32000
1.INSTALL TORQUE CONVERTER ASSEMBLY
| *a | Matchmark |
| *b | Key |
Turn the front oil pump drive gear so that either key is at the top and place a matchmark on the transaxle housing to indicate the position of the key.
| *a | Groove |
| *b | Matchmark |
|
MP Grease |
Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.
| *1 | Front Oil Pump Oil Seal |
| *a | Matchmark |
Align the matchmark on the torque converter assembly with the one on the transaxle housing and engage the splines of the input shaft with the turbine runner splines.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the front oil pump oil seal.
| *1 | Front Oil Pump Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.
Do not push the torque converter assembly excessively when rotating it.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the front oil pump oil seal.
| *1 | Front Oil Pump Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the keys of the front oil pump drive gear into the grooves of the torque converter assembly.
Do not push the torque converter assembly excessively when rotating it.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the front oil pump oil seal.
Clean the drive plate and torque converter assembly setting bolt holes.
| *a | Engine Assembly Surface |
| *b | Drive Plate and Ring Gear Sub-assembly Surface |
Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surface of the drive plate and ring gear sub-assembly*b.
Make sure to deduct the thickness of the straightedge.
Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.
Dimension (A) + 1 mm (0.0394 in.) or more
Make sure to deduct the thickness of the straightedge.
If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
Do not include the thickness of the set block.
35104V
2.INSTALL BREATHER PLUG HOSE
Install the breather plug sub-assembly to the breather plug hose.
Install the breather plug hose to the No. 1 breather plug (ATM).
35150
3.INSTALL TRANSMISSION CASE PLUG ASSEMBLY
Coat the O-ring of a new transmission case plug assembly with Toyota Genuine ATF WS.
Install the transmission case plug assembly to the automatic transaxle assembly.
4.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.
5.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Install the No. 1 transmission control cable bracket to the automatic transaxle case sub-assembly with the 2 bolts.
12311A
6.INSTALL FRONT ENGINE MOUNTING BRACKET
Install the front engine engine mounting bracket to the automatic transaxle assembly with the 4 bolts.
12325A
7.INSTALL ENGINE MOUNTING BRACKET LH
Install the engine mounting bracket LH to the automatic transaxle case sub-assembly with the 3 bolts.
32907C
8.INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE
33493A
9.INSTALL TRANSMISSION OIL COOLER
10.CONNECT OUTLET NO. 3 OIL COOLER HOSE
11.CONNECT INLET NO. 2 OIL COOLER HOSE
12.SUPPORT ENGINE ASSEMBLY
Set an engine lifter.
Make sure that there is clearance between the engine oil pan assembly and engine lifter.
30500
13.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
| *1 | Crankshaft |
| *2 | Torque Converter Assembly Centerpiece |
|
Clutch Spline Grease |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz)
| *1 | Knock Pin |
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the automatic transaxle assembly with the 11 bolts shown in the illustration.
| Bolt | Length |
|---|---|
| (A) | 55 mm (2.17 in.) |
| (B) | 41 mm (1.61 in.) |
| (C) | 33 mm (1.30 in.) |
Confirm that the knock pins are installed to the automatic transaxle assembly contact surface of the cylinder block sub-assembly before installing the automatic transaxle assembly.
Do not forcibly pry on the automatic transaxle assembly.
Check that the torque converter assembly rotates.
14.INSTALL BELT
Install SST to the vehicle body as shown in the illustration.
Using the ratchet buckle, tighten the 2 belts until there is no slack.
| *a | Ratchet Buckle | - | - |
12372A
15.INSTALL ENGINE MOUNTING INSULATOR LH
Install the engine mounting insulator LH to the automatic transaxle assembly with the nut.
12360
16.INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY
Install the front engine mounting insulator assembly to the front engine mounting bracket with the bolt.
17.REMOVE ENGINE SUPPORT BAR
Remove the 2 bolts and SST (support bar) from the vehicle body.
Remove the nut, stud bolt and SST (support bar) from the engine mounting bracket RH.
12362
18.INSTALL ENGINE MOUNTING INSULATOR RH
Install the engine mounting insulator RH to the engine mounting bracket RH with the nut.
51100G
19.INSTALL FRONT FRAME ASSEMBLY
20.REMOVE BELT
Remove SST from the vehicle body.
Connect the windshield washer jar assembly to the vehicle body with the bolt and nut.
32101A
21.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Remove any remaining adhesive from the 6 drive plate and torque converter assembly setting bolts.
| *a | Adhesive |
Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.
Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.
First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.
11361J
22.INSTALL FLYWHEEL HOUSING UNDER COVER
Install the flywheel housing under cover to the automatic transaxle case sub-assembly with the 2 bolts.
23.REMOVE ENGINE SUPPORT BRIDGE
Remove SST from the vehicle body.
Prevent SST from contacting the vehicle body or windshield glass.
24.REMOVE ENGINE HANGER
Remove the 2 bolts and No. 2 engine hanger from the cylinder head LH.
Remove the bolt, SST (collar) and No. 1 engine hanger from engine hanger attachment.
Remove the 2 bolts and SST (engine hanger attachment) from cylinder head RH.
12361
25.CONNECT FRONT ENGINE MOUNTING INSULATOR ASSEMBLY
12372A
26.CONNECT ENGINE MOUNTING INSULATOR LH
12362
27.CONNECT ENGINE MOUNTING INSULATOR RH
12380
28.CONNECT REAR ENGINE MOUNTING INSULATOR ASSEMBLY
32971
29.CONNECT TRANSMISSION OIL THERMOSTAT
43420G
30.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side)
43420
31.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
43410
32.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
48069
33.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
34.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
45470
35.CONNECT TIE ROD ASSEMBLY LH
45460
36.CONNECT TIE ROD ASSEMBLY RH
Use the same procedure as for the LH side.
89543
37.INSTALL FRONT SPEED SENSOR
45220
38.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
43502H
39.INSTALL FRONT AXLE SHAFT NUT
48810
40.INSTALL FRONT STABILIZER LINK ASSEMBLY LH
48820B
41.INSTALL FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure as for the LH side.
17173
42.INSTALL EXHAUST MANIFOLD TO HEAD GASKET (for Bank 1)
17141
43.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)
17410
44.INSTALL FRONT EXHAUST PIPE ASSEMBLY
17584B
45.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)
17403
46.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY
47.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket to the cylinder head RH with the bolt.
Engage the hose clamp and 3 wire harness clamps.
Connect the air fuel ratio sensor (for Bank 1) connector.
35104V
48.INSTALL BREATHER PLUG HOSE
Engage the 3 hose clamps to install the breather plug hose.
82121
49.CONNECT ENGINE WIRE
| *a | Transmission Wire Connector |
| *b | Park/Neutral Position Switch Assembly Connector |
| *1 | Engine Wire |
| *2 | Earth Wire |
|
Bolt |
|
Nut |
Engage the clamp to connect the engine wire.
Connect the earth wire with the bolt.
Connect the engine wire to the automatic transaxle case sub-assembly with the 2 bolts and nut.
Connect the park/neutral position switch connector.
Connect the connector of the transmission wire connector and rotate the lever to engage the claw.
Rotate the lever until the claw of the transmission wire connector makes a click sound.
17176
50.INSTALL AIR SURGE TANK TO INTAKE MANIFOLD GASKET
17190
51.INSTALL INTAKE AIR SURGE TANK ASSEMBLY
25860
52.CONNECT PURGE VALVE (PURGE VSV)
22030
53.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
12261
54.CONNECT VENTILATION HOSE
32943
55.CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE
32942
56.CONNECT OUTLET NO. 1 OIL COOLER HOSE
16570
57.INSTALL RADIATOR PIPE ASSEMBLY
Install the radiator pipe assembly to the automatic transaxle assembly with the bolt.
16267H
58.CONNECT NO. 3 WATER BY-PASS HOSE
16281K
59.CONNECT NO. 4 WATER BY-PASS HOSE
33820B
60.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
28100
61.INSTALL STARTER ASSEMBLY
55701J
62.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
63.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
64.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65.ADD ENGINE COOLANT
66.ADD AUTOMATIC TRANSAXLE FLUID
67.INSPECT FOR COOLANT LEAK
68. WARM UP ENGINE
69.INSPECT FOR EXHAUST GAS LEAK
53737B
70.INSTALL FRONT FENDER APRON SEAL LH
53736
71.INSTALL FRONT FENDER APRON SEAL RH
53876A
72.INSTALL FRONT FENDER LINER LH
53875A
73.INSTALL FRONT FENDER LINER RH
58166
74.INSTALL FRONT FLOOR COVER LH
51442
75.INSTALL NO. 2 ENGINE UNDER COVER
51441
76.INSTALL NO. 1 ENGINE UNDER COVER
77.INSTALL FRONT WHEELS
78.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
79.CHECK FOR SPEED SENSOR SIGNAL
80.CHECK AUTOMATIC TRANSAXLE SYSTEM
If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION