Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) U

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>SYSTEM DIAGRAM

·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 2 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 2 global CAN junction connector.

i.

Connection diagram

C424505C01
0.615,0.75 1.052,1.031 0.438,0.281 0.719,0.792 1.104,1.021 0.385,0.229 10 false H90 0.125,0.083 0.448,0.354 0.323,0.271 10 false *a
*a Front view of wire harness connector
(to No. 2 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 2 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H90-2 (CANH) BE Rack and pinion power steering gear assembly
(for Bus 4)
H90-12 (CANL) W
H90-3 (CANH) B Brake actuator assembly
(for Bus 4)
H90-13 (CANL) W
H90-5 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 4)
H90-15 (CANL) W
H90-6 (CANH) L 4WD ECU assembly
(for Bus 4)
H90-16 (CANL) W
H90-7 (CANH) V Steering sensor
(for Bus 4)
H90-17 (CANL) W
H90-8 (CANH) R Airbag sensor assembly
(for Bus 4)
H90-18 (CANL) W
H90-9 (CANH) P Tire pressure warning ECU and receiver
(for Bus 4)
H90-19 (CANL) W




NO. 3 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 3 global CAN junction connector.

i.

Connection diagram

C424505C02
0.615,0.75 1.052,1.031 0.438,0.281 0.719,0.792 1.104,1.021 0.385,0.229 10 false H91 0.083,0.073 0.448,0.344 0.365,0.271 10 false *a
*a Front view of wire harness connector
(to No. 3 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 3 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H91-2 (CANH) LG Central gateway ECU (network gateway ECU)
(for Bus 5)
H91-12 (CANL) W
H91-3 (CANH) G Certification ECU (smart key ECU assembly)
(for Bus 5)
H91-13 (CANL) W
H91-4 (CANH) SB Air conditioning amplifier assembly
(for Bus 5)
H91-14 (CANL) W
H91-5 (CANH) P Outer mirror control ECU assembly RH*
(for Bus 5)
H91-15 (CANL) W
H91-6 (CANH) B No. 4 global CAN junction connector
(for Bus 5)
H91-16 (CANL) W

*: w/ Seat Position Memory System





NO. 4 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 4 global CAN junction connector.

i.

Connection diagram

C424507C01
1.188,0.844 1.656,1.115 0.469,0.271 1.292,0.885 1.75,1.083 0.458,0.198 10 false H92 0.125,0.073 0.479,0.344 0.354,0.271 10 false *a
*a Front view of wire harness connector
(to No. 4 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 4 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H92-1 (CANH) BE Main body ECU (multiplex network body ECU)
(for Bus 5)
H92-7 (CANL) W
H92-2 (CANH) LG Meter mirror sub-assembly*1
(for Bus 5)
H92-8 (CANL) W
H92-3 (CANH) B No. 3 global CAN junction connector
(for Bus 5)
H92-9 (CANL) W
H92-4 (CANH) R No. 9 global CAN junction connector
(for Bus 5)
H92-10 (CANL) W
H92-5 (CANH) P Outer mirror control ECU assembly LH*2
(for Bus 5)
H92-11 (CANL) W

·

*1: w/ Headup Display System

·

*2: w/ Seat Position Memory System





NO. 5 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 5 global CAN junction connector.

i.

Connection diagram

C424507C02
1.188,0.844 1.656,1.115 0.469,0.271 1.292,0.885 1.75,1.083 0.458,0.198 10 false H93 0.125,0.073 0.479,0.344 0.354,0.271 10 false *a
*a Front view of wire harness connector
(to No. 5 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 5 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H93-1 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
H93-7 (CANL) W
H93-2 (CANH) R Millimeter wave radar sensor assembly*1
(for Bus 1)
H93-8 (CANL) W
H93-3 (CANH) L Forward recognition camera*1
(for Bus 1)
H93-9 (CANL) W
H93-4 (CANH) B No. 10 global CAN junction connector
(for Bus 1)
H93-10 (CANL) W
H93-5 (CANH) L Clearance warning ECU assembly
(for Bus 1)
H93-11 (CANL) W
H93-6 (CANH) GR Parking assist ECU*2
(for Bus 1)
H93-12 (CANL) W

·

*1: w/ Toyota Safety Sense

·

*2: w/ Panoramic View Monitor System





NO. 6 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 6 global CAN junction connector.

i.

Connection diagram

C424506C10
1.115,0.677 1.552,0.948 0.438,0.271 0.135,0.083 0.49,0.365 0.354,0.281 10 false *a 1.198,0.719 1.573,1.01 0.375,0.292 10 false H95
*a Front view of wire harness connector
(to No. 6 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 6 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H95-2 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 3)
H95-13 (CANL) W
H95-3 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 3)
H95-14 (CANL) W
H95-4 (CANH) B Radio and display receiver assembly
(for Bus 3)
H95-15 (CANL) W
H95-5 (CANH) R Telematics transceiver*
(for Bus 3)
H95-16 (CANL) W

*: w/ Telematics Transceiver





NO. 9 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 9 global CAN junction connector.

i.

Connection diagram

C424507C03
1.188,0.844 1.656,1.115 0.469,0.271 1.271,0.885 1.729,1.083 0.458,0.198 10 false M96 0.125,0.073 0.479,0.344 0.354,0.271 10 false *a
*a Front view of wire harness connector
(to No. 9 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 9 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M96-1 (CANH) LG Multiplex network door ECU
(for Bus 5)
M96-7 (CANL) W
M96-2 (CANH) G Position control ECU assembly LH*
(for Bus 5)
M96-8 (CANL) W
M96-3 (CANH) R No. 4 global CAN junction connector
(for Bus 5)
M96-9 (CANL) W
M96-4 (CANH) B Combination meter assembly
(for Bus 5)
M96-10 (CANL) W

*: w/ Seat Position Memory System





NO. 10 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 10 global CAN junction connector.

i.

Connection diagram

C424507C04
1.188,0.844 1.656,1.115 0.469,0.271 1.292,0.885 1.75,1.083 0.458,0.198 10 false M97 0.125,0.073 0.479,0.344 0.354,0.271 10 false *a
*a Front view of wire harness connector
(to No. 10 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 10 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M97-3 (CANH) V Blind spot monitor sensor LH
(for Bus 1)
M97-9 (CANL) W
M97-4 (CANH) B No. 1 CAN junction terminal
(for Bus 1)
M97-10 (CANL) W
M97-5 (CANH) R Rear television camera assembly*
(for Bus 1)
M97-11 (CANL) W
M97-6 (CANH) B No. 5 global CAN junction connector
(for Bus 1)
M97-12 (CANL) W

*: w/ Parking Assist Monitor System or Panoramic View Monitor System





NO. 11 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 11 global CAN junction connector.

i.

Connection diagram

C424506C02
1.115,0.677 1.552,0.948 0.438,0.271 0.135,0.083 0.49,0.365 0.354,0.281 10 false *a 1.198,0.719 1.573,1.01 0.375,0.292 10 false H97
*a Front view of wire harness connector
(to No. 11 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 11 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H97-9 (CANH) B ECM
(for Bus 2)
H97-20 (CANL) W
H97-11 (CANH) SB Central gateway ECU (network gateway ECU)
(for Bus 2)
H97-22 (CANL) W




NO. 1 CAN JUNCTION TERMINAL


a.

Check the No. 1 CAN junction terminal.

i.

Connection diagram

C285687C87
2.156,0.719 2.646,0.958 0.49,0.24 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 2.25,0.75 2.677,1.021 0.427,0.271 10 false M89
*a Front view of wire harness connector
(to No. 1 CAN Junction Terminal)
- -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.

Terminal No. (Symbol) Wiring Color Connected to
M89-3 (CANH) B No. 10 global CAN junction connector
(for Bus 1)
M89-2 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C428443C04
1.49,0.052 1.906,0.292 0.417,0.24 0.115,0.083 0.396,0.375 0.281,0.292 10 false *1 1.573,0.063 2.083,0.448 0.51,0.385 10 false H56
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H56-6 (CANH) - H56-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H56-6 (CANH) - H56-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H56-14 (CANL) - H56-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H56-6 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H56-14 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C424525C01
0.969,0.74 1.469,1.083 0.5,0.344 0.104,0.073 0.469,0.396 0.365,0.323 10 false *a 1.104,0.802 1.469,1.104 0.365,0.302 10 false H59
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H59 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C424526C01
0.917,0.76 1.417,1.052 0.5,0.292 0.135,0.104 0.521,0.333 0.385,0.229 10 false *a 1.042,0.792 1.427,1.052 0.385,0.26 10 false H59
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Diagnosis Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-14 (CA6H) - H59-5 (CA6L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
H59-14 (CA6H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-5 (CA6L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-14 (CA6H) - H59-1 (BATT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H59-5 (CA6L) - H59-1 (BATT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-23 (CA1H) - H59-8 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
H59-23 (CA1H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-8 (CA1L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-23 (CA1H) - H59-1 (BATT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H59-8 (CA1L) - H59-1 (BATT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-18 (CA4H) - H59-17 (CA4L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
H59-18 (CA4H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-17 (CA4L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-18 (CA4H) - H59-1 (BATT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H59-17 (CA4L) - H59-1 (BATT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-6 (CA3H) - H59-19 (CAYH) HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
H59-21 (CA3L) - H59-20 (CAYL) LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
H59-6 (CA3H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-21 (CA3L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-6 (CA3H) - H59-1 (BATT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H59-21 (CA3L) - H59-1 (BATT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-22 (CA2H) - H59-7 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
H59-22 (CA2H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-7 (CA2L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-22 (CA2H) - H59-1 (BATT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H59-7 (CA2L) - H59-1 (BATT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-15 (CA5H) - H59-16 (CA5L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
H59-15 (CA5H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-16 (CA5L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H59-15 (CA5H) - H59-1 (BATT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H59-16 (CA5L) - H59-1 (BATT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEERING SENSOR


C424527C01
2.333,1.385 2.698,1.656 0.365,0.271 4.771,1.167 5.177,1.448 0.406,0.281 0.104,0.094 0.427,0.333 0.323,0.24 10 false *a 2.448,1.427 2.74,1.677 0.292,0.25 10 false z5 4.844,1.208 5.198,1.469 0.354,0.26 10 false H57
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H57 steering sensor connector.


c.
C424528C01
1.49,0.156 1.948,0.479 0.458,0.323 0.125,0.094 0.458,0.385 0.333,0.292 10 false *a 1.583,0.229 1.917,0.521 0.333,0.292 10 false H57
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H57-3 (CANH) - H57-8 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H57-3 (CANH) - H57-6 (ESS) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H57-8 (CANL) - H57-6 (ESS) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H57-3 (CANH) - H57-4 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H57-8 (CANL) - H57-4 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A28 and C54 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

C424529C01
1.469,0.25 1.927,0.573 0.458,0.323 4.729,0.26 5.188,0.583 0.458,0.323 0.073,0.063 0.406,0.344 0.333,0.281 10 false *a 1.563,0.313 1.938,0.604 0.375,0.292 10 false A28 4.813,0.313 5.188,0.604 0.375,0.292 10 false C54
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A28-13 (CANH) - A28-26 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A28-13 (CANH) - C54-53 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A28-26 (CANL) - C54-53 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A28-13 (CANH) - A28-1 (BATT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A28-26 (CANL) - A28-1 (BATT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H21 combination meter assembly connector.


c.
C424531C01
1.51,0.188 1.99,0.5 0.479,0.313 0.094,0.094 0.448,0.417 0.354,0.323 10 false *a 1.604,0.219 1.958,0.542 0.354,0.323 10 false H21
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H21-32 (CANH) - H21-31 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
H21-32 (CANH) - H21-21 (ES) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H21-31 (CANL) - H21-21 (ES) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H21-32 (CANH) - H21-40 (B) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H21-31 (CANL) - H21-40 (B) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A39 brake actuator assembly connector.


c.
C427100C06
1.448,0.333 1.917,0.635 0.469,0.302 0.094,0.094 0.406,0.365 0.313,0.271 10 false *a 1.542,0.365 1.969,0.656 0.427,0.292 10 false A39
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A39-27 (CANH) - A39-43 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A39-27 (CANH) - A39-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A39-43 (CANL) - A39-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A39-27 (CANH) - A39-14 (+BS) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A39-43 (CANL) - A39-14 (+BS) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H43 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C424530C01
1.781,0.083 2.229,0.323 0.448,0.24 4.938,0.083 5.396,0.313 0.458,0.229 3.948,0.073 4.26,0.365 0.313,0.292 10 false *1 5.042,0.104 5.396,0.313 0.354,0.208 10 false H56 0.083,0.063 0.458,0.396 0.375,0.333 10 false *a 1.885,0.104 2.24,0.354 0.354,0.25 10 false H43
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H43-5 (CANH) - H43-4 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H43-5 (CANH) - H56-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H43-4 (CANL) - H56-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H43-5 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H43-4 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


c.
C424532C01
1.469,0.156 1.938,0.469 0.469,0.313 0.073,0.052 0.396,0.365 0.323,0.313 10 false *a 1.573,0.188 1.927,0.438 0.354,0.25 10 false H48
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H48-1 (CANH) - H48-2 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H48-1 (CANH) - H48-18 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H48-2 (CANL) - H48-18 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H48-1 (CANH) - H48-4 (+B) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H48-2 (CANL) - H48-4 (+B) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RACK AND PINION POWER STEERING GEAR ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the C67 rack and pinion power steering gear assembly connector.


c.
C424523C01
1.479,0.167 1.917,0.458 0.438,0.292 0.104,0.083 0.438,0.396 0.333,0.313 10 false *a 1.563,0.188 1.938,0.521 0.375,0.333 10 false C67
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
C67-10 (CANH) - C67-11 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C67-10 (CANH) - C67-7 (PGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C67-11 (CANL) - C67-7 (PGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C67-10 (CANH) - C67-8 (PIG) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C67-11 (CANL) - C67-8 (PIG) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H58 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C424558C01
1.802,0.188 2.167,0.448 0.365,0.26 5.094,0.292 5.458,0.552 0.365,0.26 0.135,0.063 0.448,0.26 0.313,0.198 10 false *a 3.708,0.094 4.021,0.292 0.313,0.198 10 false *1 1.865,0.229 2.281,0.563 0.417,0.333 10 false H58 5.167,0.333 5.479,0.531 0.313,0.198 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H58-26 (CANH) - H58-27 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
H58-26 (CANH) - H58-33 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H58-27 (CANL) - H58-33 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H58-26 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H58-27 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model with Automatic Air Conditioning System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H62 air conditioning amplifier assembly connector.


c.
C424522C01
1.531,0.146 1.99,0.448 0.458,0.302 0.115,0.125 0.458,0.385 0.344,0.26 10 false *a 1.615,0.188 1.958,0.448 0.344,0.26 10 false H62
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H62-2 (CANH) - H62-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H62-2 (CANH) - H62-17 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H62-1 (CANL) - H62-17 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H62-2 (CANH) - H62-5 (B) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H62-1 (CANL) - H62-5 (B) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C424535C03
1.76,0.135 2.115,0.375 0.354,0.24 4.969,0.063 5.385,0.313 0.417,0.25 3.76,0.083 4.073,0.313 0.313,0.229 10 false *1 1.854,0.167 2.208,0.406 0.354,0.24 10 false H2 0.073,0.063 0.417,0.344 0.344,0.281 10 false *a 5.042,0.094 5.385,0.396 0.344,0.302 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H2-13 (CANH) - H2-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H2-13 (CANH) - H56-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-14 (CANL) - H56-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-13 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H2-14 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M43 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C424536C01
0.333,0.792 0.76,1.104 0.427,0.313 4.875,0.135 5.292,0.417 0.417,0.281 3.594,0.094 3.896,0.344 0.302,0.25 10 false *1 0.417,0.844 0.792,1.156 0.375,0.313 10 false M43 0.063,0.052 0.375,0.344 0.313,0.292 10 false *a 4.958,0.167 5.323,0.406 0.365,0.24 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M43-2 (CA1P) - M43-7 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
M43-2 (CA1P) - M43-10 (BLGD) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M43-7 (CA1N) - M43-10 (BLGD) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M43-2 (CA1P) - H56-16 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M43-7 (CA1N) - H56-16 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

C424545C01
0.479,0.792 0.854,1.063 0.375,0.271 4.906,0.115 5.323,0.354 0.417,0.24 3.615,0.063 3.948,0.344 0.333,0.281 10 false *1 4.979,0.135 5.344,0.406 0.365,0.271 10 false H56 0.083,0.063 0.448,0.344 0.365,0.281 10 false *a 0.573,0.823 0.854,1.156 0.281,0.333 10 false R5
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
R5-5 (CA1P) - R5-11 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R5-5 (CA1P) - R5-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R5-11 (CA1N) - R5-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R5-5 (CA1P) - H56-16 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R5-11 (CA1N) - H56-16 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the B6 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C424543C01
0.438,0.792 0.792,1.073 0.354,0.281 4.917,0.094 5.313,0.354 0.396,0.26 3.594,0.073 3.958,0.313 0.365,0.24 10 false *1 4.99,0.125 5.313,0.427 0.323,0.302 10 false H56 0.083,0.073 0.469,0.385 0.385,0.313 10 false *a 0.51,0.823 1.115,1.24 0.604,0.417 10 false B6
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B6-3 (CA2H) - B6-2 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B6-3 (CA2H) - B6-1 (SGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B6-2 (CA2L) - B6-1 (SGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B6-3 (CA2H) - H56-16 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B6-2 (CA2L) - H56-16 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H10 telematics transceiver connector.


c.
C361493C75
1.469,0.167 1.979,0.469 0.51,0.302 1.604,0.24 2.063,0.438 0.458,0.198 10 false H10 0.125,0.063 0.583,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H10-15 (CANP) - H10-16 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H10-15 (CANP) - H10-4 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H10-16 (CANN) - H10-4 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H10-15 (CANP) - H10-1 (+B) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H10-16 (CANN) - H10-1 (+B) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System or Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the W15 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C424544C01
0.385,0.719 0.854,1.031 0.469,0.313 4.781,0.083 5.208,0.333 0.427,0.25 3.5,0.073 3.844,0.365 0.344,0.292 10 false *1 4.865,0.104 5.271,0.448 0.406,0.344 10 false H56 0.104,0.073 0.5,0.417 0.396,0.344 10 false *a 0.458,0.76 0.948,1.135 0.49,0.375 10 false W15
*1 DLC3 - -
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
W15-4 (CANH) - W15-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
W15-4 (CANH) - H56-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
W15-1 (CANL) - H56-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
W15-4 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
W15-1 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TIRE PRESSURE WARNING ECU AND RECEIVER


Refer to Terminals of ECU.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M51 tire pressure warning ECU and receiver connector.


c.
C424509C04
0.323,0.938 0.771,1.219 0.448,0.281 0.094,0.083 0.458,0.344 0.365,0.26 10 false *a 0.417,0.969 0.781,1.229 0.365,0.26 10 false M51
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M51-9 (CANH) - M51-10 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
M51-9 (CANH) - M51-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M51-10 (CANL) - M51-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M51-9 (CANH) - M51-7 (+B) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M51-10 (CANL) - M51-7 (+B) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H31 meter mirror sub-assembly connector.


c.
C424542C01
1.521,0.156 1.969,0.469 0.448,0.313 0.094,0.073 0.406,0.365 0.313,0.292 10 false *a 1.604,0.188 1.979,0.521 0.375,0.333 10 false H31
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H31-12 (MPX1) - H31-13 (MPX2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H31-12 (MPX1) - H31-4 (ES) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H31-13 (MPX2) - H31-4 (ES) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H31-12 (MPX1) - H31-2 (B) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H31-13 (MPX2) - H31-2 (B) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H46 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C424546C01
1.708,0.094 2.146,0.385 0.438,0.292 5.167,0.063 5.583,0.323 0.417,0.26 3.906,0.063 4.24,0.354 0.333,0.292 10 false *1 5.24,0.104 5.646,0.375 0.406,0.271 10 false H56 0.083,0.063 0.427,0.375 0.344,0.313 10 false *a 1.771,0.146 2.219,0.469 0.448,0.323 10 false H46
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H46-17 (R1) - H46-18 (R2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H46-17 (R1) - H46-28 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H46-18 (R2) - H46-28 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H46-17 (R1) - H56-16 (BAT) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H46-18 (R2) - H56-16 (BAT) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H20 parking assist ECU connector.


c.
C424537C01
1.51,0.125 1.948,0.427 0.438,0.302 0.063,0.094 0.427,0.375 0.365,0.281 10 false *a 1.594,0.167 1.958,0.448 0.365,0.281 10 false H20
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H20-11 (CANH) - H20-12 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H20-11 (CANH) - H20-4 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H20-12 (CANL) - H20-4 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H20-11 (CANH) - H20-1 (+B) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H20-12 (CANL) - H20-1 (+B) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POSITION CONTROL ECU ASSEMBLY LH (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the e23 and e25 position control ECU assembly LH connectors.


c.

Measure the resistance according to the value(s) in the table below.

C424540C01
1.583,0.052 2.031,0.323 0.448,0.271 5,0.25 5.448,0.521 0.448,0.271 0.073,0.052 0.458,0.354 0.385,0.302 10 false *a 1.667,0.083 2.073,0.375 0.406,0.292 10 false e25 5.104,0.271 5.51,0.563 0.406,0.292 10 false e23
*a Front view of wire harness connector
(to Position Control ECU Assembly LH)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
e25-13 (CANP) - e25-14 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
e25-13 (CANP) - e23-2 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
e25-14 (CANN) - e23-2 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
e25-13 (CANP) - e23-3 (+B) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
e25-14 (CANN) - e23-3 (+B) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the J23 outer mirror control ECU assembly LH connector.


c.
C424541C01
0.229,1.042 0.646,1.354 0.417,0.313 0.104,0.083 0.521,0.417 0.417,0.333 10 false *a 0.302,1.094 0.719,1.427 0.417,0.333 10 false J23
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J23-9 (CANP) - J23-8 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
J23-9 (CANP) - J23-7 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J23-8 (CANN) - J23-7 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J23-9 (CANP) - J23-6 (CPUB) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J23-8 (CANN) - J23-6 (CPUB) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the J7 outer mirror control ECU assembly RH connector.


c.
C424541C02
0.229,1.042 0.615,1.344 0.385,0.302 0.104,0.083 0.521,0.417 0.417,0.333 10 false *a 0.323,1.094 0.74,1.427 0.417,0.333 10 false J7
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J7-9 (CANP) - J7-8 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
J7-9 (CANP) - J7-7 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J7-8 (CANN) - J7-7 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J7-9 (CANP) - J7-6 (CPUB) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J7-8 (CANN) - J7-6 (CPUB) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MULTIPLEX NETWORK DOOR ECU


Refer to Terminals of ECU.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the W18 and W19 multiplex network door ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

C424539C01
1.604,0.083 2.042,0.365 0.438,0.281 5.104,0.125 5.542,0.406 0.438,0.281 0.156,0.073 0.521,0.354 0.365,0.281 10 false *a 1.677,0.135 2.083,0.406 0.406,0.271 10 false W18 5.188,0.167 5.594,0.438 0.406,0.271 10 false W19
*a Front view of wire harness connector
(to Multiplex Network Door ECU)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
W18-39 (CANP) - W18-40 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
W18-39 (CANP) - W19-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
W18-40 (CANN) - W19-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
W18-39 (CANP) - W19-1 (B) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
W18-40 (CANN) - W19-1 (B) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




4WD ECU ASSEMBLY


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M41 and M42 4WD ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C424548C01
0.604,0.771 1.042,1.063 0.438,0.292 4.156,0.813 4.594,1.104 0.438,0.292 0.708,0.813 1.583,1.385 0.875,0.573 10 false M41 0.094,0.073 0.49,0.365 0.396,0.292 10 false *a 4.24,0.854 4.719,1.167 0.479,0.313 10 false M42
*a Front view of wire harness connector
(to 4WD ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M42-17 (CANH) - M42-26 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
M42-17 (CANH) - M41-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M42-26 (CANL) - M41-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M42-17 (CANH) - M41-2 (BSLC) HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M42-26 (CANL) - M41-2 (BSLC) LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher