After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>SYSTEM DIAGRAM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 2 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 2 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 2 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 2 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H90-2 (CANH) | BE | Rack and pinion power steering gear assembly
(for Bus 4) |
| H90-12 (CANL) | W | |
| H90-3 (CANH) | B*1
GR*2 |
Brake actuator assembly
(for Bus 4) |
| H90-13 (CANL) | W | |
| H90-5 (CANH) | G | Central gateway ECU (network gateway ECU)
(for Bus 4) |
| H90-15 (CANL) | W | |
| H90-6 (CANH) | L | 4WD ECU assembly
(for Bus 4) |
| H90-16 (CANL) | W | |
| H90-7 (CANH) | V | Steering sensor
(for Bus 4) |
| H90-17 (CANL) | W | |
| H90-8 (CANH) | R | Airbag sensor assembly
(for Bus 4) |
| H90-18 (CANL) | W | |
| H90-9 (CANH) | P | Tire pressure warning ECU and receiver*3
(for Bus 4) |
| H90-19 (CANL) | W |
*1: for LHD
*2: for RHD
*3: w/ Tire Pressure Warning System
NO. 3 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 3 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 3 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H91-2 (CANH) | LG | Central gateway ECU (network gateway ECU)
(for Bus 5) |
| H91-12 (CANL) | W | |
| H91-3 (CANH) | G | Certification ECU (smart key ECU assembly)
(for Bus 5) |
| H91-13 (CANL) | W | |
| H91-4 (CANH) | SB | Air conditioning amplifier assembly
(for Bus 5) |
| H91-14 (CANL) | W | |
| H91-5 (CANH) | P | Outer mirror control ECU assembly RH*
(for Bus 5) |
| H91-15 (CANL) | W | |
| H91-6 (CANH) | B | No. 4 global CAN junction connector
(for Bus 5) |
| H91-16 (CANL) | W |
*: w/ Seat Position Memory System
NO. 4 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 4 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 4 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H92-1 (CANH) | BE | Main body ECU (multiplex network body ECU)
(for Bus 5) |
| H92-7 (CANL) | W | |
| H92-2 (CANH) | LG | Meter mirror sub-assembly*1
(for Bus 5) |
| H92-8 (CANL) | W | |
| H92-3 (CANH) | B | No. 3 global CAN junction connector
(for Bus 5) |
| H92-9 (CANL) | W | |
| H92-4 (CANH) | R | No. 9 global CAN junction connector
(for Bus 5) |
| H92-10 (CANL) | W | |
| H92-5 (CANH) | P | Outer mirror control ECU assembly LH*2
(for Bus 5) |
| H92-11 (CANL) | W |
*1: w/ Headup Display System
*2: w/ Seat Position Memory System
NO. 5 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 5 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 5 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 5 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H93-1 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| H93-7 (CANL) | W | |
| H93-2 (CANH) | R | Millimeter wave radar sensor assembly*1
(for Bus 1) |
| H93-8 (CANL) | W | |
| H93-3 (CANH) | L | Forward recognition camera*1
(for Bus 1) |
| H93-9 (CANL) | W | |
| H93-4 (CANH) | B | No. 10 global CAN junction connector
(for Bus 1) |
| H93-10 (CANL) | W | |
| H93-5 (CANH) | L | Clearance warning ECU assembly
(for Bus 1) |
| H93-11 (CANL) | W | |
| H93-6 (CANH) | GR | Parking assist ECU*2
(for Bus 1) |
| H93-12 (CANL) | W |
*1: w/ Toyota Safety Sense
*2: w/ Panoramic View Monitor System
NO. 6 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 6 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 6 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 6 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H95-2 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 3) |
| H95-13 (CANL) | W | |
| H95-3 (CANH) | G | Central gateway ECU (network gateway ECU)
(for Bus 3) |
| H95-14 (CANL) | W | |
| H95-4 (CANH) | B | Radio and display receiver assembly
(for Bus 3) |
| H95-15 (CANL) | W | |
| H95-5 (CANH) | R | Telematics transceiver*
(for Bus 3) |
| H95-16 (CANL) | W |
*: w/ Telematics Transceiver
NO. 9 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 9 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 9 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M96-1 (CANH) | LG | Multiplex network door ECU*1
(for Bus 5) |
| M96-7 (CANL) | W | |
| M96-2 (CANH) | G | ·
Position control ECU assembly LH*2 ·
Position control ECU assembly RH*3 (for Bus 5) |
| M96-8 (CANL) | W | |
| M96-3 (CANH) | R | No. 4 global CAN junction connector
(for Bus 5) |
| M96-9 (CANL) | W | |
| M96-4 (CANH) | B | Combination meter assembly
(for Bus 5) |
| M96-10 (CANL) | W |
*1: w/ Power Back Door System
*2: for LHD with Seat Position Memory System
*3: for RHD with Seat Position Memory System
NO. 10 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 10 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 10 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 10 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M97-3 (CANH) | V | Blind spot monitor sensor LH
(for Bus 1) |
| M97-9 (CANL) | W | |
| M97-4 (CANH) | B | No. 1 CAN junction terminal
(for Bus 1) |
| M97-10 (CANL) | W | |
| M97-5 (CANH) | R | Rear television camera assembly*
(for Bus 1) |
| M97-11 (CANL) | W | |
| M97-6 (CANH) | B | No. 5 global CAN junction connector
(for Bus 1) |
| M97-12 (CANL) | W |
*: w/ Parking Assist Monitor System or Panoramic View Monitor System
NO. 11 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 11 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 11 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 11 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H97-9 (CANH) | B | ECM
(for Bus 2) |
| H97-20 (CANL) | W | |
| H97-10 (CANH) | R | Engine stop and start ECU*
(for Bus 2) |
| H97-21 (CANL) | W | |
| H97-11 (CANH) | SB | Central gateway ECU (network gateway ECU)
(for Bus 2) |
| H97-22 (CANL) | W |
*: w/ Stop and Start System
NO. 1 CAN JUNCTION TERMINAL
Check the No. 1 CAN junction terminal.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Terminal) |
- | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M89-3 (CANH) | B | No. 10 global CAN junction connector
(for Bus 1) |
| M89-2 (CANL) | W |
DLC3
Disconnect the cable from the negative (-) battery terminal.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H56-6 (CANH) - H56-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H56-6 (CANH) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H56-14 (CANL) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H56-6 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H56-14 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
| *a | Component without harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H59 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-14 (CA6H) - H59-5 (CA6L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| H59-14 (CA6H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-5 (CA6L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-14 (CA6H) - H59-1 (BATT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H59-5 (CA6L) - H59-1 (BATT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-23 (CA1H) - H59-8 (CA1L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| H59-23 (CA1H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-8 (CA1L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-23 (CA1H) - H59-1 (BATT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H59-8 (CA1L) - H59-1 (BATT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-18 (CA4H) - H59-17 (CA4L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| H59-18 (CA4H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-17 (CA4L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-18 (CA4H) - H59-1 (BATT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H59-17 (CA4L) - H59-1 (BATT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-6 (CA3H) - H59-19 (CAYH) | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| H59-21 (CA3L) - H59-20 (CAYL) | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| H59-6 (CA3H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-21 (CA3L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-6 (CA3H) - H59-1 (BATT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H59-21 (CA3L) - H59-1 (BATT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-22 (CA2H) - H59-7 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| H59-22 (CA2H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-7 (CA2L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-22 (CA2H) - H59-1 (BATT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H59-7 (CA2L) - H59-1 (BATT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-15 (CA5H) - H59-16 (CA5L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| H59-15 (CA5H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-16 (CA5L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-15 (CA5H) - H59-1 (BATT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H59-16 (CA5L) - H59-1 (BATT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STEERING SENSOR
| *a | Component without harness connected
(Steering Sensor) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H57 steering sensor connector.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H57-3 (CANH) - H57-8 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H57-3 (CANH) - H57-6 (ESS) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H57-8 (CANL) - H57-6 (ESS) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H57-3 (CANH) - H57-4 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H57-8 (CANL) - H57-4 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) battery terminal.
Disconnect the A28 and C54 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A28-13 (CANH) - A28-26 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A28-13 (CANH) - C54-53 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A28-26 (CANL) - C54-53 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A28-13 (CANH) - A28-1 (BATT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A28-26 (CANL) - A28-1 (BATT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H21 combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H21-32 (CANH) - H21-31 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| H21-32 (CANH) - H21-21 (ES) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H21-31 (CANL) - H21-21 (ES) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H21-32 (CANH) - H21-40 (B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H21-31 (CANL) - H21-40 (B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the A39 brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A39-27 (CANH) - A39-43 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A39-27 (CANH) - A39-1 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A39-43 (CANL) - A39-1 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A39-27 (CANH) - A39-14 (+BS) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A39-43 (CANL) - A39-14 (+BS) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H43-5 (CANH) - H43-4 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H43-5 (CANH) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H43-4 (CANL) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H43-5 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H43-4 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H48 certification ECU (smart key ECU assembly) connector.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H48-1 (CANH) - H48-2 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H48-1 (CANH) - H48-18 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H48-2 (CANL) - H48-18 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H48-1 (CANH) - H48-4 (+B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H48-2 (CANL) - H48-4 (+B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
RACK AND PINION POWER STEERING GEAR ASSEMBLY
Refer to Terminals of ECU.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the C67 rack and pinion power steering gear assembly connector.
| *a | Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| C67-10 (CANH) - C67-11 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| C67-10 (CANH) - C67-7 (PGND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C67-11 (CANL) - C67-7 (PGND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C67-10 (CANH) - C67-8 (PIG) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| C67-11 (CANL) - C67-8 (PIG) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H58 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H58-26 (CANH) - H58-27 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| H58-26 (CANH) - H58-33 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H58-27 (CANL) - H58-33 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H58-26 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H58-27 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
Refer to Terminals of ECU.
for Automatic Air Conditioning System:
for Manual Air Conditioning System:
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H62 air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H62-2 (CANH) - H62-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H62-2 (CANH) - H62-17 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H62-1 (CANL) - H62-17 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H62-2 (CANH) - H62-5 (B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H62-1 (CANL) - H62-5 (B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER ASSEMBLY
Refer to Terminals of ECU.
for Audio and Visual System:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>TERMINALS OF ECU
for Navigation System:
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H2 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H2-13 (CANH) - H2-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H2-13 (CANH) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H2-14 (CANL) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H2-13 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H2-14 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR LH
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the M43 blind spot monitor sensor LH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| M43-2 (CA1P) - M43-7 (CA1N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| M43-2 (CA1P) - M43-10 (BLGD) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M43-7 (CA1N) - M43-10 (BLGD) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M43-2 (CA1P) - H56-16 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M43-7 (CA1N) - H56-16 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the R5 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| R5-5 (CA1P) - R5-11 (CA1N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| R5-5 (CA1P) - R5-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R5-11 (CA1N) - R5-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R5-5 (CA1P) - H56-16 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| R5-11 (CA1N) - H56-16 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the B6 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B6-3 (CA2H) - B6-2 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B6-3 (CA2H) - B6-1 (SGND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B6-2 (CA2L) - B6-1 (SGND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B6-3 (CA2H) - H56-16 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B6-2 (CA2L) - H56-16 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H10 telematics transceiver connector.
| *a | Front view of wire harness connector
(to Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H10-15 (CANP) - H10-16 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H10-15 (CANP) - H10-4 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H10-16 (CANN) - H10-4 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H10-15 (CANP) - H10-1 (+B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H10-16 (CANN) - H10-1 (+B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System or Panoramic View Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the W15 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| W15-4 (CANH) - W15-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| W15-4 (CANH) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| W15-1 (CANL) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| W15-4 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| W15-1 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)
Refer to Terminals of ECU.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the M51 tire pressure warning ECU and receiver connector.
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| M51-9 (CANH) - M51-10 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| M51-9 (CANH) - M51-12 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M51-10 (CANL) - M51-12 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M51-9 (CANH) - M51-7 (+B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M51-10 (CANL) - M51-7 (+B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H31 meter mirror sub-assembly connector.
| *a | Front view of wire harness connector
(to Meter Mirror Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H31-12 (MPX1) - H31-13 (MPX2) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H31-12 (MPX1) - H31-4 (ES) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H31-13 (MPX2) - H31-4 (ES) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H31-12 (MPX1) - H31-2 (B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H31-13 (MPX2) - H31-2 (B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY
Refer to Terminals of ECU.
Toyota Parking Assist-sensor System (w/o Parking Support Brake System)
Toyota Parking Assist-sensor System (w/ Parking Support Brake System (Forward/reverse Type))
Toyota Parking Assist-sensor System (w/ Parking Support Brake System (Reverse Only Type))
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H46 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H46-17 (R1) - H46-18 (R2) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H46-17 (R1) - H46-28 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H46-18 (R2) - H46-28 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H46-17 (R1) - H56-16 (BAT) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H46-18 (R2) - H56-16 (BAT) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
PARKING ASSIST ECU (w/ Panoramic View Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H20 parking assist ECU connector.
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H20-11 (CANH) - H20-12 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H20-11 (CANH) - H20-4 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H20-12 (CANL) - H20-4 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H20-11 (CANH) - H20-1 (+B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H20-12 (CANL) - H20-1 (+B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POSITION CONTROL ECU ASSEMBLY LH (for LHD with Seat Position Memory System)
Refer to Terminals of ECU.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the e23 and e25 position control ECU assembly LH connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Position Control ECU Assembly LH) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| e25-13 (CANP) - e25-14 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| e25-13 (CANP) - e23-2 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| e25-14 (CANN) - e23-2 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| e25-13 (CANP) - e23-3 (+B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| e25-14 (CANN) - e23-3 (+B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POSITION CONTROL ECU ASSEMBLY RH (for RHD with Seat Position Memory System)
Refer to Terminals of ECU.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the e23 and e25 position control ECU assembly RH connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Position Control ECU Assembly RH) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| e25-13 (CANP) - e25-14 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| e25-13 (CANP) - e23-2 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| e25-14 (CANN) - e23-2 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| e25-13 (CANP) - e23-3 (+B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| e25-14 (CANN) - e23-3 (+B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Seat Position Memory System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the J23 outer mirror control ECU assembly LH connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| J23-9 (CANP) - J23-8 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| J23-9 (CANP) - J23-7 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| J23-8 (CANN) - J23-7 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| J23-9 (CANP) - J23-6 (CPUB) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| J23-8 (CANN) - J23-6 (CPUB) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Seat Position Memory System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the J7 outer mirror control ECU assembly RH connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| J7-9 (CANP) - J7-8 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| J7-9 (CANP) - J7-7 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| J7-8 (CANN) - J7-7 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| J7-9 (CANP) - J7-6 (CPUB) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| J7-8 (CANN) - J7-6 (CPUB) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the W18 and W19 multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Multiplex Network Door ECU) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| W18-39 (CANP) - W18-40 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| W18-39 (CANP) - W19-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| W18-40 (CANN) - W19-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| W18-39 (CANP) - W19-1 (B) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| W18-40 (CANN) - W19-1 (B) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
4WD ECU ASSEMBLY
Refer to Terminals of ECU.
for Dynamic Torque Control AWD System
Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>TERMINALS OF ECU
for Dynamic Torque Vectoring AWD System
Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE VECTORING AWD SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the M41 and M42 4WD ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to 4WD ECU Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| M42-17 (CANH) - M42-26 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| M42-17 (CANH) - M41-1 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M42-26 (CANL) - M41-1 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M42-17 (CANH) - M41-2 (BSLC) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M42-26 (CANL) - M41-2 (BSLC) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ENGINE STOP AND START ECU (w/ Stop and Start System)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the H66 and A33 engine stop and start ECU connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Engine Stop and Start ECU) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H66-13 (CANH) - H66-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H66-13 (CANH) - A33-8 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H66-14 (CANL) - A33-8 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H66-13 (CANH) - A33-3 (BIN1) | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H66-14 (CANL) - A33-3 (BIN1) | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |