Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) › from 2018.09
RM3160E _52 Drivetrain _060165 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0303764 AUTOMATIC TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C361056C01
0.604,1.781 0.917,1.438 true 0.635,0.427 0.875,0.885 true 2.115,0.208 2.813,0.188 true 0.448,0.281 0.76,0.479 0.313,0.198 10 true *b 0.417,1.688 0.729,1.885 0.313,0.198 10 true *b 2.885,0.052 3.198,0.25 0.313,0.198 10 true *a
*a Matchmark
*b Key


Turn the front oil pump drive gear so that either key is at the top and place a matchmark on the transaxle housing to indicate the position of the key.


b.
C361055C01
1.167,0.292 1.604,0.615 false 1.729,1.583 2.167,1.906 false 0.979,0.125 1.292,0.323 0.313,0.198 10 false *a 2.229,1.885 2.542,2.083 0.313,0.198 10 false *b
*a Groove
*b Matchmark
V100135C01
0,0 0,0 false

MP Grease


Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C363765C01
0.573,0.271 1.271,0.74 true 0.583,0.281 1.25,0.573 false 2.333,0.917 2.906,0.708 true 2.344,1.198 2.906,0.708 true 0.406,0.146 0.719,0.344 0.313,0.198 10 false *a 2.948,0.573 3.26,0.771 0.313,0.198 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Align the matchmark on the torque converter assembly with the one on the transaxle housing and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C363766C01
0.74,0.281 1.344,0.448 true 0.76,2.01 1.344,1.594 true 2.323,0.854 2.917,0.677 true 2.333,1.167 2.906,0.677 true 0.552,0.135 0.802,0.344 0.25,0.208 10 false *a 0.583,1.906 0.833,2.115 0.25,0.208 10 false *a 2.938,0.531 3.188,0.74 0.25,0.208 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C363767C01
0.604,0.271 1.26,0.615 true 0.646,0.292 1.26,0.458 true 2.281,0.833 2.896,0.677 true 2.302,1.167 2.885,0.677 true 0.417,0.125 0.729,0.323 0.313,0.198 10 false *a 2.927,0.531 3.24,0.729 0.313,0.198 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the keys of the front oil pump drive gear into the grooves of the torque converter assembly.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C347941C01
2.375,0.969 2.375,0.729 2.375,0.729 2.531,0.729 false 2.438,1.729 2.438,1.479 2.438,1.479 2.688,1.479 false 0.75,0.333 1,0.333 1,0.333 1.25,0.969 true 0.969,2.979 0.969,2.396 true 2.302,0.979 2.615,1.135 0.313,0.156 10 false *a 2.385,1.75 2.698,1.906 0.313,0.156 10 false *b 2.177,0.292 2.333,0.49 0.156,0.198 10 false A 0.583,0.229 0.896,0.385 0.313,0.156 10 false *a 0.917,3 1.229,3.156 0.313,0.156 10 false *b
*a Engine Assembly Surface
*b Drive Plate and Ring Gear Sub-assembly Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surface of the drive plate and ring gear sub-assembly*b.

NOTICE:

Make sure to deduct the thickness of the straightedge.



h.
C363763C01
2.417,0.448 2.573,0.646 0.156,0.198 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

Dimension (A) + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 35104V 2.INSTALL BREATHER PLUG HOSE

a.

Install the breather plug sub-assembly to the breather plug hose.


b.

Install the breather plug hose to the No. 1 breather plug (ATM).


Hide 35150 3.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Coat the O-ring of a new transmission case plug assembly with Toyota Genuine ATF WS.


b.

Install the transmission case plug assembly to the automatic transaxle assembly.


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 5.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle case sub-assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12311A 6.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine engine mounting bracket to the automatic transaxle assembly with the 4 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12325A 7.INSTALL ENGINE MOUNTING BRACKET LH

a.

Install the engine mounting bracket LH to the automatic transaxle case sub-assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 32907C 8.INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

Hide 33493A 9.INSTALL TRANSMISSION OIL COOLER

Hide 10.CONNECT OUTLET NO. 3 OIL COOLER HOSE

Hide 36100 12.INSTALL TRANSFER ASSEMBLY

Hide 13.SUPPORT ENGINE ASSEMBLY

a.
C366344

Set an engine lifter.

NOTICE:

Make sure that there is clearance between the engine oil pan assembly and engine lifter.



Hide 30500 14.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C363764C01
1.698,1.063 1.927,1.063 false 1.167,1 1.479,1.198 0.313,0.198 10 false *1 1.969,0.979 2.281,1.177 0.313,0.198 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



b.
C290460C01
2.094,0.552 2.656,0.552 true 0.469,1.313 1.031,1.313 true 0.292,1.208 0.604,1.406 0.313,0.198 10 false *1 2.698,0.427 3.01,0.625 0.313,0.198 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C363759N01
1.229,0.208 1.542,0.406 0.313,0.198 10 false A 1.792,0.042 2.104,0.24 0.313,0.198 10 false A 2.656,0.167 2.969,0.365 0.313,0.198 10 false A 2.813,0.646 3.125,0.844 0.313,0.198 10 false A 2.813,0.667 3.125,0.865 0.313,0.198 10 false A 2.896,1.094 3.208,1.292 0.313,0.198 10 false A 2.802,1.521 3.115,1.719 0.313,0.198 10 false A 2.573,1.781 2.927,1.99 0.354,0.208 10 false C 2.01,1.917 2.365,2.125 0.354,0.208 10 false C 1.49,1.917 1.844,2.125 0.354,0.208 10 false C 1.01,1.708 1.177,1.906 0.167,0.198 10 true B 0.823,0.75 0.99,0.948 0.167,0.198 10 true A

While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the automatic transaxle assembly with the 11 bolts shown in the illustration.

Torque:
Bolt (A) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (B) : 46 N*m (469 kgf*cm, 34 ft.*lbf)
Bolt (C) : 43 N*m (438 kgf*cm, 32 ft.*lbf)

Bolt Length:
Bolt Length
(A) 55 mm (2.17 in.)
(B) 41 mm (1.61 in.)
(C) 33 mm (1.30 in.)


NOTICE:
·

Confirm that the knock pins are installed to the automatic transaxle assembly contact surface of the cylinder block sub-assembly before installing the automatic transaxle assembly.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter assembly rotates.




Hide 15.INSTALL BELT

a.

Install SST to the vehicle body as shown in the illustration.

C366362C02
3.813,5.031 6.302,5.031 true 1.156,5.042 3.302,5.042 true 6.438,4.969 6.896,5.167 0.458,0.198 10 false SST 0.813,4.979 1.271,5.177 0.458,0.198 10 false SST

SST
09727-00110  


b.

Using the ratchet buckle, tighten the 2 belts until there is no slack.

C368318C01
3.75,2.208 5.781,2.208 true 1.313,2.24 3.344,2.24 true 1.469,1.323 2.469,1.313 2.469,1.313 2.875,0.885 true 4.292,0.854 4.802,1.281 4.802,1.281 5.823,1.281 true 5.865,1.188 6.177,1.385 0.313,0.198 10 true *a 1.26,1.24 1.521,1.448 0.26,0.208 10 false *a 5.917,2.125 6.375,2.323 0.458,0.198 10 false SST 0.938,2.135 1.396,2.333 0.458,0.198 10 false SST
*a Ratchet Buckle - -



Hide 12372A 16.INSTALL ENGINE MOUNTING INSULATOR LH

a.

Install the engine mounting insulator LH to the automatic transaxle assembly with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 12360 17.INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

a.

Install the front engine mounting insulator assembly to the front engine mounting bracket with the bolt.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


Hide 18.REMOVE ENGINE SUPPORT BAR

a.

Remove the 2 bolts and SST (support bar) from the vehicle body.


b.

Remove the nut, stud bolt and SST (support bar) from the engine mounting bracket RH.


Hide 12362 20.INSTALL ENGINE MOUNTING INSULATOR RH

a.

Install the engine mounting insulator RH to the engine mounting bracket RH with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 36118A 21.INSTALL TRANSFER STIFFENER PLATE RH

a.
C296629C05
0.344,1.073 0.5,1.271 0.156,0.198 10 true A 0.49,0.656 0.646,0.854 0.156,0.198 10 true A 2.823,0.51 2.979,0.708 0.156,0.198 10 true B 3.01,1.26 3.167,1.458 0.156,0.198 10 true B

Temporarily install the transfer stiffener plate RH to the transfer case sub-assembly and rear engine mounting bracket with the 2 bolts (A) and 2 bolts (B).

HINT:
Bolt Length
·

Bolt (A): 35 mm (1.38 in.)

·

Bolt (B): 75 mm (2.95 in.)




b.

Tighten the 2 bolts (A).

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


c.

Tighten the 2 bolts (B) to install the transfer stiffener plate RH.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 23.REMOVE BELT

a.

Remove SST from the vehicle body.

C368333C02
1.448,2.677 3.094,2.677 true 4.021,2.646 5.74,2.646 true 5.865,2.563 6.323,2.76 0.458,0.198 10 false SST 1.146,2.594 1.604,2.792 0.458,0.198 10 false SST


b.

Connect the windshield washer jar assembly to the vehicle body with the bolt and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 32101A 24.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Remove any remaining adhesive from the 6 drive plate and torque converter assembly setting bolts.


b.
P000601C22
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 25.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the automatic transaxle case sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 26.REMOVE ENGINE SUPPORT BRIDGE

a.

Remove SST from the vehicle body.

NOTICE:

Prevent SST from contacting the vehicle body or windshield glass.



Hide 27.REMOVE ENGINE HANGER

a.

Remove the 2 bolts and No. 2 engine hanger from the cylinder head LH.


b.

Remove the bolt, SST (collar) and No. 1 engine hanger from engine hanger attachment.


c.

Remove the 2 bolts and SST (engine hanger attachment) from cylinder head RH.


Hide 33.INSTALL STEERING LINK ASSEMBLY

a.

Install the steering link assembly to the front frame assembly with the 2 bolts and 2 nuts.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

NOTICE:
·

Make sure to tighten the bolts starting from the steering link assembly pinion shaft side.

·

Keep the nut from rotating while turning the bolt because the nut has its own stopper.




Hide 34.INSTALL FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer bar with front stabilizer link assembly to the front frame assembly.


Hide 48824A 36.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Use the same procedure as for the LH side.


Hide 43420G 37.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side)

Hide 48069 39.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 40.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 45460 42.CONNECT TIE ROD ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 48810 46.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 47.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 37100 48.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17173 49.INSTALL EXHAUST MANIFOLD TO HEAD GASKET (for Bank 1)

Hide 17141 50.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 17410 51.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17584B 52.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

Hide 17403 53.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

Hide 54.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the cylinder head RH with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Engage the hose clamp and 3 wire harness clamps.


c.

Connect the air fuel ratio sensor (for Bank 1) connector.


Hide 47220D 55.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for LHD)

Hide 35104V 56.INSTALL BREATHER PLUG HOSE

a.

Engage the 3 hose clamps to install the breather plug hose.


Hide 82121 57.CONNECT ENGINE WIRE

a.
C368323C01
1.802,2.052 2.219,1.094 2.219,1.094 2.417,1.094 true 0.438,2.948 0.646,2.948 true 1.167,1.948 1.323,2.146 0.156,0.198 10 true A 1.854,0.833 2,1 0.146,0.167 10 true B 1.438,3.229 1.698,3.438 0.26,0.208 10 true *a 1,1.375 1.208,1.583 0.208,0.208 10 true *b 2.479,1 2.792,1.198 0.313,0.198 10 false *1 0.188,2.854 0.406,3.063 0.219,0.208 10 true *2
*a Transmission Wire Connector
*b Park/Neutral Position Switch Assembly Connector
*1 Engine Wire
*2 Earth Wire
V100135

Bolt
V100136

Nut


Engage the clamp to connect the engine wire.


b.

Connect the earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.

Connect the engine wire to the automatic transaxle case sub-assembly with the 2 bolts and nut.

Torque:
Bolt (A) : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Bolt (B) : 19.1 N*m (195 kgf*cm, 14 ft.*lbf)
Nut : 19.1 N*m (195 kgf*cm, 14 ft.*lbf)


d.

Connect the park/neutral position switch connector.


e.

Connect the connector of the transmission wire connector and rotate the lever to engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 17176 58.INSTALL AIR SURGE TANK TO INTAKE MANIFOLD GASKET

Hide 17190 59.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

Hide 25860 60.CONNECT PURGE VALVE (PURGE VSV)

Hide 22030 61.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 32943 63.CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE

Hide 32942 64.CONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 16570 65.INSTALL RADIATOR PIPE ASSEMBLY

a.

Install the radiator pipe assembly to the automatic transaxle assembly with the bolt.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 16267H 66.CONNECT NO. 3 WATER BY-PASS HOSE

Hide 16281K 67.CONNECT NO. 4 WATER BY-PASS HOSE

Hide 33820B 68.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 28100 69.INSTALL STARTER ASSEMBLY

Hide 55701J 70.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 71.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 72.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 73.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 79.INSPECT FOR EXHAUST GAS LEAK

Hide 53737B 80.INSTALL FRONT FENDER APRON SEAL LH

Hide 53736 81.INSTALL FRONT FENDER APRON SEAL RH

Hide 51442 85.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 86.INSTALL NO. 1 ENGINE UNDER COVER

Hide 88.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 90.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION