true *b 1.427,2.156 1.625,2.354 0.198,0.198 10 true *d 1.427,1.906 1.604,2.115 0.177,0.208 10 true *c
*a Chain Block *b Sling Bracket
*c Fuse Shackle *d Shackle (A)



d.

Install the division bar to the chain block with the fuse shackle and shackle (A).

CAUTION:
·
C338949C01
0.458,2.313 0.583,2.313 0.583,2.313 0.875,2.635 false 0.354,2.677 0.479,2.677 0.479,2.677 0.865,2.865 false 2.177,2.271 2.302,2.271 2.302,2.271 2.604,2.594 false 2.073,2.656 2.198,2.656 2.198,2.656 2.583,2.844 false 0.281,2.208 0.604,2.469 0.323,0.26 10 false *a 0.167,2.573 0.51,2.844 0.344,0.271 10 false *b 1.99,2.156 2.313,2.417 0.323,0.26 10 false *a 1.885,2.542 2.229,2.813 0.344,0.271 10 false *b
*a Fuse Shackle
*b Shackle (A)


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·

If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with automatic transaxle assembly may fall.

·
C330757C01
2.75,1 3.083,1 false 1.01,1 1.344,1 false 0.917,1.417 1.333,1.583 true 2.635,1.396 3.083,1.583 true 1.396,0.917 1.708,1.073 0.313,0.156 10 false *a 1.385,1.51 1.698,1.667 0.313,0.156 10 false *b 3.125,0.917 3.354,1.083 0.229,0.167 10 false *a 3.135,1.5 3.354,1.667 0.219,0.167 10 false *b
*a Fuse Shackle
*b Fuse Bolt


Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.

·

If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.




e.

Connect the division bar to the No. 1 engine hanger with the shackle (A).

C360018C01
1.948,1.75 2.042,1.583 2.042,1.583 2.208,1.583 true 1.76,4.896 1.917,5.125 1.917,5.125 2.135,5.125 true 0.865,3.969 0.865,3.573 true 0.698,2.021 0.698,1.563 false 1.729,4.313 2.01,4.313 2.01,4.313 2.01,4.563 true 1.615,1.24 1.927,1.24 true 1.729,4.552 2.323,4.552 true 2,1.146 2.26,1.354 0.26,0.208 10 true *b 2.188,5.031 2.448,5.25 0.26,0.219 10 true *2 0.76,3.99 1.021,4.208 0.26,0.219 10 true *a 0.635,2.063 0.885,2.271 0.25,0.208 10 true *a 2.375,4.469 2.635,4.688 0.26,0.219 10 true *b 2.271,1.479 2.521,1.688 0.25,0.208 10 true *1
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)



f.

Connect the division bar to the No. 2 engine hanger with the 2 shackles (A).


g.

Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.

C368320C01
2.25,1.188 2.49,1.188 false 1.51,2 1.99,2 true 1.542,1.5 1.771,1.708 0.229,0.208 10 true *c 1.292,1.896 1.51,2.125 0.219,0.229 10 true *b 2.542,1.094 2.771,1.302 0.229,0.208 10 true *a
*a Chain Block Assembly *b Suspension Ring
*c 120 mm or more - -



h.

Adjust the position of the chain block assembly so that the chain is perpendicular to the main beam and sub beams as shown in the illustration.

C366334C01
4.323,0.76 4.438,0.448 4.438,0.448 4.583,0.448 false 0.958,1.865 1.823,1.865 true 3.969,1.135 4.104,1.135 false 5.333,1.865 6.198,1.865 true 3.813,0.354 4.125,0.552 0.313,0.198 10 false *h 4.646,0.344 4.958,0.542 0.313,0.198 10 false *b 6.25,1.75 6.563,1.948 0.313,0.198 10 false *c 1.719,0.354 2.031,0.552 0.313,0.198 10 false *d 5.51,1.313 5.688,1.51 0.177,0.198 10 true *i 1.563,1.281 1.74,1.479 0.177,0.198 10 true *i 0.771,1.74 1.083,1.938 0.313,0.198 10 false *c 5.302,0.344 5.615,0.542 0.313,0.198 10 false *e 4.156,1.021 4.469,1.219 0.313,0.198 10 true *a 4.375,3.781 4.688,3.979 0.313,0.198 10 false *g 1.083,3.75 1.396,3.948 0.313,0.198 10 false *f
*a Chain Block Assembly *b Main Beam
*c Sub Beam *d Dimension (A)
*e Dimension (B) *f Correct
*g Incorrect *h Right to Left Adjustment
*i Front to Rear Adjustment - -


CAUTION:
C342687C02
1.417,1.563 1.594,1.167 1.594,1.167 1.958,1.167 false 2.063,1.042 2.375,1.24 0.313,0.198 10 false *a 0.323,1.083 0.635,1.281 0.313,0.198 10 false *b 2.823,1.031 3.135,1.229 0.313,0.198 10 false *c
*a Main Beam
*b Dimension (A)
*c Dimension (B)


·

To prevent the engine assembly with automatic transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.

·

Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.

·

Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with automatic transaxle assembly and engine support bridge to fall, possibly causing serious injury.




i.

Tighten the 6 wing bolts and 2 bolts.

C366335

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

CAUTION:
C330761

·

Do not perform any procedures before tightening the bolts to the specified torque.

·

Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.




j.
C339730C01
2.604,3.26 2.917,3.458 0.313,0.198 10 true *a
*a Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C330770C01
2.99,2.292 3.302,2.448 0.313,0.156 10 false *a
*a 41 N*m (418 kgf*cm, 30 ft.*lbf) or more


·

When suspending the engine assembly with automatic transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.




Hide 11361J 59.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A396416

Remove the 2 bolts and flywheel housing under cover from the automatic transaxle case sub-assembly.


Hide 32101A 60.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
A389112

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 61.INSTALL BELT

a.
C363985C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and nut and disconnect the windshield washer jar assembly from the vehicle body.


b.

Install SST to the vehicle body as shown in the illustration.

C366337N01
4.135,3.75 6.229,3.76 true 0.906,3.75 3,3.76 true 0.563,3.677 1.021,3.875 0.458,0.198 10 false SST 6.302,3.677 6.76,3.875 0.458,0.198 10 false SST

SST
09727-00110  


c.

Using the ratchet buckle, tighten the 2 belts until there is no slack.

C366338C01
4.333,0.802 4.604,1.323 4.604,1.323 5.646,1.323 true 1.573,1.24 2.729,1.24 2.729,1.24 2.865,0.854 true 1.229,1.823 3.479,1.833 true 3.625,1.833 5.875,1.844 true 5.74,1.219 6.052,1.417 0.313,0.198 10 true *a 1.375,1.125 1.635,1.354 0.26,0.229 10 false *a 5.979,1.75 6.438,1.948 0.458,0.198 10 false SST 0.875,1.729 1.333,1.927 0.458,0.198 10 false SST
*a Ratchet Buckle - -



Hide 12362 63.REMOVE ENGINE MOUNTING INSULATOR RH

a.
C366340

Remove the nut and engine mounting insulator RH from the engine mounting bracket RH.


Hide 64.INSTALL ENGINE SUPPORT BAR

a.

Install SST (support bar) to the engine mounting bracket RH with the stud bolt and nut as shown in the illustration.

C366339C01
1.979,0.438 1.792,0.438 1.792,0.438 1.667,0.26 true 1.292,0.531 1.542,0.531 true 1.333,1.031 1.583,1.031 true 5.229,0.802 5.479,0.802 true 5.219,1.094 5.469,1.094 true 6.375,2.01 6.375,1.802 6.375,1.802 6.563,1.458 true 6.635,2.073 6.635,2.49 true 4.094,4.875 4.094,5.708 false 3.781,5.115 3.781,5.708 3.781,5.708 4.5,5.708 false 1.292,6.708 1.594,6.708 1.594,6.708 1.781,6.948 true 1.563,7.313 1.813,7.313 true 0.667,4.042 2.781,4.042 true 5.01,0.698 5.198,0.896 0.188,0.198 10 true *d 1.073,0.427 1.271,0.615 0.198,0.188 10 true *1 1.167,0.927 1.313,1.115 0.146,0.188 10 true *i 5,0.979 5.188,1.177 0.188,0.198 10 true *e 6.302,2.052 6.49,2.25 0.188,0.198 10 true *h 6.563,2.521 6.75,2.719 0.188,0.198 10 true *g 4.552,5.604 4.74,5.802 0.188,0.198 10 true *a 1.083,6.615 1.271,6.813 0.188,0.198 10 true *h 1.354,7.219 1.542,7.417 0.188,0.198 10 true *f 0.479,3.938 0.667,4.135 0.188,0.198 10 true *b 2.042,0.323 2.229,0.521 0.188,0.198 10 true *c

Text in Illustration
*1 Engine Mounting Bracket RH - -
*a SST (Belt) *b SST (Support Bar)
*c SST (Nut) *d SST (Spacer 20)
*e SST (Spacer 30) *f SST (Bolt 40)
*g SST (Bolt 90) *h SST (Washer)
*i Stud Bolt - -

SST
09940-20011  (09941-02010, 09941-02020, 09941-02030, 09941-02040, 09941-02050, 09941-02060, 09941-02070)

CAUTION:

To prevent the engine with automatic transaxle assembly from falling while servicing, do not remove SST (belt).


HINT:

Tighten the nut by hand.



b.

Install SST (support bar) to the vehicle body with the 2 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 12360 65.REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

a.
C366341

Remove the bolt and front engine mounting insulator assembly from the front engine mounting bracket.


Hide 12372A 66.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C366342

Remove the nut and engine mounting insulator LH from the automatic transaxle assembly.


Hide 67.SUPPORT ENGINE ASSEMBLY

a.
C366343

Set an engine lifter.

CAUTION:

To prevent the engine assembly with automatic transaxle assembly from falling while servicing, do not remove SST.


NOTICE:

Make sure that there is clearance between the engine oil pan assembly and engine lifter.



Hide 68.REMOVE BELT

a.

Remove SST from the vehicle body.

C366361C02
4.031,2.677 5.875,2.677 true 1.25,2.698 3.073,2.698 true 5.958,2.583 6.417,2.781 0.458,0.198 10 false SST 0.958,2.615 1.417,2.813 0.458,0.198 10 false SST


Hide 30500 69.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.

Support the automatic transaxle assembly with a transmission jack.

NOTICE:

Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachments.



b.
C361050

Remove the 11 bolts and automatic transaxle assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.



Hide 70.DISCONNECT INLET NO. 2 OIL COOLER HOSE

Hide 71.DISCONNECT OUTLET NO. 3 OIL COOLER HOSE

Hide 32907C 72.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

Hide 33493A 73.REMOVE TRANSMISSION OIL COOLER

Hide 12311A 74.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C366345

Remove the 4 bolts and front engine mounting bracket from the automatic transaxle assembly.


Hide 12325A 75.REMOVE ENGINE MOUNTING BRACKET LH

a.
C361052

Remove the 3 bolts and engine mounting bracket LH from the automatic transaxle case sub-assembly.


Hide 76.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C361053

Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle case sub-assembly.


Hide 77.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C368322

Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.


Hide 35150 78.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C368937

Remove the transmission case plug assembly from the automatic transaxle assembly.


Hide 35104V 79.REMOVE BREATHER PLUG HOSE

C364010

a.

Using a screwdriver, remove the breather plug hose from the No. 1 breather plug (ATM).

NOTICE:

Be careful not to damage the No. 1 breather plug (ATM).



b.
C364011C01
1.688,0.438 2.24,0.438 false 1.167,1.396 1.719,1.396 false 1.531,0.375 1.844,0.531 0.313,0.156 10 false *1 1,1.323 1.313,1.479 0.313,0.156 10 false *2
*1 Breather Plug Sub-assembly
*2 Breather Plug Hose


Remove the breather plug sub-assembly from the breather plug hose.

NOTICE:

Be careful not to damage the breather plug sub-assembly.



Hide 32000 80.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the automatic transaxle assembly.


Hide 32101 82.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY